| Age | Commit message (Collapse) | Author |
|---|
|
Some manual fixups required due to clashes with the PF_FREEZE cleanups.
|
|
drivers/s390/block/dcssblk.c: update device attribute callbacks
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
It looks like logic for enabling hardware tapping in ALPS driver was
inverted and we enable it only if it was already enabled by BIOS or
firmware.
I have a confirmation from one user that the patch below fixes the problem
for him and it might be beneficial if we could get it into 2.6.12.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
to allow easy switching at run-time.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
given number of bytes from device. Change ps2_command to
allow using 0 as command ID and actually pass it to the
device instead of working as a drain.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
operations do not iterfere with each other.
Also make sure that serio core takes serio->drv_sem
not only for connect/disconnect but for reconnect
too.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
I have an Ahtec laptop with a ALPS GlidePoint device, with 4 buttons.
With Linux hernel 2.6.12rc4 and rc5 I'm unable to use the vertical
scroll buttons (BACK and FORWARD).
BACK gets detected as BTN_MIDDLE and FORWARD is undetected.
I've modified the drivers/input/mouse/alps.c from 2.6.12rc5 and now it
works fine!
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
compared to "classic" PS/2 mice, provide appropriate
resolution setting handler.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
the rest of protocols in preparation to dynamic protocol
switching.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
- do not try to set rate and resolution in init method, let
psmouse core do it for us. This also removes special quirks
from the core;
- do not disable mouse before doing full reset - meaningless;
- some formatting and whitespace cleanups.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
From: Kenan Esau <kenan.esau@conan.de>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
core takes care of calling open and close methods only
when needed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
is no reason one driver should take 10 lines in dmesg.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
sends an incorrect ID and wasn't recognized.
Reported-by: Stefan Seyfried <seife@suse.de>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
ALPS needs to be reset for detection to work reliably when reconnecting.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make the alps printk output look consistent.
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
