| Age | Commit message (Collapse) | Author |
|---|
|
Pull md fixes from Neil Brown:
"Two bugfixes for md
both tagged for -stable"
* tag 'md/3.14-fixes' of git://neil.brown.name/md:
md/raid5: Fix CPU hotplug callback registration
md/raid1: restore ability for check and repair to fix read errors.
|
|
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Interestingly, the raid5 code can actually prevent double initialization and
hence can use the following simplified form of callback registration:
register_cpu_notifier(&foobar_cpu_notifier);
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
put_online_cpus();
A hotplug operation that occurs between registering the notifier and calling
get_online_cpus(), won't disrupt anything, because the code takes care to
perform the memory allocations only once.
So reorganize the code in raid5 this way to fix the deadlock with callback
registration.
Cc: linux-raid@vger.kernel.org
Cc: stable@vger.kernel.org (v2.6.32+)
Fixes: 36d1c6476be51101778882897b315bd928c8c7b5
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
[Srivatsa: Fixed the unregister_cpu_notifier() deadlock, added the
free_scratch_buffer() helper to condense code further and wrote the changelog.]
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit 30bc9b53878a9921b02e3b5bc4283ac1c6de102a
md/raid1: fix bio handling problems in process_checks()
Move the bio_reset() to a point before where BIO_UPTODATE is checked,
so that check now always report that the bio is uptodate, even if it is not.
This causes process_check() to sometimes treat read-errors as
successful matches so the good data isn't written out.
This patch preserves the flag until it is needed.
Bug was introduced in 3.11, but backported to 3.10-stable (as it fixed
an even worse bug). So suitable for any -stable since 3.10.
Reported-and-tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: stable@vger.kernel.org (3.10+)
Fixed: 30bc9b53878a9921b02e3b5bc4283ac1c6de102a
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
into for-linus
|
|
Pull block IO driver changes from Jens Axboe:
- bcache update from Kent Overstreet.
- two bcache fixes from Nicholas Swenson.
- cciss pci init error fix from Andrew.
- underflow fix in the parallel IDE pg_write code from Dan Carpenter.
I'm sure the 1 (or 0) users of that are now happy.
- two PCI related fixes for sx8 from Jingoo Han.
- floppy init fix for first block read from Jiri Kosina.
- pktcdvd error return miss fix from Julia Lawall.
- removal of IRQF_SHARED from the SEGA Dreamcast CD-ROM code from
Michael Opdenacker.
- comment typo fix for the loop driver from Olaf Hering.
- potential oops fix for null_blk from Raghavendra K T.
- two fixes from Sam Bradshaw (Micron) for the mtip32xx driver, fixing
an OOM problem and a problem with handling security locked conditions
* 'for-3.14/drivers' of git://git.kernel.dk/linux-block: (47 commits)
mg_disk: Spelling s/finised/finished/
null_blk: Null pointer deference problem in alloc_page_buffers
mtip32xx: Correctly handle security locked condition
mtip32xx: Make SGL container per-command to eliminate high order dma allocation
drivers/block/loop.c: fix comment typo in loop_config_discard
drivers/block/cciss.c:cciss_init_one(): use proper errnos
drivers/block/paride/pg.c: underflow bug in pg_write()
drivers/block/sx8.c: remove unnecessary pci_set_drvdata()
drivers/block/sx8.c: use module_pci_driver()
floppy: bail out in open() if drive is not responding to block0 read
bcache: Fix auxiliary search trees for key size > cacheline size
bcache: Don't return -EINTR when insert finished
bcache: Improve bucket_prio() calculation
bcache: Add bch_bkey_equal_header()
bcache: update bch_bkey_try_merge
bcache: Move insert_fixup() to btree_keys_ops
bcache: Convert sorting to btree_keys
bcache: Convert debug code to btree_keys
bcache: Convert btree_iter to struct btree_keys
bcache: Refactor bset_tree sysfs stats
...
|
|
Pull core block IO changes from Jens Axboe:
"The major piece in here is the immutable bio_ve series from Kent, the
rest is fairly minor. It was supposed to go in last round, but
various issues pushed it to this release instead. The pull request
contains:
- Various smaller blk-mq fixes from different folks. Nothing major
here, just minor fixes and cleanups.
