| Age | Commit message (Collapse) | Author |
|---|
|
regulators
Commit 43fef47f94a1 (mfd: twl4030-power: Add a configuration to turn
off oscillator during off-idle) added support for configuring the PMIC
to cut off resources during deeper idle states to save power.
This however caused regression for n900 display power that needed the
PMIC configuration to be disabled with commit d937678ab625 (ARM: dts:
Revert enabling of twl configuration for n900).
Turns out the root cause of the problem is that we must use
TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling
regulators that may have been enabled before the init function
for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the
regulator framework control the regulators like it should. Here we
need to only configure the sys_clken and sys_off_mode triggers for
the regulators that cannot be done by the regulator framework as
it's not running at that point.
This allows us to enable the PMIC configuration for n900.
Fixes: 43fef47f94a1 (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle)
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The config symbol 'CONFIG_DEBUG_FS' should be protected by a 'ifdef' instead
of a plain 'if'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The rtsx_usb driver contains the table for the devices it supports but
doesn't export it. As a result, no alias is generated and it doesn't
get loaded automatically.
Via https://bugzilla.novell.com/show_bug.cgi?id=890096
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: Marcel Witte <wittemar@googlemail.com>
Cc: Roger Tseng <rogerable@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
|
|
'regulator/topic/s2mpu02', 'regulator/topic/s5m8767' and 'regulator/topic/tps65090' into regulator-next
|
|
'regulator/topic/ltc3589', 'regulator/topic/max8952', 'regulator/topic/mc13xxx' and 'regulator/topic/palmas' into regulator-next
|
|
single-ulpi-bypass is a flag used for older OMAP3 silicon.
The flag when set, can excite code that improperly uses the
OMAP_UHH_HOSTCONFIG_UPLI_BYPASS define to clear the corresponding bit.
Instead it clears all of the other bits disabling all of the ports in
the process.
Cc: stable@vger.kernel.org
Signed-off-by: Michael Welling <mwelling@emacinc.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We only request the control interface error IRQ if we set ctrlif_error,
as such we should only free it in that situation. Otherwise we will
attempt to free an IRQ we never requested and get a warning from the IRQ
core.
This patch moves the ctrlif_error variable into the arizona structure
and checks it in all cases we free the control interface error IRQ.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Some parts have a third ISRC, this patch adds handling for the under and
overclocked interrupts from this ISRC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Newer versions of the IP have a lot of new interrupts and move several
existing interrupts. This patch adds the register definitions and regmap
hookup for these interrupts.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Newer versions of the IP introduce short circuit protection which will
also shutdown the speaker. Rename the interrupt and associated register
bits associated with thermal events to better fit the function and avoid
conflict with future interrupt additions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
wm5110 has interrupts to signal that an output has fully enabled. This
patch adds in these interrupts although use is not made of them yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The DCS_DAC_DONE and DCS_HP_DONE interrupts do not exist on the wm5110
version of the IP. This patch removes them from the regmap IRQ
structure.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
‘rx_buf’ is not used in this function.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Removed code unused in this function.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add register definitions for DA9063 AD (0x3) silicon variant ID
the ability to choose the silicon variant at run-time using regmap
configuration. This patch also adds RTC support for the AD silicon
changes.
It adds both BB and AD support as regmap ranges and then makes the
distinction between the two tables at run-time. This allows both AD
and BB silicon variants to be supported at the same time.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The extcon driver should be able to get its regulator against rather
than against the main arizona device, we must add a supply mapping
allowing the regulator to be located. This patch does so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The previous update adding MICVDD to the regulator mappings:
mfd: arizona: Add MICVDD to mapped regulators
Only added the mapping for wm5102 and wm5110 but wm8997 also has a
MICVDD supply that needs to be mapped back to the main Arizona device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Extinguishes:
../drivers/mfd/max77686.c: In function ‘max77686_i2c_probe’:
../drivers/mfd/max77686.c:254:20:
warning: cast from pointer to integer of different size
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Maxim MAX77802 is a power management chip that contains 10 high
efficiency Buck regulators, 32 Low-dropout (LDO) regulators used
to power up application processors and peripherals, a 2-channel
32kHz clock outputs, a Real-Time-Clock (RTC) and a I2C interface
to program the individual regulators, clocks outputs and the RTC.
