| Age | Commit message (Collapse) | Author |
|---|
|
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (63 commits)
IB/qib: clean up properly if pci_set_consistent_dma_mask() fails
IB/qib: Allow driver to load if PCIe AER fails
IB/qib: Fix uninitialized pointer if CONFIG_PCI_MSI not set
IB/qib: Fix extra log level in qib_early_err()
RDMA/cxgb4: Remove unnecessary KERN_<level> use
RDMA/cxgb3: Remove unnecessary KERN_<level> use
IB/core: Add link layer type information to sysfs
IB/mlx4: Add VLAN support for IBoE
IB/core: Add VLAN support for IBoE
IB/mlx4: Add support for IBoE
mlx4_en: Change multicast promiscuous mode to support IBoE
mlx4_core: Update data structures and constants for IBoE
mlx4_core: Allow protocol drivers to find corresponding interfaces
IB/uverbs: Return link layer type to userspace for query port operation
IB/srp: Sync buffer before posting send
IB/srp: Use list_first_entry()
IB/srp: Reduce number of BUSY conditions
IB/srp: Eliminate two forward declarations
IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
IB: Replace EXTRA_CFLAGS with ccflags-y
...
|
|
Use the new {max,min}3 macros to save some cycles and bytes on the stack.
This patch substitutes trivial nested macros with their counterpart.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Joe Perches <joe@perches.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
'misc', 'mlx4', 'nes', 'qib' and 'srp' into for-next
|
|
srp_send_tsk_mgmt() was missing the proper DMA sync calls before posting
the buffer to the device.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Use the list_first_entry() macro in ib_srp instead of open-coding the equivalent,
which makes the source code slightly more descriptive. The list_first_entry()
macro itself was introduced in kernel 2.6.22.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
As proposed by the SRP (draft) standard, ib_srp reserves one ring
element for SRP_TSK_MGMT requests. This patch makes sure that the SCSI
mid-layer never tries to queue more than (SRP request limit) - 1 SCSI
commands to ib_srp. This improves performance for targets whose request
limit is less than or equal to SRP_NORMAL_REQ_SQ_SIZE by reducing the
number of BUSY responses reported by ib_srp to the SCSI mid-layer.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Use the net device's dev_id field to encode the port number of the pci
device. This can be used to to associate a net device with the pci
device's port. The encoding is: dev_id = port - 1.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
This patch adds support for SRP_CRED_REQ to avoid a lockup by targets
that use that mechanism to return credits to the initiator. This
prevents a lockup observed in the field where we would never add the
credits from the SRP_CRED_REQ to our current count, and would therefore
never send another command to the target.
Minimal support for SRP_AER_REQ is also added, as these messages can
also be used to convey additional credits to the initiator.
Based upon extensive debugging and code by Bart Van Assche and a bug
report by Chris Worley.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The transmit ring in ib_srp (srp_target.tx_ring) is currently only used
for allocating requests sent by the initiator to the target. This patch
prepares using that ring for allocation of both requests and responses.
Also, this patch differentiates the uses of SRP_SQ_SIZE, increases the
size of the IB send completion queue by one element and reserves one
transmit ring slot for SRP_TSK_MGMT requests.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
IPoIB is IP-over-Infiniband link layer. In the case of IBoE, the link
layer is Ethernet and IP can work directly over Ethernet, so disable
IPoIB for non-IB_LINK_LAYER_INFINIBAND ports.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
IGMP processing is broken because the IPOIB does not set the
skb->pkt_type the right way for multicast traffic. All incoming
packets are set to PACKET_HOST which means that igmp_recv() will
ignore the IGMP broadcasts/multicasts.
This in turn means that the IGMP timers are firing and are sending
information about multicast subscriptions unnecessarily. In a large
private network this can cause traffic spikes.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (42 commits)
IB/qib: Add missing <linux/slab.h> include
IB/ehca: Drop unnecessary NULL test
RDMA/nes: Fix confusing if statement indentation
IB/ehca: Init irq tasklet before irq can happen
RDMA/nes: Fix misindented code
RDMA/nes: Fix showing wqm_quanta
RDMA/nes: Get rid of "set but not used" variables
RDMA/nes: Read firmware version from correct place
IB/srp: Export req_lim via sysfs
IB/srp: Make receive buffer handling more robust
IB/srp: Use print_hex_dump()
IB: Rename RAW_ETY to RAW_ETHERTYPE
RDMA/nes: Fix two sparse warnings
RDMA/cxgb3: Make needlessly global iwch_l2t_send() static
IB/iser: Make needlessly global iser_alloc_rx_descriptors() static
RDMA/cxgb4: Add timeouts when waiting for FW responses
IB/qib: Fix race between qib_error_qp() and receive packet processing
IB/qib: Limit the number of packets processed per interrupt
IB/qib: Allow writes to the diag_counters to be able to clear them
IB/qib: Set cfgctxts to number of CPUs by default
...
|
|
'srp' into for-next
|
|
Export req_lim via sysfs for debugging.