- Fix for a memory leak in the error path in the block ioctl code
from Christian Engelmayer.
- Header export fix from CaiZhiyong.
- Finally the immutable biovec changes from Kent Overstreet. This
enables some nice future work on making arbitrarily sized bios
possible, and splitting more efficient. Related fixes to immutable
bio_vecs:
- dm-cache immutable fixup from Mike Snitzer.
- btrfs immutable fixup from Muthu Kumar.
- bio-integrity fix from Nic Bellinger, which is also going to stable"
* 'for-3.14/core' of git://git.kernel.dk/linux-block: (44 commits)
xtensa: fixup simdisk driver to work with immutable bio_vecs
block/blk-mq-cpu.c: use hotcpu_notifier()
blk-mq: for_each_* macro correctness
block: Fix memory leak in rw_copy_check_uvector() handling
bio-integrity: Fix bio_integrity_verify segment start bug
block: remove unrelated header files and export symbol
blk-mq: uses page->list incorrectly
blk-mq: use __smp_call_function_single directly
btrfs: fix missing increment of bi_remaining
Revert "block: Warn and free bio if bi_end_io is not set"
block: Warn and free bio if bi_end_io is not set
blk-mq: fix initializing request's start time
block: blk-mq: don't export blk_mq_free_queue()
block: blk-mq: make blk_sync_queue support mq
block: blk-mq: support draining mq queue
dm cache: increment bi_remaining when bi_end_io is restored
block: fixup for generic bio chaining
block: Really silence spurious compiler warnings
block: Silence spurious compiler warnings
block: Kill bio_pair_split()
...
|
|
Signed-off-by: Nicholas Swenson <nks@daterainc.com>
|
|
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
|
|
The BUG_ON at the end of __bch_btree_mark_key can be triggered due to
an integer overflow error:
BITMASK(GC_SECTORS_USED, struct bucket, gc_mark, 2, 13);
...
SET_GC_SECTORS_USED(g, min_t(unsigned,
GC_SECTORS_USED(g) + KEY_SIZE(k),
(1 << 14) - 1));
BUG_ON(!GC_SECTORS_USED(g));
In bcache.h, the SECTORS_USED bitfield is defined to be 13 bits wide.
While the SET_ code tries to ensure that the field doesn't overflow by
clamping it to (1<<14)-1 == 16383, this is incorrect because 16383
requires 14 bits. Therefore, if GC_SECTORS_USED() + KEY_SIZE() =
8192, the SET_ statement tries to store 8192 into a 13-bit field. In
a 13-bit field, 8192 becomes zero, thus triggering the BUG_ON.
Therefore, create a field width constant and a max value constant, and
use those to create the bitfield and check the inputs to
SET_GC_SECTORS_USED. Arguably the BITMASK() template ought to have
BUG_ON checks for too-large values, but that's a separate patch.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Pull md updates from Neil Brown:
"All bug fixes, two tagged for -stable"
* tag 'md/3.14' of git://neil.brown.name/md:
md/raid5: close recently introduced race in stripe_head management.
md/raid5: fix long-standing problem with bitmap handling on write failure.
md: check command validity early in md_ioctl().
md: ensure metadata is writen after raid level change.
md/raid10: avoid fullsync when not necessary.
md: allow a partially recovered device to be hot-added to an array.
md: Change handling of save_raid_disk and metadata update during recovery.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper changes from Mike Snitzer:
"A lot of attention was paid to improving the thin-provisioning
target's handling of metadata operation failures and running out of
space. A new 'error_if_no_space' feature was added to allow users to
error IOs rather than queue them when either the data or metadata
space is exhausted.
