| Age | Commit message (Collapse) | Author |
|---|
|
Use the per port counter attached to all QPs created on that port to
implement port level packets/bytes performance counters a la IB.
Derived from a patch by Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Allocate flow counter per Ethernet/IBoE port, and attach this counter
to all the QPs created on that port. Based on patch by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
IBoE doesn't use LIDs. Use the GID change event to update the IB core
cache for addition/deletion of GIDs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW revision is derived from device ID and rev id.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The newest device firmware stores IB vs. Ethernet protocol in two bits
in members_count field of multicast group table (0: Infiniband, 1:
Ethernet). When changing the QP members count for a multicast group,
it important not to reset this information. When calling multicast
attach first time, the protocol type should be specified. In this
patch we always set it IB, but in the future we will handle Ethernet
too. When looking for a QP, the protocol type shoud be checked too.
Signed-off-by: Aleksey Senin <alekseys@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Some systems have PCI addresses that don't fit in unsigned long (eg some
32-bit PowerPC 440 systems have 36-bit bus addresses). Fix up mlx4 drivers
by using phys_addr_t where appropriate, so we don't truncate any PCI
resource addresses before ioremapping them.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (42 commits)
IB/qib: Fix refcount leak in lkey/rkey validation
IB/qib: Improve SERDES tunning on QMH boards
IB/qib: Unnecessary delayed completions on RC connection
IB/qib: Issue pre-emptive NAKs on eager buffer overflow
IB/qib: RDMA lkey/rkey validation is inefficient for large MRs
IB/qib: Change QPN increment
IB/qib: Add fix missing from earlier patch
IB/qib: Change receive queue/QPN selection
IB/qib: Fix interrupt mitigation
IB/qib: Avoid duplicate writes to the rcv head register
IB/qib: Add a few new SERDES tunings
IB/qib: Reset packet list after freeing
IB/qib: New SERDES init routine and improvements to SI quality
IB/qib: Clear WAIT_SEND flags when setting QP to error state
IB/qib: Fix context allocation with multiple HCAs
IB/qib: Fix multi-Florida HCA host panic on reboot
IB/qib: Handle transitions from ACTIVE_DEFERRED to ACTIVE better
IB/qib: UD send with immediate receive completion has wrong size
IB/qib: Set port physical state even if other fields are invalid
IB/qib: Generate completion callback on errors
...
|
|
ib_create_send_mad() can return ERR_PTR(-ENOMEM) here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
mlx4_ib_free_cq_buf() should not be called under spin_lock_irq() since
it calls dma_free_coherent(), which needs irqs enabled. Fix this by
deferring the free to outside the locked region.
This was found due to the
WARN_ON(irqs_disabled());
in swiotlb_free_coherent().
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
net/ipv4/fib_frontend.c
|
|
Use netif_running() and netif_carrier_ok() to report link state,
exactly as is done to report Ethernet link state in sysfs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The link rate is the product of the link speed in the link width. For
Etherent ports the rate is 10G, so we use 1 for the width and 4 for
speed to get the correct rate.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
We must fully update the control segment before marking it as valid,
so that hardware doesn't start executing it before we're ready.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Move VLAN control bit setting to before wmb(). - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
dev_base_lock is the legacy way to lock the device list, and is planned
to disappear. (writers hold RTNL, readers hold RCU lock)
Convert rdma_translate_ip() and update_ipv6_gids() to RCU locking.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (63 commits)
IB/qib: clean up properly if pci_set_consistent_dma_mask() fails
IB/qib: Allow driver to load if PCIe AER fails
IB/qib: Fix uninitialized pointer if CONFIG_PCI_MSI not set
IB/qib: Fix extra log level in qib_early_err()
RDMA/cxgb4: Remove unnecessary KERN_<level> use
RDMA/cxgb3: Remove unnecessary KERN_<level> use
IB/core: Add link layer type information to sysfs
IB/mlx4: Add VLAN support for IBoE
IB/core: Add VLAN support for IBoE
IB/mlx4: Add support for IBoE
mlx4_en: Change multicast promiscuous mode to support IBoE
mlx4_core: Update data structures and constants for IBoE
mlx4_core: Allow protocol drivers to find corresponding interfaces
IB/uverbs: Return link layer type to userspace for query port operation
IB/srp: Sync buffer before posting send
IB/srp: Use list_first_entry()
IB/srp: Reduce number of BUSY conditions
IB/srp: Eliminate two forward declarations
IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
IB: Replace EXTRA_CFLAGS with ccflags-y
...
|
|
'misc', 'mlx4', 'nes', 'qib' and 'srp' into for-next
|
|
This patch allows IBoE traffic to be encapsulated in 802.1Q tagged
VLAN frames. The VLAN tag is encoded in the GID and derived from it
by a simple computation.
The netdev notifier callback is modified to catch VLAN device
addition/removal and the port's GID table is updated to reflect the
change, so that for each netdevice there is an entry in the GID table.
When the port's GID table is exhausted, GID entries will not be added.
