| Age | Commit message (Collapse) | Author |
|---|
|
The formula would yield -1 if the path is faster than the link, which
is wrong in a bad way (max throttling). Clamp to 0, which is the
correct value.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Wrong choice of port number caused modify_qp() to fail -- fixed.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The error codes for ib_post_send(), ib_post_recv(), and ib_post_srq_recv()
were inconsistent. Use EINVAL for too many SGEs and ENOMEM for too many
WRs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The wrong offset was being returned to libipathverbs so that when
ibv_modify_srq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch fixes the code which frees the partially allocated QP
resources if there was an error while creating the QP. In particular,
the QPN wasn't deallocated and the QP wasn't removed from the hash
table.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The wrong offset was being returned to libipathverbs so that when
ibv_resize_cq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The device attribute max_qp_init_rd_atom is not getting set in cxgb3's
query_device method. Version 1.0.4 of librdmacm now validates the
user's requested initiator and responder resources against the max
supported by the device. Since iw_cxgb3 wasn't setting this attribute
(and it defaulted to 0), all rdma_connect()s fail if there are
initiator resources requested by the app. Fix this by setting the
correct value in iwch_query_device().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The IPD (inter-packet delay) formula was a little off and assumed a
fixed physical link rate; fix the formula and query the actual
physical link rate, now that we can get it. Also, refactor the
calculation into a common function ehca_calc_ipd() and use that
instead of duplicating code.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Newer firmware versions return physical port information to the
partition, so hand that information to the consumer if it's present.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
When an ACK is received, the QP is removed from the timeout list and
then if there are still pending send WQEs, the QP is put back on the
timeout list. It is possible that another post send has put the QP on
the timeout list thus, a check needs to be made before trying to do it
again or the list is corrupted.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/fmr_pool: Stop ib_fmr threads from contributing to load average
IB/ipath: Fix incorrect use of sizeof on msg buffer (function argument)
IB/ipath: Limit length checksummed in eeprom
IB/ipath: Fix a race where s_last is updated without lock held
IB/mlx4: Lock SQ lock in mlx4_ib_post_send()
IPoIB/cm: Fix receive QP cleanup
|
|
Inside a function declared as
void foo(char bar[512])
the value of sizeof bar is the size of a pointer, not 512. So avoid
constructions like this by passing the size explicitly.
Also reduce the size of the buffer to 128 bytes (512 was overly generous).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The small eeprom that holds the GUID etc. contains a data-length, but if
the actual eeprom is new or has been erased, that byte will be 0xFF,
which is greater than the maximum physical length of the eeprom, and
more importantly greater than the length of the buffer we vmalloc'd.
Sanity-check the length to avoid the possbility of reading past end of
buffer.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
There is a small window where a send work queue entry could be
overwritten by ib_post_send() because s_last is updated before the
entry is read.
This patch closes the window by acquiring the lock and updating
the last send work queue entry index after reading the wr_id.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Because of a typo, mlx4_ib_post_send() takes the same lock rq.lock as
mlx4_ib_post_recv(). Correct the code so the intended sq.lock is
taken when posting a send.
Noticed by Yossi Leybovitch and pointed out by Jack Morgenstein from
Mellanox.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Increase command timeout for INIT_HCA to 10 seconds
IPoIB/cm: Use common CQ for CM send completions
IB/uverbs: Fix checking of userspace object ownership
IB/mlx4: Sanity check userspace send queue sizes
IPoIB: Rewrite "if (!likely(...))" as "if (unlikely(!(...)))"
IB/ehca: Enable large page MRs by default
IB/ehca: Change meaning of hca_cap_mr_pgsize
IB/ehca: Fix ehca_encode_hwpage_size() and alloc_fmr()
IB/ehca: Fix masking error in {,re}reg_phys_mr()
IB/ehca: Supply QP token for SRQ base QPs
IPoIB: Use round_jiffies() for ah_reap_task
RDMA/cma: Fix deadlock destroying listen requests
RDMA/cma: Add locking around QP accesses
IB/mthca: Avoid alignment traps when writing doorbells
mlx4_core: Kill mlx4_write64_raw()
|
|
More fallout from sg_page changes:
drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_set_pagebuf_user1':
drivers/infiniband/hw/ehca/ehca_mrmw.c:1779: error: 'struct scatterlist' has no member named 'page'
drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_check_kpages_per_ate':
drivers/infiniband/hw/ehca/ehca_mrmw.c:1835: error: 'struct scatterlist' has no member named 'page'
drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_set_pagebuf_user2':
drivers/infiniband/hw/ehca/ehca_mrmw.c:1870: error: 'struct scatterlist' has no member named 'page'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add sanity checks to send queue sizes passed in from userspace. The
minimum sq stride value below is taken from the MT25408 PRM (section
11.10, Table 306, log_sq_stride definition).
Without this check, userspace can submit arbitrarily large/small
values for the number of WQEs and the stride, which can crash the
kernel.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ehca_shca.hca_cap_mr_pgsize now contains all supported page sizes ORed
together. This makes some checks easier to code and understand, plus
we can return this value verbatim in query_hca(), fixing a problem
with SRP (reported by Anton Blanchard -- thanks!).