Additional fixes/features include:
- a few fixes to properly support thin metadata device resizing
- a solution for reliably waiting for a DM device's embedded kobject
to be released before destroying the device
- old dm-snapshot is updated to use the dm-bufio interface to take
advantage of readahead capabilities that improve snapshot
activation
- new dm-cache target tunables to control how quickly data is
promoted to the cache (fast) device
- improved write efficiency of cluster mirror target by combining
userspace flush and mark requests"
* tag 'dm-3.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (35 commits)
dm log userspace: allow mark requests to piggyback on flush requests
dm space map metadata: fix bug in resizing of thin metadata
dm cache: add policy name to status output
dm thin: fix pool feature parsing
dm sysfs: fix a module unload race
dm snapshot: use dm-bufio prefetch
dm snapshot: use dm-bufio
dm snapshot: prepare for switch to using dm-bufio
dm snapshot: use GFP_KERNEL when initializing exceptions
dm cache: add block sizes and total cache blocks to status output
dm btree: add dm_btree_find_lowest_key
dm space map metadata: fix extending the space map
dm space map common: make sure new space is used during extend
dm: wait until embedded kobject is released before destroying a device
dm: remove pointless kobject comparison in dm_get_from_kobject
dm snapshot: call destroy_work_on_stack() to pair with INIT_WORK_ONSTACK()
dm cache policy mq: introduce three promotion threshold tunables
dm cache policy mq: use list_del_init instead of list_del + INIT_LIST_HEAD
dm thin: fix set_pool_mode exposed pool operation races
dm thin: eliminate the no_free_space flag
...
|
|
In the cluster evironment, cluster write has poor performance because
userspace_flush() has to contact a userspace program (cmirrord) for
clear/mark/flush requests. But both mark and flush requests require
cmirrord to communicate the message to all the cluster nodes for each
flush call. This behaviour is really slow.
To address this we now merge mark and flush requests together to reduce
the kernel-userspace-kernel time. We allow a new directive,
"integrated_flush" that can be used to instruct the kernel log code to
combine flush and mark requests when directed by userspace. If not
directed by userspace (due to an older version of the userspace code
perhaps), the kernel will function as it did previously - preserving
backwards compatibility. Additionally, flush requests are performed
lazily when only clear requests exist.
Signed-off-by: Dongmao Zhang <dmzhang@suse.com>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
"The bulk of changes are cleanups and preparations for the upcoming
kernfs conversion.
- cgroup_event mechanism which is and will be used only by memcg is
moved to memcg.
- pidlist handling is updated so that it can be served by seq_file.
Also, the list is not sorted if sane_behavior. cgroup
documentation explicitly states that the file is not sorted but it
has been for quite some time.
- All cgroup file handling now happens on top of seq_file. This is
to prepare for kernfs conversion. In addition, all operations are
restructured so that they map 1-1 to kernfs operations.
- Other cleanups and low-pri fixes"
* 'for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (40 commits)
cgroup: trivial style updates
cgroup: remove stray references to css_id
doc: cgroups: Fix typo in doc/cgroups
cgroup: fix fail path in cgroup_load_subsys()
cgroup: fix missing unlock on error in cgroup_load_subsys()
cgroup: remove for_each_root_subsys()
cgroup: implement for_each_css()
cgroup: factor out cgroup_subsys_state creation into create_css()
cgroup: combine css handling loops in cgroup_create()
cgroup: reorder operations in cgroup_create()
cgroup: make for_each_subsys() useable under cgroup_root_mutex
cgroup: css iterations and css_from_dir() are safe under cgroup_mutex
cgroup: unify pidlist and other file handling
cgroup: replace cftype->read_seq_string() with cftype->seq_show()
cgroup: attach cgroup_open_file to all cgroup files
cgroup: generalize cgroup_pidlist_open_file
cgroup: unify read path so that seq_file is always used
cgroup: unify cgroup_write_X64() and cgroup_write_string()
cgroup: remove cftype->read(), ->read_map() and ->write()
hugetlb_cgroup: convert away from cftype->read()
...
|
|
As release_stripe and __release_stripe decrement ->count and then
manipulate ->lru both under ->device_lock, it is important that
get_active_stripe() increments ->count and clears ->lru also under
->device_lock.