Only children of the main interfaces can add to the GID table; if a
VLAN interface is added on another VLAN interface (e.g. "vconfig add
eth2.6 8"), then that interfaces will not add an entry to the GID
table.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add 802.1q VLAN support to IBoE. The VLAN tag is encoded within the
GID derived from a link local address in the following way:
GID[11] GID[12] contain the VLAN ID when the GID contains a VLAN.
The 3 bits user priority field of the packets are identical to the 3
bits of the SL.
In case of rdma_cm apps, the TOS field is used to generate the SL
field by doing a shift right of 5 bits effectively taking to 3 MS bits
of the TOS field.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add support for IBoE to mlx4_ib. The bulk of the code is handling the
new address vector fields; mlx4 needs the MAC address of a remote node
to include it in a WQE (for datagrams) or in the QP context (for
connected QPs). Address resolution is done by assuming all unicast
GIDs are either link-local IPv6 addresses.
Multicast group attach/detach needs to update the NIC's multicast
filters; but since attaching a QP to a multicast group can be done
before the QP is bound to a port, for IBoE we need to keep track of
all multicast groups that a QP is attached too before it transitions
from INIT to RTR (since it does not have a port in the INIT state).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Many things cleaned up and otherwise monkeyed with; hope I didn't
introduce too many bugs. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The Node Description cannot be changed via MADs (it is read-only).
Until now, it was changed in the driver via sysfs, and the new Node
Description was simply inserted by the driver into MAD responses
(replacing the description returned by FW).
System startup scripts use the sysfs interface to change the node
description at driver startup to show the hostname, etc. However, this
has a race condition: the SM could discover the original FW node
description rather than the system-specific description if it queried the
port before the startup scripts finish running.
For mlx4, we fix this with a new FW command (SET_NODE) that allows
passing the new node description to FW. When this command is invoked,
FW sends a trap 144 to the SM. When it gets this trap, the SM can
query the node to obtain the new node description -- thus eliminating
the effects of the race.
This patch simply calls SET_NODE command when a new node description
is entered via sysfs (thus causing trap 144 to be issued by the FW).
We ignore all failures of the SET_NODE command (including those caused
by using a device FW that predates the SET_NODE command), since in
that case things work just as before.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fix kconfig dependency warning to satisfy dependencies:
warning: (MLX4_EN && NETDEVICES && NETDEV_10000 && PCI && INET || MLX4_INFINIBAND && INFINIBAND) selects MLX4_CORE which has unmet direct dependencies (NETDEVICES && NETDEV_10000 && PCI)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for packing IBoE packet headers.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Clean up and fix ib_ud_header_init() a bit. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fix the limit on the size of max fast registration WRs that can be
posted to match hardware capabilities.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add a new parameter to ib_register_device() so that low-level device
drivers can pass in a pointer to a callback function that will be
called for each port that is registered in sysfs. This allows
low-level device drivers to create files in
/sys/class/infiniband/<hca>/ports/<N>/
without having to poke through the internals of the RDMA sysfs handling.
There is no need for an unregister function since the kobject
reference will go to zero when ib_unregister_device() is called.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add support for masked atomic operations (masked compare and swap,
masked fetch and add).
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Check correct variable for allocation failure
RDMA/nes: Correct cap.max_inline_data assignment in nes_query_qp()
RDMA/cm: Set num_paths when manually assigning path records
IB/cm: Fix device_create() return value check
|
|
The intent here is to check the "mfrpl->mapped_page_list" allocation.
We checked "mfrpl->ibfrpl.page_list" earlier.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
Conflicts:
drivers/infiniband/core/uverbs_main.c
|
|
ib_ud_header_init() first clears header and then fills up the various
fields. Later on, it tests header->immediate_present, which it has
already cleared, so the condition is always false. Fix this by adding
an immediate_present parameter and setting header->immediate_present
as is done with grh_present. Also remove unused calculation of
header_len.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
struct ib_qp already holds a pointer to the ib device. No need to dive to the
hw device object to retrieve it.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
In mlx4_ib_post_recv(), we should check the queue for overflow using
recv_cq instead of send_cq (current code looks like a copy-and-paste
mistake).
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
As for memfree mthca hardware, ConnectX also requires SRQ WQE scatter
entries to be initialized with the invalid L_Key at SRQ creation time.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (45 commits)
RDMA/cxgb3: Fix error paths in post_send and post_recv
RDMA/nes: Fix stale ARP issue
RDMA/nes: FIN during MPA startup causes timeout
RDMA/nes: Free kmap() resources
RDMA/nes: Check for zero STag
RDMA/nes: Fix Xansation test crash on cm_node ref_count
RDMA/nes: Abnormal listener exit causes loopback node crash
RDMA/nes: Fix crash in nes_accept()
RDMA/nes: Resource not freed for REJECTed connections
RDMA/nes: MPA request/response error checking
RDMA/nes: Fix query of ORD values
RDMA/nes: Fix MAX_CM_BUFFER define
RDMA/nes: Pass correct size to ioremap_nocache()
RDMA/nes: Update copyright and branding string
RDMA/nes: Add max_cqe check to nes_create_cq()
RDMA/nes: Clean up struct nes_qp
RDMA/nes: Implement IB_SIGNAL_ALL_WR as an iWARP extension
RDMA/nes: Add additional SFP+ PHY uC status check and PHY reset
RDMA/nes: Correct fast memory registration implementation
IB/ehca: Fix error paths in post_send and post_recv
...