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Simplify ehca_encode_hwpage_size(), fixing an infinite loop for pgsize == 0
in the process. Fix the bug in alloc_fmr() that triggered the loop.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Because hardware reports the SRQ token in RWQEs of SRQ base QPs, supply the
base QP token as SRQ token, so we can properly find the SRQ base QP.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
eHEA drivers
Replace struct ibmebus_dev and struct ibmebus_driver with struct of_device
and struct of_platform_driver, respectively. Match the external ibmebus
interface and drivers using it.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Architectures such as ia64 see alignment traps when doing a 64-bit
read from __be32 doorbell[2] arrays to do doorbell writes in
mthca_write64(). Fix this by just passing the two halves of the
doorbell value into mthca_write64(). This actually improves the
generated code by allowing the compiler to see what's going on better.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits)
mlx4_core: Fix section mismatches
IPoIB: Allow setting policy to ignore multicast groups
IB/mthca: Mark error paths as unlikely() in post_srq_recv functions
IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.
IB/ipath: Remove redundant link state checks
IB/ipath: Fix IB_EVENT_PORT_ERR event
IB/ipath: Better handling of unexpected GPIO interrupts
IB/ipath: Maintain active time on all chips
IB/ipath: Fix QHT7040 serial number check
IB/ipath: Indicate a couple of chip bugs to userspace
IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround
IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close
IB/ipath: Remove duplicate copy of LMC
IB/ipath: Add ability to set the LMC via the sysfs debugging interface
IB/ipath: Optimize completion queue entry insertion and polling
IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED
IB/ipath: Generate flush CQE when QP is in error state
IB/ipath: Remove redundant code
IB/ipath: Future proof eeprom checksum code (contents reading)
IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate
...
|
|
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Fixed to be the same as everywhere else. copy and then zero the page *
in the array first, and then pass the copy to the VM routines.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch removes some redundant checks when the SMA changes the link
state since the same checks are made in the lower level function that
sets the state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The link state event calls were being generated when the SM told the SMA
to change link states. This works for IB_EVENT_PORT_ACTIVE but not if
the link goes down and stays down. The fix is to generate event calls
from the interrupt handler when the HW link state changes.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The General Purpose I/O pins can be configured to cause interrupts. At
the end of the interrupt code dealing with all known causes, a message
is output if any bits remain un-handled. Since this is a "can't happen"
scenario, it should only be triggered by bugs elsewhere. It is harmless,
and potentially beneficial, to limit the damage by masking any such
unexpected interrupts.
This patch adds disabling of interrupts from any pins that should
not have been allowed to interrupt, in addition to emitting a message.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
There is a count of "active hours" maintained in EEPROM, to aid
troubleshooting. The definition of "active" is based on traffic
exceeding a threshold in any given 5-second polling interval. As
originally written, the check was inadvertently bypassed for chips whose
counters were 64-bits wide, and only applied to chips with 32-bit wide
counters.
This patch moves the test for amount of traffic "out" to a more common
location, rather than depending on a side-effect of the software
emulation of 64-bit counts on chips whose hardware is only 32-bits wide.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Remove all the OEM and bringup boards, and complain and fail
initialization if one is found. QHT7040 with GPIO rework (128ywwuuuu)
is OK, older 112ywwuuuu is no longer supported). The check that had been
added was failing both the 112 and 128 series.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
A couple of chip bugs in the iba6110 and in the iba6120 are not in more
recent chips. This first bug swaps two of the pioavail register
locations. In the second bug, the chip can sometimes forget to dma the
pio avail register to memory. We indicate the presence of these bugs
with runtime flags and we indicate the presence of the flags by bumping
the SWMINOR.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
iba6110 rev3 and earlier had a chip bug where the chip could overrun the
recv header queue. rev4 fixed this chip bug so userspace no longer needs
to workaround it. Now we only set the workaround flag for older chip
versions.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
ipath_poll() suffered from a couple subtle bugs. Under the right
conditions we could leave recv interrupts enabled on an ipath user
context on close, thereby taking potentially unwanted interrupts on the
next open -- this is fixed by unconditionally turning off recv
interrupts on close. Also, we now use counters rather than set/clear
bits which allows us to make sure we catch all interrupts at the cost of
changing the semantics slightly (it's now give me all events since the
last time I called poll() rather than give me all events since I called
_this_ poll routine). We also added some memory barriers which may help
ensure we get all notifications in a timely manner.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The LMC value was being saved by the SMA in two places. This patch
cleans it up so only one copy is kept.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch adds the ability to set the LMC via a sysfs file as if the SM
sent a SubnSet(PortInfo) MAD. It is useful for debugging when no SM is
running.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The code to add an entry to the completion queue stored the QPN which is
needed for the user level verbs view of the completion queue entry but
the kernel struct ib_wc contains a pointer to the QP instead of a QPN.
When the kernel polled for a completion queue entry, the QPN was lookup
up and the QP pointer recovered. This patch stores the CQE differently
based on whether the CQ is a kernel CQ or a user CQ thus avoiding the
QPN to QP lookup overhead.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch implements the IB_EVENT_QP_LAST_WQE_REACHED event which is
needed by ib_ipoib to destroy the QP when used in connected mode.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Follow the IB spec. (C10-96) for post send which states that a flushed
completion event should be generated for work requests posted when a QP
is in the error state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch removes some redundant initialization code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
In an earlier change, the amount of data read from the flash was
mistakenly limited to the size known to the current driver. This causes
problems when the length is increased, and written with the new longer
version; the checksum would fail because not enough data was read.
Always read the full 128 byte length to prevent this.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