However we currently list_del_init ->lru under the lock, but increment
the ->count outside the lock. This can lead to races and list
corruption.
So move the atomic_inc(&sh->count) up inside the ->device_lock
protected region.
Note that we still increment ->count without device lock in the case
where get_free_stripe() was called, and in fact don't take
->device_lock at all in that path.
This is safe because if the stripe_head can be found by
get_free_stripe, then the hash lock assures us the no-one else could
possibly be calling release_stripe() at the same time.
Fixes: 566c09c53455d7c4f1130928ef8071da1a24ea65
Cc: stable@vger.kernel.org (3.13)
Reported-and-tested-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
This bug was introduced in commit 7e664b3dec431e ("dm space map metadata:
fix extending the space map").
When extending a dm-thin metadata volume we:
- Switch the space map into a simple bootstrap mode, which allocates
all space linearly from the newly added space.
- Add new bitmap entries for the new space
- Increment the reference counts for those newly allocated bitmap
entries
- Commit changes to disk
- Switch back out of bootstrap mode.
But, the disk commit may allocate space itself, if so this fact will be
lost when switching out of bootstrap mode.
The bug exhibited itself as an error when the bitmap_root, with an
erroneous ref count of 0, was subsequently decremented as part of a
later disk commit. This would cause the disk commit to fail, and thinp
to enter read_only mode. The metadata was not damaged (thin_check
passed).
The fix is to put the increments + commit into a loop, running until
the commit has not allocated extra space. In practise this loop only
runs twice.
With this fix the following device mapper testsuite test passes:
dmtest run --suite thin-provisioning -n thin_remove_works_after_resize
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # depends on commit 7e664b3dec431e
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / sysfs patches from Greg KH:
"Here's the big driver core and sysfs patch set for 3.14-rc1.
There's a lot of work here moving sysfs logic out into a "kernfs" to
allow other subsystems to also have a virtual filesystem with the same
attributes of sysfs (handle device disconnect, dynamic creation /
removal as needed / unneeded, etc)
This is primarily being done for the cgroups filesystem, but the goal
is to also move debugfs to it when it is ready, solving all of the
known issues in that filesystem as well. The code isn't completed
yet, but all should be stable now (there is a big section that was
reverted due to problems found when testing)
There's also some other smaller fixes, and a driver core addition that
allows for a "collection" of objects, that the DRM people will be
using soon (it's in this tree to make merges after -rc1 easier)
All of this has been in linux-next with no reported issues"
* tag 'driver-core-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (113 commits)
kernfs: associate a new kernfs_node with its parent on creation
kernfs: add struct dentry declaration in kernfs.h
kernfs: fix get_active failure handling in kernfs_seq_*()
Revert "kernfs: fix get_active failure handling in kernfs_seq_*()"
Revert "kernfs: replace kernfs_node->u.completion with kernfs_root->deactivate_waitq"
Revert "kernfs: remove KERNFS_ACTIVE_REF and add kernfs_lockdep()"
Revert "kernfs: remove KERNFS_REMOVED"
Revert "kernfs: restructure removal path to fix possible premature return"
Revert "kernfs: invoke kernfs_unmap_bin_file() directly from __kernfs_remove()"
Revert "kernfs: remove kernfs_addrm_cxt"
Revert "kernfs: make kernfs_get_active() block if the node is deactivated but not removed"
Revert "kernfs: implement kernfs_{de|re}activate[_self]()"
Revert "kernfs, sysfs, driver-core: implement kernfs_remove_self() and its wrappers"
Revert "pci: use device_remove_file_self() instead of device_schedule_callback()"
Revert "scsi: use device_remove_file_self() instead of device_schedule_callback()"
Revert "s390: use device_remove_file_self() instead of device_schedule_callback()"
Revert "sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()"
Revert "kernfs: remove unnecessary NULL check in __kernfs_remove()"
kernfs: remove unnecessary NULL check in __kernfs_remove()
drivers/base: provide an infrastructure for componentised subsystems
...
|
|
The cache's policy may have been established using the "default" alias,
which is currently the "mq" policy but the default policy may change in
the future. It is useful to know exactly which policy is being used.