|
|
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Current code has a limitation: an LSO header is not allowed to cross a
64 byte boundary. This patch removes this limitation by setting the
WQE RR for large headers thus allowing LSO headers of any size. The
extra buffer reserved for MLX4_IB_QP_LSO QPs has been doubled, from 64
to 128 bytes, assuming this is reasonable upper limit for header
length. Also, this patch will cause IB_DEVICE_UD_TSO to be set only
for HCA FW versions that set MLX4_DEV_CAP_FLAG_BLH; e.g. FW version
2.6.000 and higher.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
There is no such flag DE - the field is reserved and should be zero.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
and 'nes' into for-linus
|
|
Userspace apps are supposed to release all ib device resources if they
receive a fatal async event (IBV_EVENT_DEVICE_FATAL). However, the
app has no way of knowing when the device has come back up, except to
repeatedly attempt ibv_open_device() until it succeeds.
However, currently there is no protection against the open succeeding
while the device is in being removed following the fatal event. In
this case, the open will succeed, but as a result the device waits in
the middle of its removal until the new app releases its resources --
and the new app will not do so, since the open succeeded at a point
following the fatal event generation.
This patch adds an "active" flag to the device. The active flag is set
to false (in the fatal event flow) before the "fatal" event is
generated, so any subsequent ibv_dev_open() call to the device will
fail until the device comes back up, thus preventing the above
deadlock.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
mlx4_ib_lock_cqs()/mlx4_ib_unlock_cqs() are helper functions that
lock/unlock both CQs attached to a QP in the proper order to avoid
AB-BA deadlocks. Annotate this so sparse can understand what's going
on (and warn us if we misuse these functions).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Replace open-coded reimplementations with printk_once().
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The ConnectX Programmer's Reference Manual states that the "SO" bit
must be set when posting Fast Register and Local Invalidate send work
requests. When this bit is set, the work request will be executed
only after all previous work requests on the send queue have been
executed. (If the bit is not set, Fast Register and Local Invalidate
WQEs may begin execution too early, which violates the defined
semantics for these operations)
This fixes the issue with NFS/RDMA reported in
<http://lists.openfabrics.org/pipermail/general/2009-April/059253.html>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The low-level mlx4 driver modified the page-list addresses for fast
register work requests post send to big-endian, and set a "present"
bit. This caused problems later when the consumer attempted to unmap
the pages using the page-list (using the list addresses which were
assumed to be still in CPU-endian order). Fix the mlx4 driver to
allocate two buffers and use a private buffer for the hardware-format
bus addresses.
This patch fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1571>,
an NFS/RDMA server crash. The cause of the crash was found by Vu Pham
of Mellanox. The fix is along the lines suggested by Steve Wise in
comment #21 in bug 1571.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The PAT work on x86 has finally made pgprot_writecombine() a usable API
for modular drivers. As the comment indicates, this is exactly what we
want to use in mlx4_ib to map BlueFlame pages up to userspace, since
using WC for these pages improves small message latency significantly.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
'mlx4', 'mthca', 'nes' and 'sysfs' into for-next
|
|
According to the ConnectX programmer's reference manual, all
operations should be stopped, all QPs should be torn down and all WQEs
flushed before the CLOSE_PORT command is invoked. In some cases
reversing the order of operations (as implemented now) could cause
a loss of completions.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When snooping a PortInfo MAD, its client_reregister bit is checked.
If the bit is ON then a CLIENT_REREGISTER event is dispatched,
otherwise a LID_CHANGE event is dispatched. This way of decision
ignores the cases where the MAD changes the LID along with an
instruction to reregister (so a necessary LID_CHANGE event won't be
dispatched) or the MAD is neither of these (and an unnecessary
LID_CHANGE event will be dispatched).
This causes problems at least with IPoIB, which will do a "light"
flush on reregister, rather than the "heavy" flush required due to a
LID change.
Fix this by dispatching a CLIENT_REREGISTER event if the
client_reregister bit is set, but also compare the LID in the MAD to
the current LID. If and only if they are not identical then a
LID_CHANGE event is dispatched.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The base versions handle constant folding just fine, use them
directly. The replacements are OK in the include/ files as they are
not exported to userspace so we don't need the __ prefixed versions.
This patch does not affect code generation at all.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The current work request posting code writes the LSO segment before
writing any data segments. This leaves a window where the LSO segment
overwrites the stamping in one cacheline that the HCA prefetches
before the rest of the cacheline is filled with the correct data
segments. When the HCA processes this work request, a local
protection error may result.
Fix this by saving the LSO header size field off and writing it only
after all data segments are written. This fix is a cleaned-up version
of a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1383>.
Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
