| Age | Commit message (Collapse) | Author |
|---|
|
We currently unregister the config-osm driver if initialization of the
legacy ioctl() handlers failed but still return success. We should be
returning -EBUSY in this case.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
On Thursday, September 15, 2005 6:22 AM, Christoph Hellwig wrote:
> Looks good to me, except for the spurious scsi_print_command prototype
> in mptscsih.h.
The attached patch addresses that concern.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Summary of Changes:
* splitting mpt_interrupt per Christophs suggestion
about a month ago
* rename ScsiCfgData to SpiCfgData structure,
then move all the raid related info into
new structure called RaidCfgData. This is
done because SAS supports RAID, as well as SPI,
so the raid stuff should be seperate.
* incorrect timeout calculation for cntdn
inside WaitForDoorbellAck and WaitForDoortbellInt
* add support for interpreting SAS Log Info
* Increase Event Log Size from 0xA to 0x32
* Fix bug in mptsas/mptfc/mptspi - when controller
has Initiator Mode Disabled, and only running in
TargetMode, the mptctl would panic when loading.
The fix is to return 0, instead of -ENODEV, in
SCSI LLD respective probe routines
* Fix bug in mptlan.c - driver will panic if
there is host reset, due to dev being set to
zero in mpt_lan_ioc_reset
* Fix's for SPI - Echo Buffer
* Several fix's in mptscsih_io_done - FCP Response
info, RESIDUAL_MISMATCH, Data Underrun, etc.
* Cleanup Error Handling - EH handlers,
mptscsih_flush_cmds, and zeroing out ScsiLookup
from mptscsih_qcmd
* Cleanup asyn event handling from
mptscsih -> mptscsih_event_process. Also
added support for SAS Persistent Table Full,
an asyn event
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Adds the actual mptsas driver, based upon the LSI driver with new work
for SAS transport class integration from Eric Moore and me.
This obviously depends on the SAS transport class.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
- various bits for SAS support from the LSI driver.
- use the device private data for the fusion target private data.
this should be using the midlayer target data framework, but we
can't move over to that until fusion has been switched to the
generic DV code
- use target ID and channel from the fusion target private data,
because those in scsi_device will be different for mptsas
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
|
|
Acked by: Moore, Eric Dean <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Assorted endianess fixes. I'll work on full endianess annotations
later.
Acked by: Moore, Eric Dean <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Acked by: Moore, Eric Dean <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Acked by: Moore, Eric Dean <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Added pci_request_regions() before using the controller to avoid duplicate
usage of the I2O controller when the dpt_i2o driver and I2O subsystem is
loaded at the same time.
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove new configuration API from i2o_config
The API-patch is still available from the I2O website (which is mentioned in
the kernel config now). It is removed because it creates a new binary
sysfs-attribute, which doesn't have the limitiation of 4k. Expect for the
Adaptec controllers, which has a limitation in the hardware this attribute
doesn't make sense anywhere else. Until the sysfs API provides an attribute
which doesn't buffer (like firmware) and let access to at least 64k blocks i
provide a separate patch...
(akpm: basically, this API was introduced post-2.6.12 and Markus wants to pull
it out before 2.6.13).
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
Few more u32 vs. pm_message_t fixes.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Various stuff missing on alpha:
drivers/message/i2o/config-osm.c:35: error: field `fops' has incomplete type
drivers/message/i2o/config-osm.c: In function `sysfs_create_fops_file':
drivers/message/i2o/config-osm.c:71: error: storage size of `tmp' isn't known
drivers/message/i2o/config-osm.c:78: error: dereferencing pointer to incomplete type
drivers/message/i2o/config-osm.c:81: error: dereferencing pointer to incomplete type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Convert driver to use new change_queue_depth API.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Fixed up rejections and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
driver core callback.
Now we can change the pci core to always set this pointer, as pci drivers
should use it, not the driver core callback.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
scsi_add_host is the proper place to set the device, but people copy
the scsi_set_device usage from older drivers again and again.
note that this leaves some legacy drivers like qlogicisp/qlogicfc
without pci association in sysfs, but they're scheduled to go away soon
anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This patch updates all the device attribute callbacks that weren't
updated with the new parameter, I guess because they weren't in Greg's
tree (including drivers/pcmcia/ds.c). Without the patch these
callbacks are probably broken (and generate a warning along the lines
of "assignment from incompatible pointer type").
Please see http://lkml.org/lkml/2005/5/19/40 for the scripts I used to
update the attributes automatically.
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
LD .tmp_vmlinux1
drivers/built-in.o: In function `i2o_cfg_parms':
config-osm.c:(.text+0x12764a): undefined reference to `i2o_parm_issue'
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Set max sectors to 256 for Promise controllers.