Add a 'real' member to the dm_cache_policy_type structure and have the
"default" dm_cache_policy_type point to the real "mq"
dm_cache_policy_type. Update dm_cache_policy_get_name() to check if
real is set, if so report the name of the real policy (not the alias).
Requested-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Commit 787a996cb251e20 ("dm thin: add error_if_no_space feature")
mistakenly forgot to increase the number of feature args supported.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Before a write starts we set a bit in the write-intent bitmap.
When the write completes we clear that bit if the write was successful
to all devices. However if the write wasn't fully successful we
should not clear the bit. If the faulty drive is subsequently
re-added, the fact that the bit is still set ensure that we will
re-write the data that is missing.
This logic is mediated by the STRIPE_DEGRADED flag - we only clear the
bitmap bit when this flag is not set.
Currently we correctly set the flag if a write starts when some
devices are failed or missing. But we do *not* set the flag if some
device failed during the write attempt.
This is wrong and can result in clearing the bit inappropriately.
So: set the flag when a write fails.
This bug has been present since bitmaps were introduces, so the fix is
suitable for any -stable kernel.
Reported-by: Ethan Wilson <ethan.wilson@shiftmail.org>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Verify that the cmd parameter passed to md_ioctl() is valid before
doing anything.
This fixes mddev->hold_active being set to 0 when an invalid ioctl
command is passed to md_ioctl() before the array has been configured.
Clearing mddev->hold_active in that case can lead to a livelock
situation when an invalid ioctl number is given to md_ioctl() by a
process when the mddev is currently being opened by another process:
Process 1 Process 2
--------- ---------
md_alloc()
mddev_find()
-> returns a new mddev with
hold_active == UNTIL_IOCTL
add_disk()
-> sends KOBJ_ADD uevent
(sees KOBJ_ADD uevent for device)
md_open()
md_ioctl(INVALID_IOCTL)
-> returns ENODEV and clears
mddev->hold_active
md_release()
md_put()
-> deletes the mddev as
hold_active is 0
md_open()
mddev_find()
-> returns a newly
allocated mddev with
mddev->gendisk == NULL
-> returns with ERESTARTSYS
(kernel restarts the open syscall)
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Pull late md fixes from Neil Brown:
"Half a dozen md bug fixes.
All of these fix real bugs the people have hit, and are tagged for
-stable. Sorry they are late .... Christmas holidays and all that.
Hopefully they can still squeak into 3.13"
* tag 'md/3.13-fixes' of git://neil.brown.name/md:
md: fix problem when adding device to read-only array with bitmap.
md/raid10: fix bug when raid10 recovery fails to recover a block.
md/raid5: fix a recently broken BUG_ON().
md/raid1: fix request counting bug in new 'barrier' code.
md/raid10: fix two bugs in handling of known-bad-blocks.
md/raid5: Fix possible confusion when multiple write errors occur.
|
|
This reverts commit be35f48610 ("dm: wait until embedded kobject is
released before destroying a device") and provides an improved fix.
The kobject release code that calls the completion must be placed in a
non-module file, otherwise there is a module unload race (if the process
calling dm_kobject_release is preempted and the DM module unloaded after
the completion is triggered, but before dm_kobject_release returns).
To fix this race, this patch moves the completion code to dm-builtin.c
which is always compiled directly into the kernel if BLK_DEV_DM is
selected.
The patch introduces a new dm_kobject_holder structure, its purpose is
to keep the completion and kobject in one place, so that it can be
accessed from non-module code without the need to export the layout of
struct mapped_device to that code.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
This patch modifies dm-snapshot so that it prefetches the buffers when
loading the exceptions.