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
|
|
The current strategy in ib_srp for posting receive buffers is:
* Post one buffer after channel establishment.
* Post one buffer before sending an SRP_CMD or SRP_TSK_MGMT to the target.
As a result, only the first non-SRP_RSP information unit from the
target will be processed. If that first information unit is an
SRP_T_LOGOUT, it will be processed. On the other hand, if the
initiator receives an SRP_CRED_REQ or SRP_AER_REQ before it receives a
SRP_T_LOGOUT, the SRP_T_LOGOUT won't be processed.
We can fix this inconsistency by changing the strategy for posting
receive buffers to:
* Post all receive buffers after channel establishment.
* After a receive buffer has been consumed and processed, post it again.
A side effect is that the ib_post_recv() call is moved out of the SCSI
command processing path. Since __srp_post_recv() is not called
directly any more, get rid of it and move the code directly into
srp_post_recv(). Also, move srp_post_recv() up in the file to avoid a
forward declaration.
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Replace an open-coded dump of the receive buffer with a call to
print_hex_dump().
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Sumeet Lahorani <sumeet.lahorani@oracle.com> reported that the IPoIB
child entries are world-writable; however we don't want ordinary users
to be able to create and destroy child interfaces, so fix them to be
writable only by root.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Following commit 1437ce3983bcbc0447a0dedcd644c14fe833d266 "ethtool:
Change ethtool_op_set_flags to validate flags", ethtool_op_set_flags
takes a third parameter and cannot be used directly as an
implementation of ethtool_ops::set_flags.
Changes nes and ipoib driver to pass in the appropriate value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
|
|
'masked-atomics', 'misc', 'mthca' and 'nes' into for-next
|
|
We shouldn't free things here because we free them later.
The call tree looks like this:
iser_connect() ==> initiating the connection establishment
and later
iser_cma_handler() => iser_route_handler() => iser_create_ib_conn_res()
if we fail here, eventually iser_conn_release() is called, resulting
in a double free.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The iser connection teardown flow isn't over until the underlying
Connection Manager (e.g the IB CM) delivers a disconnected or timeout
event through the RDMA-CM. When the remote (target) side isn't
reachable, e.g when some HW e.g port/hca/switch isn't functioning or
taken down administratively, the CM timeout flow is used and the event
may be generated only after relatively long time -- on the order of
tens of seconds.
The current iser code exposes this possibly long delay to higher
layers, specifically to the iscsid daemon and iscsi kernel stack. As a
result, the iscsi stack doesn't respond well: this low-level CM delay
is added to the fail-over time under HA schemes such as the one
provided by DM multipath through the multipathd(8) service.
This patch enhances the reference counting scheme on iser's IB
connections so that the disconnect flow initiated by iscsid from user
space (ep_disconnect) doesn't wait for the CM to deliver the
disconnect/timeout event. (The connection teardown isn't done from
iser's view point until the event is delivered)
The iser ib (rdma) connection object is destroyed when its reference
count reaches zero. When this happens on the RDMA-CM callback
context, extra care is taken so that the RDMA-CM does the actual
destroying of the associated ID, since doing it in the callback is
prohibited.
The reference count of iser ib connection normally reaches three,
where the <ref, deref> relations are
1. conn <init, terminate>
2. conn <bind, stop/destroy>
3. cma id <create, disconnect/error/timeout callbacks>
With this patch, multipath fail-over time is about 30 seconds, while
without this patch, multipath fail-over time is about 130 seconds.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The iscsi connection object life cycle includes binding and unbinding
(conn_stop) to/from the iscsi transport connection object. Since
iscsi connection objects are recycled, at the time the transport
connection (e.g iser's IB connection) is released, it is not valid to
touch the iscsi connection tied to the transport back-pointer since it
may already point to a different transport connection.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Add handler to handle events such as port up and down. This is useful
when testing high-availability schemes such as multi-pathing.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/stmmac/stmmac_main.c
drivers/net/wireless/wl12xx/wl1271_cmd.c
drivers/net/wireless/wl12xx/wl1271_main.c
drivers/net/wireless/wl12xx/wl1271_spi.c
net/core/ethtool.c
net/mac80211/scan.c
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/via-velocity.c
drivers/net/wireless/iwlwifi/iwl-agn.c
|
|
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
Finally this bit can be removed. Currently, after the bonding driver is
changed/fixed (32a806c194ea112cfab00f558482dd97bee5e44e net-next-2.6),
that's not possible for an addr with different length than dev->addr_len
to be present in list. Removing this check as in new mc_list there will be
no addrlen in the record.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (69 commits)
[SCSI] scsi_transport_fc: Fix synchronization issue while deleting vport
[SCSI] bfa: Update the driver version to 2.1.2.1.
[SCSI] bfa: Remove unused header files and did some cleanup.
[SCSI] bfa: Handle SCSI IO underrun case.
[SCSI] bfa: FCS and include file changes.