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
functions
Lindent run and replaced printk() through the corresponding osm_*() function
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Changes:
- Added header "core.h" for i2o_core.ko internal definitions
- More sparse fixes
- Changed display of TID's in sysfs attributes from XXX to 0xXXX
- Use the right functions for accessing I/O and normal memory
- Removed error handling of SCSI device errors and let the SCSI layer
take care of it
- Added new device / removed device handling to SCSI-OSM
- Make status access volatile
- Cleaned up activation of I2O controller
- Removed unnecessary wmb() and rmb() calls
- Use own struct i2o_io for I/O memory instead of struct i2o_dma
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
and 2400A workaround
Changes:
- Provide SG_IO access to BLOCK and EXECUTIVE class on Adaptec
controllers
- Use PRIVATE messages in SCSI-OSM because on some controllers normal
SCSI class commands like READ or READ CAPACITY cause errors
- Use new DMA and SG list creation function
- Added workaround to limit sectors per request for Adaptec 2400A
controllers
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
and 64-bit DMA support
Changes:
- Added Bus-OSM which could be used by user space programs to reset a
channel on the controller
- Make ioctl's in Config-OSM obsolete in prefer for sysfs attributes and
move those to its own file
- Added sysfs attribute for firmware read and write access for I2O
controllers
- Added special handling of firmware read and write access for Adaptec
controllers
- Added vendor id and product id as sysfs-attribute to Executive classes
- Added automatic notification of LCT change handling to Exec-OSM
- Added flushing function to Block-OSM for later barrier implementation
- Use PRIVATE messages for Block access on Adaptec controllers, which are
faster then BLOCK class access
- Cleaned up support for Promise controller
- New messages are now detected using the IRQ status register as
suggested by the I2O spec
- Added i2o_dma_high() and i2o_dma_low() functions
- Added facility for SG tablesize calculation when using 32-bit and
64-bit DMA addresses
- Added i2o_dma_map_single() and i2o_dma_map_sg() which could build the
SG list for 32-bit as well as 64-bit DMA addresses
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Changes:
- Removed unnecessary checking of NULL before calling kfree()
- Make some functions static
- Changed pr_debug() into osm_debug()
- Use i2o_msg_in_to_virt() for getting a pointer to the message frame
- Cleaned up some comments
- Changed some le32_to_cpu() into readl() where necessary
- Make error messages of OSM's look the same
- Cleaned up error handling in i2o_block_end_request()
- Removed unused error handling of failed messages in Block-OSM, which
are not allowed by the I2O spec
- Corrected the blocksize detection in i2o_block
- Added hrt and lct sysfs-attribute to controller
- Call done() function in SCSI-OSM after freeing DMA buffers
- Removed unneeded variable for message size calculation in
i2o_scsi_queuecommand()
- Make some changes to remove sparse warnings
- Reordered some functions
- Cleaned up controller initialization
- Replaced some magic numbers by defines
- Removed unnecessary dma_sync_single_for_cpu() call on coherent DMA
- Removed some unused fields in i2o_controller and removed some unused
functions
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Changes:
- Fixed sysfs bug where user and parent links where added to the I2O
device itself
- Fixed bug when calculating TID for the event handler and cleaned up the
workflow of i2o_driver_dispatch()
- Fixed oops when no I2O device could be found for an event delivered to
Exec-OSM
- Fixed initialization of spinlock in Exec-OSM
- Fixed memory leak in i2o_cfg_passthru() and i2o_cfg_passthru()
- Removed MTRR support
- Added PCI ID of Promise SX6000 with firmware >= 1.20.x.x
- Turn of caching for ioremapped memory of in_queue
- Added initialization sequence for Promise controllers
- Moved definition of u8 / u16 / u32 for raidutils before first use
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
drivers/s390/block/dcssblk.c: update device attribute callbacks
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
|
|
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Fixed freeing of event memory in i2o_block_event()
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Bump driver version to 3.03.02
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This patch contains update for mpi headers 1.5.9.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
* This patch clarifies help section in FUSION_MAX_SGE entry.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This patch is originally From: Jesper Juhl <juhl-lkml@dif.dk>
This patch gets rid of redundant NULL checks prior to calling kfree() in
drivers/message/* There are also a few small whitespace changes in there.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
* adding pci id support for new Fibre chips, 949X and 939X
* adding errata workaround - disabling PIO access except during fwdlb.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Adjust link ordering in the Makefile. Also, the ioc->DoneCtx handles
for mptspi/mptfc in the message frame. And I'm now not seeing the
panic.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The fusion Kconfig forgets to set CONFIG_FUSION, which is required to
get the upper makefile to descend into the fusion directory. Add this
back as a variable and make the two upper level modules select it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
(1) mptfc.c: This driver is having module_init, module_exit, and probe.
(2) mptfc.c: Registering for Fibre Channel pci ids are done from this
module.
(3) mptfc.c: Convert MODULE_PARM to module_param
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
(1) mptspi.c: This driver is having module_init, module_exit, and probe.
(2) mptspi.c: Registering for SCSI pci ids are done from this module.
(3) mptspi.c: Convert MODULE_PARM to module_param
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
(1) mptscsih.c: Remove credits, -sralston references , update copyright
(2) mptscsih.c: split driver support
(3) mptscsih.c: module_init, module_exit, and probe routines moved to new
stub drivers, mptfc and mptspi
(4) mptscsih.c: some global parameters are moved to MPT_SCSI_HOST
(5) mptscsih.c: removed scsi_device_online check.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
(1) mptlan.c: Remove credits and update copyright
(2) mptlan.c: Remove -sralston references
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
(1) mptctl.c: Remove credits and update copyright
(2) mptctl.c: cleanup in get_iocinfo
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
(1) mptbase.c: Move registering pci ids to scsi lld drivers
(2) mptbase.c: Use the DMA_32BIT_MASK constant
(3) mptbase.c: Fix for multiple pci domains
(4) mptbase.c: Remove le32 conversion from BlockSize, which was u8 size
(5) mptbase.c: Remove credits, -sralston references , update copyright
(6) mptbase.c: split driver support
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
(1) Kconfig - added new mptspi and mptfc scsi lld drivers
(2) Kconfig - increased MAX_SGE from 40 to 128
(2) Makefile - compilation support for split drivers
(3) Makefile - cleaned up debug defines; e.g. removed obsolete, added others
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Also broken design in its compat handlers - CONFIG_COMPAT doesn't
mean that there should be no native ioctls.
Signed-off-by: Andi Kleen <ak@muc.de>
Reworked with comments from Markus Lidel by:
Christoph Hellwig <hch@infradead.org>
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
This fixes u32 vs. pm_message_t in drivers/message.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