The number of buffers read ahead is specified in the DM_PREFETCH_CHUNKS
macro. The current value for DM_PREFETCH_CHUNKS (12) was found to
provide the best performance on a single 15k SCSI spindle. In the
future we may modify this default or make it configurable.
Also, introduce the function dm_bufio_set_minimum_buffers to setup
bufio's number of internal buffers before freeing happens. dm-bufio may
hold more buffers if enough memory is available. There is no guarantee
that the specified number of buffers will be available - if you need a
guarantee, use the argument reserved_buffers for
dm_bufio_client_create.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Use dm-bufio for initial loading of the exceptions.
Introduce a new function dm_bufio_forget that frees the given buffer.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Change the functions get_exception, read_exception and insert_exceptions
so that ps->area is passed as an argument.
This patch doesn't change any functionality, but it refactors the code
to allow for a cleaner switch over to using dm-bufio.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The list of initial exceptions is loaded in the target constructor. We
are allowed to allocate memory with GFP_KERNEL at this point. So,
change alloc_completed_exception to use GFP_KERNEL when being called
from the constructor.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
level_store() currently does not make sure the metadata is
updates to reflect the new raid level. It simply sets MD_CHANGE_DEVS.
Any level with a ->thread will quickly notice this and update the
metadata. However RAID0 and Linear do not have a thread so no
metadata update happens until the array is stopped. At that point the
metadata is written.
This is later that we would like. While the delay doesn't risk any
data it can cause confusion. So if there is no md thread, immediately
update the metadata after a level change.
Reported-by: Richard Michael <rmichael@edgeofthenet.org>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
This is the raid10 equivalent of
commit 4f0a5e012cf41321d611e7cad63e1017d143d138
MD RAID1: Further conditionalize 'fullsync'
If a device in a newly assembled array is not fully recovered we
currently do a fully resync by don't need to.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When adding a new device into an array it is normally important to
clear any stale data from ->recovery_offset else the new device may
not be recovered properly.
However when re-adding a device which is known to be nearly in-sync,
this is not needed and can be detrimental. The (bitmap-based)
resync will still happen, and further recovery is only needed from
where-ever it was already up to.
So if save_raid_disk is set, signifying a re-add, don't clear
->recovery_offset.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Since commit d70ed2e4fafdbef0800e739
MD: Allow restarting an interrupted incremental recovery.
we don't write out the metadata to devices while they are recovering.
This had a good reason, but has unfortunate consequences. This patch
changes things to make them work better.
At issue is what happens if the array is shut down while a recovery is
happening, particularly a bitmap-guided recovery.
Ideally the recovery should pick up where it left off.
However the metadata cannot represent the state "A recovery is in
process which is guided by the bitmap".
Before the above mentioned commit, we wrote metadata to the device
which said "this is being recovered and it is up to <here>". So after
a restart, a full recovery (not bitmap-guided) would happen from
where-ever it was up to.
After the commit the metadata wasn't updated so it still said "This
device is fully in sync with <this> event count". That leads to a
bitmap-based recovery following the whole bitmap, which should be a
lot less work than a full recovery from some starting point. So this
was an improvement.
However updates some metadata but not all leads to other problems.
In particular, the metadata written to the fully-up-to-date device
record that the array has all devices present (even though some are
recovering). So on restart, mdadm wants to find all devices and
expects them to have current event counts.
Obviously it doesn't (some have old event counts) so (when assembling
with --incremental) it waits indefinitely for the rest of the expected
devices.
It really is wrong to not update all the metadata together. Do that
is bound to cause confusion.
Instead, we should make it possible to record the truth in the
metadata. i.e. we need to be able to record that a device is being
recovered based on the bitmap.
We already have a Feature flag to say that recovery is happening. We
now add another one to say that it is a bitmap-based recovery.
With this we can remove the code that disables the write-out of
metadata on some devices.
So this patch:
- moves the setting of 'saved_raid_disk' from add_new_disk to
the validate_super methods. This makes sure it is always set
properly, both when adding a new device to an array, and when
assembling an array from a collection of devices.