[SCSI] bfa: Modified the portstats get/clear logic
[SCSI] bfa: Replace bfa_get_attr() with specific APIs
[SCSI] bfa: New portlog entries for events (FIP/FLOGI/FDISC/LOGO).
[SCSI] bfa: Rename pport to fcport in BFA FCS.
[SCSI] bfa: IOC fixes, check for IOC down condition.
[SCSI] bfa: In MSIX mode, ignore spurious RME interrupts when FCoE ports are in FW mismatch state.
[SCSI] bfa: Fix Command Queue (CPE) full condition check and ack CPE interrupt.
[SCSI] bfa: IOC recovery fix in fcmode.
[SCSI] bfa: AEN and byte alignment fixes.
[SCSI] bfa: Introduce a link notification state machine.
[SCSI] bfa: Added firmware save clear feature for BFA driver.
[SCSI] bfa: FCS authentication related changes.
[SCSI] bfa: PCI VPD, FIP and include file changes.
[SCSI] bfa: Fix to copy fpma MAC when requested by user space application.
[SCSI] bfa: RPORT state machine: direct attach mode fix.
...
|
|
Print the return code of ib_post_send() if it fails to make these
debugging messages more useful.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The IPoIB UD QP reports send completions to priv->send_cq, which is
usually left unarmed; it only gets armed when the number of
outstanding send requests reaches the size of the TX queue. This
arming is done only in the send path for the UD QP. However, when
sending CM packets, the net queue may be stopped for the same reasons
but no measures are taken to recover the UD path from a lockup.
Consider this scenario: a host sends high rate of both CM and UD
packets, with a TX queue length of N. If at some time the number of
outstanding UD packets is more than N/2 and the overall outstanding
packets is N-1, and CM sends a packet (making the number of
outstanding sends equal N), the TX queue will be stopped. When all
the CM packets complete, the number of outstanding packets will still
be higher than N/2 so the TX queue will not be restarted.
Fix this by calling ib_req_notify_cq() when the queue is stopped in
the CM path.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (48 commits)
IB/srp: Clean up error path in srp_create_target_ib()
IB/srp: Split send and recieve CQs to reduce number of interrupts
RDMA/nes: Add support for KR device id 0x0110
IB/uverbs: Use anon_inodes instead of private infinibandeventfs
IB/core: Fix and clean up ib_ud_header_init()
RDMA/cxgb3: Mark RDMA device with CXIO_ERROR_FATAL when removing
RDMA/cxgb3: Don't allocate the SW queue for user mode CQs
RDMA/cxgb3: Increase the max CQ depth
RDMA/cxgb3: Doorbell overflow avoidance and recovery
IB/core: Pack struct ib_device a little tighter
IB/ucm: Clean whitespace errors
IB/ucm: Increase maximum devices supported
IB/ucm: Use stack variable 'base' in ib_ucm_add_one
IB/ucm: Use stack variable 'devnum' in ib_ucm_add_one
IB/umad: Clean whitespace
IB/umad: Increase maximum devices supported
IB/umad: Use stack variable 'base' in ib_umad_init_port
IB/umad: Use stack variable 'devnum' in ib_umad_init_port
IB/umad: Remove port_table[]
IB/umad: Convert *cdev to cdev in struct ib_umad_port
...
|
|
The iscsi_eh_target_reset has been modified to attempt
target reset only. If it fails, then iscsi_eh_session_reset
will be called.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
Instead of repeating the error unwinding steps in each place an error
can be detected, use the common idiom of gotos into an error flow.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
We can reduce the number of IB interrupts from two interrupts per
srp_queuecommand() call to one by using separate CQs for send and
receive completions and processing send completions by polling every
time a TX IU is allocated.
Receive completion events still trigger an interrupt.
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Apparently bogus mc address can break IPOIB multicast processing. Therefore
returning the check for addrlen back until this is resolved in bonding (I don't
see any other point from where mc address with non-dev->addr_len length can came
from).
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to the loop complexicity in nes_nic.c, I'm using char* to copy mc addresses
to it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the iSER receive completion flow takes the session lock
twice. Optimize it to avoid the first one by letting
iser_task_rdma_finalize() be called only from the cleanup_task
callback invoked by iscsi_free_task, thus reducing the contention on
the session lock between the scsi command submission to the scsi
command completion flows.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
libiscsi passthrough mode invokes the transport xmit calls directly
without first going through an internal queue, unlike the other mode,
which uses a queue and a xmitworker thread. Now that the "cant_sleep"
prerequisite of iscsi_host_alloc is met, move to use it. Handling
xmit errors is now done by the passthrough flow of libiscsi. Since
the queue/worker aren't used in this mode, the code that schedules the
xmitworker is removed.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Remove unnecessary checks for the IB connection state and for QP
overflow, as conn state changes are reported by iSER to libiscsi and
handled there. QP overflow is theoretically possible only when
unsolicited data-outs are used; anyway it's being checked and handled
by HW drivers.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Two minor flows in iSER's data path still use allocations; move them
to be atomic as a preperation step towards moving to use libiscsi
passthrough mode.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