This patch adds support for MAX77802 to the MAX77686 driver and is
based on a driver added to the Chrome OS kernel 3.8 by Simon Glass.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch introduces the use of devm_kzalloc instead of the
corresponding unmanaged version and does away with the kfrees in the
probe and remove functions. Also, a label is done away with.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: line over 80 characters
+ { 0x00000068, 0x01FF }, /* R104 - Always On Triggers Sequence Select 3 */
WARNING: line over 80 characters
+ { 0x00000069, 0x01FF }, /* R105 - Always On Triggers Sequence Select 4 */
WARNING: line over 80 characters
+ { 0x0000006A, 0x01FF }, /* R106 - Always On Triggers Sequence Select 5 */
WARNING: line over 80 characters
+ { 0x0000006B, 0x01FF }, /* R107 - Always On Triggers Sequence Select 6 */
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
WARNING: line over 80 characters
+module_param_string(force_device_id, force_device_id, sizeof(force_device_id), 0);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: __initdata should be placed after kempld_dmi_table[]
+static struct dmi_system_id __initdata kempld_dmi_table[] = {
WARNING: line over 80 characters
+ for (id = kempld_dmi_table; id->matches[0].slot != DMI_NONE; id++)
total: 0 errors, 4 warnings, 771 lines checked
This is part of an effort to clean-up the MFD subsystem.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
ERROR: space required before the open parenthesis '('
+ if(!micro->msg)
WARNING: unnecessary whitespace before a quoted newline
+ dev_dbg(micro->dev, "key message ignored, no handle \n");
WARNING: unnecessary whitespace before a quoted newline
+ dev_dbg(micro->dev, "touchscreen message ignored, no handle \n");
WARNING: space prohibited before semicolon
+ rx->id = (ch & 0xf0) >> 4 ;
total: 1 errors, 3 warnings, 482 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: line over 80 characters
+ struct si476x_rsq_status_args *rsqargs,
WARNING: line over 80 characters
+ struct si476x_rsq_status_report *report)
WARNING: Unnecessary space before function pointer arguments
+ int (*power_up) (struct si476x_core *,
WARNING: Unnecessary space before function pointer arguments
+ int (*power_down) (struct si476x_core *,
total: 0 errors, 4 warnings, 1555 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: braces {} are not necessary for single statement blocks
+ if (!iomem) {
+ return -EINVAL;
+ }
WARNING: sizeof *tc6387xb should be sizeof(*tc6387xb)
+ tc6387xb = kzalloc(sizeof *tc6387xb, GFP_KERNEL);
WARNING: Prefer [subsystem eg: netdev]_info([subsystem]dev, ... then dev_info(dev, ... then pr_info(... to printk(KERN_INFO ...
+ printk(KERN_INFO "Toshiba tc6387xb initialised\n");
total: 0 errors, 3 warnings, 242 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: please, no space before tabs
+^IRSV_INTR_OFFSET, ^I/* Bit 12^IReserved^I^I*/$
WARNING: Missing a blank line after declarations
+ u8 unmask_value;
+ ret = twl_i2c_read_u8(TWL_MODULE_PIH, &unmask_value,
WARNING: Missing a blank line after declarations
+ u8 mask_value;
+ ret = twl_i2c_read_u8(TWL_MODULE_PIH, &mask_value,
total: 0 errors, 3 warnings, 484 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: please, no spaces at the start of a line
+ { "wm8350", 0 },$
WARNING: please, no spaces at the start of a line
+ { "wm8351", 0 },$
WARNING: please, no spaces at the start of a line
+ { "wm8352", 0 },$
WARNING: please, no spaces at the start of a line
+ { }$
total: 0 errors, 4 warnings, 93 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: Missing a blank line after declarations
+ struct max8925_chip *chip = irq_data_get_irq_chip_data(data);
+ max8925_irqs[data->irq - chip->irq_base].enable
WARNING: Missing a blank line after declarations
+ struct max8925_chip *chip = irq_data_get_irq_chip_data(data);
+ max8925_irqs[data->irq - chip->irq_base].enable = 0;
total: 0 errors, 2 warnings, 927 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: Prefer pr_warn(... to pr_warning(...