- Adds a metadata flag MD_FEATURE_RECOVERY_BITMAP which is only
used if MD_FEATURE_RECOVERY_OFFSET is set, and record that a
bitmap-based recovery is allowed.
This is only present in v1.x metadata. v0.90 doesn't support
devices which are in the middle of recovery at all.
- Only skips writing metadata to Faulty devices.
- Also allows rdev state to be set to "-insync" via sysfs.
This can be used for external-metadata arrays. When the
'role' is set the device is assumed to be in-sync. If, after
setting the role, we set the state to "-insync", the role is
moved to saved_raid_disk which effectively says the device is
partly in-sync with that slot and needs a bitmap recovery.
Cc: Andrei Warkentin <andreiw@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If an array is started degraded, and then the missing device
is found it can be re-added and a minimal bitmap-based recovery
will bring it fully up-to-date.
If the array is read-only a recovery would not be allowed.
But also if the array is read-only and the missing device was
present very recently, then there could be no need for any
recovery at all, so we simply include the device in the read-only
array without any recovery.
However... if the missing device was removed a little longer ago
it could be missing some updates, but if a bitmap is present it will
be conditionally accepted pending a bitmap-based update. We don't
currently detect this case properly and will include that old
device into the read-only array with no recovery even though it really
needs a recovery.
This patch keeps track of whether a bitmap-based-recovery is really
needed or not in the new Bitmap_sync rdev flag. If that is set,
then the device will not be added to a read-only array.
Cc: Andrei Warkentin <andreiw@vmware.com>
Fixes: d70ed2e4fafdbef0800e73942482bb075c21578b
Cc: stable@vger.kernel.org (3.2+)
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit e875ecea266a543e643b19e44cf472f1412708f9
md/raid10 record bad blocks as needed during recovery.
added code to the "cannot recover this block" path to record a bad
block rather than fail the whole recovery.
Unfortunately this new case was placed *after* r10bio was freed rather
than *before*, yet it still uses r10bio.
This is will crash with a null dereference.
So move the freeing of r10bio down where it is safe.
Cc: stable@vger.kernel.org (v3.1+)
Fixes: e875ecea266a543e643b19e44cf472f1412708f9
Reported-by: Damian Nowak <spam@nowaker.net>
URL: https://bugzilla.kernel.org/show_bug.cgi?id=68181
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit 6d183de4077191d1201283a9035ce57a9b05254d
md/raid5: fix newly-broken locking in get_active_stripe.
simplified a BUG_ON, but removed too much so now it sometimes fires
when it shouldn't.
When the STRIPE_EXPANDING flag is set, the stripe_head might be on a
special list while multiple stripe_heads are collected, or it might
not be on any list, even a 'free' list when the refcount is zero. As
long as STRIPE_EXPANDING is set, it will be found and added back to a
list eventually.
So both of the BUG_ONs which test for the ->lru being empty or not
need to avoid the case where STRIPE_EXPANDING is set.
The patch which broke this was marked for -stable, so this patch needs
to be applied to any branch that received 6d183de4
Fixes: 6d183de4077191d1201283a9035ce57a9b05254d
Cc: stable@vger.kernel.org (any release to which above was applied)
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The new iobarrier implementation in raid1 (which keeps normal writes
and resync activity separate) counts every request what is not before
the current resync point in either next_window_requests or
current_window_requests.
It flags that the request is counted by setting ->start_next_window.
allow_barrier follows this model exactly and decrements one of the
*_window_requests if and only if ->start_next_window is set.
However wait_barrier(), which increments *_window_requests uses a
slightly different test for setting -.start_next_window (which is set
from the return value of this function).
So there is a possibility of the counts getting out of sync, and this
leads to the resync hanging.
So change wait_barrier() to return a non-zero value in exactly the
same cases that it increments *_window_requests.
But was introduced in 3.13-rc1.
Reported-by: Bruno Wolff III <bruno@wolff.to>
URL: https://bugzilla.kernel.org/show_bug.cgi?id=68061
Fixes: 79ef3a8aa1cb1523cc231c9a90a278333c21f761
Cc: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If we discover a bad block when reading we split the request and
potentially read some of it from a different device.
The code path of this has two bugs in RAID10.
1/ we get a spin_lock with _irq, but unlock without _irq!!
2/ The calculation of 'sectors_handled' is wrong, as can be clearly
seen by comparison with raid1.c
This leads to at least 2 warnings and a probable crash is a RAID10
ever had known bad blocks.
Cc: stable@vger.kernel.org (v3.1+)
Fixes: 856e08e23762dfb92ffc68fd0a8d228f9e152160
Reported-by: Damian Nowak <spam@nowaker.net>
URL: https://bugzilla.kernel.org/show_bug.cgi?id=68181
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit 5d8c71f9e5fbdd95650be00294d238e27a363b5c
md: raid5 crash during degradation
Fixed a crash in an overly simplistic way which could leave
R5_WriteError or R5_MadeGood set in the stripe cache for devices
for which it is no longer relevant.
When those devices are removed and spares added the flags are still
set and can cause incorrect behaviour.
commit 14a75d3e07c784c004b4b44b34af996b8e4ac453
md/raid5: preferentially read from replacement device if possible.
Fixed the same bug if a more effective way, so we can now revert
the original commit.
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Cc: stable@vger.kernel.org (3.2+ - 3.2 will need a different fix though)
Fixes: 5d8c71f9e5fbdd95650be00294d238e27a363b5c
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Trivial: remove the few stray references to css_id, which itself
was removed in v3.13's 2ff2a7d03bbe "cgroup: kill css_id".
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Improve cache_status to emit:
<metadata block size> <#used metadata blocks>/<#total metadata blocks>
<cache block size> <#used cache blocks>/<#total cache blocks>
...
Adding the block sizes allows for easier calculation of the overall size
of both the metadata and cache devices. Adding <#total cache blocks>
provides useful context for how much of the cache is used.
Unfortunately these additions to the status will require updates to
users' scripts that monitor the cache status. But these changes help
provide more comprehensive information about the cache device and will
simplify tools that are being developed to manage dm-cache devices --
because they won't need to issue 3 operations to cobble together the
information that we can easily provide via a single status ioctl.
While updating the status documentation in cache.txt spaces were
tabify'd.
Requested-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
|
|
dm_btree_find_lowest_key is the reciprocal of dm_btree_find_highest_key.
Factor out common code for dm_btree_find_{highest,lowest}_key.
dm_btree_find_lowest_key is needed for an upcoming DM target, as such it
is best to get this interface in place.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
|
|
We need to return -EINTR after a split because we invalidated iterators
(and freed the btree node) - but if we were finished inserting, we don't
want to redo the traversal.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
|
|
When deciding what order to reuse buckets we take into account both the bucket's
priority (which indicates lru order) and also the amount of live data in that
bucket. The way they were scaled together wasn't as correct as it could be...
this patch improves and documents it.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
|
|
Checks if two keys have equivalent header fields.
(good enough for replacement or merging)
Used in bch_bkey_try_merge, and replacing a key
in the btree.
Signed-off-by: Nicholas Swenson <nks@daterainc.com>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
|
|
Added generic header checks to bch_bkey_try_merge,
which then calls the bkey specific function
Removed extraneous checks from bch_extent_merge
Signed-off-by: Nicholas Swenson <nks@daterainc.com>
|
|
Now handling overlapping extents/keys is a method that's specific to what the
btree node contains.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
|
|
More work to disentangle various code from struct btree
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
|
|
More work to disentangle various code from struct btree
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
|
|
More work to disentangle bset.c from struct btree
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
|
|
We're in the process of turning bset.c into library code, so none of the code in
that file should know about struct cache_set or struct btree - so, move the
btree traversal part of the stats code to sysfs.c.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
|
|
Helper function to explicitly check how much space is free in a btree node
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
|