+ pr_warning("twl4030: I2C error %d reading PIH ISR\n", ret);
WARNING: sizeof buf should be sizeof(buf)
+ memset(buf, 0xff, sizeof buf);
WARNING: sizeof *agent should be sizeof(*agent)
+ agent = kzalloc(sizeof *agent, GFP_KERNEL);
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: Missing a blank line after declarations
+ struct lp8788_irq_data *irqd = irq_data_get_irq_chip_data(data);
+ irqd->enabled[data->hwirq] = 1;
WARNING: Missing a blank line after declarations
+ struct lp8788_irq_data *irqd = irq_data_get_irq_chip_data(data);
+ irqd->enabled[data->hwirq] = 0;
total: 0 errors, 2 warnings, 198 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: sizeof t should be sizeof(t)
+ memset(&t, 0, sizeof t);
WARNING: void function return statements are not generally useful
+ return;
+}
total: 0 errors, 2 warnings, 542 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Replace the ever recurring:
ts = ktime_get_ts();
ns = timespec_to_ns(&ts);
with
ns = ktime_get_ns();
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
ERROR: space required after that ',' (ctx:VxO)
+ 0, &twl6040_irq_chip,&twl6040->irq_data);
^
ERROR: space required before that '&' (ctx:OxV)
+ 0, &twl6040_irq_chip,&twl6040->irq_data);
^
total: 2 errors, 0 warnings, 816 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: Missing a blank line after declarations
+ const struct of_device_id *match;
+ match = of_match_node(sec_dt_match, i2c->dev.of_node);
total: 0 errors, 1 warnings, 494 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
ERROR: space required after that ',' (ctx:VxV)
+#define MSP_GPIO(bit,reg) ((DM355EVM_MSP_ ## reg) << 3 | (bit))
^
total: 1 errors, 0 warnings, 437 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: line over 80 characters
+ wm8350->irq_base = irq_alloc_descs(irq_base, 0, ARRAY_SIZE(wm8350_irqs), 0);
total: 0 errors, 1 warnings, 552 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: Missing a blank line after declarations
+ unsigned long flags;
+ spin_lock_irqsave(&mcp->lock, flags);
total: 0 errors, 1 warnings, 238 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
WARNING: Missing a blank line after declarations
+ int ret;
+ ret = i2c_add_driver(&max8925_driver);
total: 0 errors, 1 warnings, 275 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is part of an effort to clean-up the MFD subsystem.
+WARNING: line over 80 characters
+ &max77686_rtc_regmap_config);
total: 0 errors, 1 warnings, 299 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
There is no need to print out-of-memory errors since this is already
done by the memory management subsystem which even calls dump_stack().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Error checking across the driver is mostly consistent besides
a few exceptions, so change these exceptions for consistency.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
When platform data is not found an -EIO (I/O error) code is returned.
This doesn't seem to be the correct error so better return -EINVAL
(Invalid argument) which is what most drivers do in this case.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The function max77802_i2c_parse_dt_pdata() should only be called
if there isn't already platform data for the device.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
When the CONFIG_OF option was not enabled, a dummy function
max77686_i2c_parse_dt_pdata() was defined since this is called
unconditionally on probe(). Just always define the real function
and conditionally call it if CONFIG_OF is enabled instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The driver doesn't have PM operations defined so add a suspend
and resume function handlers to allow the PMIC IRQ to wakeup
the system when it is put into a sleep state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
