summaryrefslogtreecommitdiffstats
path: root/drivers/mfd
AgeCommit message (Collapse)Author
2014-11-10mfd: twl4030-power: Fix poweroff with PM configuration enabledTony Lindgren
Commit e7cd1d1eb16f ("mfd: twl4030-power: Add generic reset configuration") enabled configuring the PM features for twl4030. This caused poweroff command to fail on devices that have the BCI charger on twl4030 wired, or have power wired for VBUS. Instead of powering off, the device reboots. This is because voltage is detected on charger or VBUS with the default bits enabled for the power transition registers. To fix the issue, let's just clear VBUS and CHG bits as we want poweroff command to keep the system powered off. Fixes: e7cd1d1eb16f ("mfd: twl4030-power: Add generic reset configuration") Cc: stable@vger.kernel.org # v3.16+ Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10mfd: max77693: Fix always masked MUIC interruptsKrzysztof Kozlowski
All interrupts coming from MUIC were ignored because interrupt source register was masked. The Maxim 77693 has a "interrupt source" - a separate register and interrupts which give information about PMIC block triggering the individual interrupt (charger, topsys, MUIC, flash LED). By default bootloader could initialize this register to "mask all" value. In such case (observed on Trats2 board) MUIC interrupts won't be generated regardless of their mask status. Regmap irq chip was unmasking individual MUIC interrupts but the source was masked Before introducing regmap irq chip this interrupt source was unmasked, read and acked. Reading and acking is not necessary but unmasking is. Fixes: 342d669c1ee4 ("mfd: max77693: Handle IRQs using regmap") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10mfd: max77693: Use proper regmap for handling MUIC interruptsKrzysztof Kozlowski
Interrupts coming from Maxim77693 MUIC block (MicroUSB Interface Controller) were not handled at all because wrong regmap was used for MUIC's regmap_irq_chip. The MUIC component of Maxim 77693 uses different I2C address thus second regmap is created and used by max77693 extcon driver. The registers for MUIC interrupts are also in that block and should be handled by that second regmap. However the regmap irq chip for MUIC was configured with default regmap which could not read MUIC registers. Fixes: 342d669c1ee4 ("mfd: max77693: Handle IRQs using regmap") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10mfd: viperboard: Fix platform-device id collisionJohan Hovold
Allow more than one viperboard to be connected by registering with PLATFORM_DEVID_AUTO instead of PLATFORM_DEVID_NONE. The subdevices are currently registered with PLATFORM_DEVID_NONE, which will cause a name collision on the platform bus when a second viperboard is plugged in: viperboard 1-2.4:1.0: version 0.00 found at bus 001 address 004 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 181 at /home/johan/work/omicron/src/linux/fs/sysfs/dir.c:31 sysfs_warn_dup+0x74/0x84() sysfs: cannot create duplicate filename '/bus/platform/devices/viperboard-gpio' Modules linked in: i2c_viperboard viperboard netconsole [last unloaded: viperboard] CPU: 0 PID: 181 Comm: bash Tainted: G W 3.17.0-rc6 #1 [<c0016bf4>] (unwind_backtrace) from [<c0013860>] (show_stack+0x20/0x24) [<c0013860>] (show_stack) from [<c04305f8>] (dump_stack+0x24/0x28) [<c04305f8>] (dump_stack) from [<c0040fb4>] (warn_slowpath_common+0x80/0x98) [<c0040fb4>] (warn_slowpath_common) from [<c004100c>] (warn_slowpath_fmt+0x40/0x48) [<c004100c>] (warn_slowpath_fmt) from [<c016f1bc>] (sysfs_warn_dup+0x74/0x84) [<c016f1bc>] (sysfs_warn_dup) from [<c016f548>] (sysfs_do_create_link_sd.isra.2+0xcc/0xd0) [<c016f548>] (sysfs_do_create_link_sd.isra.2) from [<c016f588>] (sysfs_create_link+0x3c/0x48) [<c016f588>] (sysfs_create_link) from [<c02867ec>] (bus_add_device+0x12c/0x1e0) [<c02867ec>] (bus_add_device) from [<c0284820>] (device_add+0x410/0x584) [<c0284820>] (device_add) from [<c0289440>] (platform_device_add+0xd8/0x26c) [<c0289440>] (platform_device_add) from [<c02a5ae4>] (mfd_add_device+0x240/0x344) [<c02a5ae4>] (mfd_add_device) from [<c02a5ce0>] (mfd_add_devices+0xb8/0x110) [<c02a5ce0>] (mfd_add_devices) from [<bf00d1c8>] (vprbrd_probe+0x160/0x1b0 [viperboard]) [<bf00d1c8>] (vprbrd_probe [viperboard]) from [<c030c000>] (usb_probe_interface+0x1bc/0x2a8) [<c030c000>] (usb_probe_interface) from [<c028768c>] (driver_probe_device+0x14c/0x3ac) [<c028768c>] (driver_probe_device) from [<c02879e4>] (__driver_attach+0xa4/0xa8) [<c02879e4>] (__driver_attach) from [<c0285698>] (bus_for_each_dev+0x70/0xa4) [<c0285698>] (bus_for_each_dev) from [<c0287030>] (driver_attach+0x2c/0x30) [<c0287030>] (driver_attach) from [<c030a288>] (usb_store_new_id+0x170/0x1ac) [<c030a288>] (usb_store_new_id) from [<c030a2f8>] (new_id_store+0x34/0x3c) [<c030a2f8>] (new_id_store) from [<c02853ec>] (drv_attr_store+0x30/0x3c) [<c02853ec>] (drv_attr_store) from [<c016eaa8>] (sysfs_kf_write+0x5c/0x60) [<c016eaa8>] (sysfs_kf_write) from [<c016dc68>] (kernfs_fop_write+0xd4/0x194) [<c016dc68>] (kernfs_fop_write) from [<c010fe40>] (vfs_write+0xb4/0x1c0) [<c010fe40>] (vfs_write) from [<c01104a8>] (SyS_write+0x4c/0xa0) [<c01104a8>] (SyS_write) from [<c000f900>] (ret_fast_syscall+0x0/0x48) ---[ end trace 98e8603c22d65817 ]--- viperboard 1-2.4:1.0: Failed to add mfd devices to core. viperboard: probe of 1-2.4:1.0 failed with error -17 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10mfd: rtsx: Fix build warnings for !PMThierry Reding
rtsx_pci_power_off() is called only from rtsx_pci_suspend(), which isn't built when PM is disabled. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-11-10mfd: stmpe: Fix STMPE24xx GPMR LSBLinus Walleij
The least significat byte of the GPIO value read register on the STMPE24xx series is on addres 0xA4 not 0xA5. Correct against datasheet and tested on the STMPE2401 hardware. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-10-15Merge tag 'mfd-for-linus-3.18' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd Pull MFD updates from Lee Jones: "Changes to existing drivers: - DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030 - Export symbols for use in modules in max14577 - Plenty of static code analysis/Coccinelle fixes throughout the SS - Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808 - Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona - Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr - IRQ fixups in arizona, stmpe, max14577 - Regulator related changes in axp20x - Pass DMA coherency information from parent => child in MFD core - Rename DT document files for consistency - Add ACPI support to the MFD core - Add Andreas Werner to MAINTAINERS for MEN F21BMC New drivers/supported devices: - New driver for MEN 14F021P00 Board Management Controller - New driver for Ricoh RN5T618 PMIC - New driver for Rockchip RK808 - New driver for HiSilicon Hi6421 PMIC - New driver for Qualcomm SPMI PMICs - Add support for Intel Braswell in lpc_ich - Add support for Intel 9 Series PCH in lpc_ich - Add support for Intel Quark ILB in lpc_sch" [ Delayed to after the poweer/reset pull due to Kconfig problems with recursive Kconfig select/depends-on chains. - Linus ] * tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits) mfd: cros_ec: wait for completion of commands that return IN_PROGRESS i2c: i2c-cros-ec-tunnel: Set retries to 3 mfd: cros_ec: move locking into cros_ec_cmd_xfer mfd: cros_ec: stop calling ->cmd_xfer() directly mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC MAINTAINERS: Adds Andreas Werner to maintainers list for MEN F21BMC mfd: arizona: Correct mask to allow setting micbias external cap mfd: Add ACPI support Revert "mfd: wm5102: Manually apply register patch" mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS mfd: dt-bindings: atmel-gpbr: Rename doc file to conform to naming convention mfd: dt-bindings: qcom-pm8xxx: Rename doc file to conform to naming convention mfd: Inherit coherent_dma_mask from parent device mfd: Document DT bindings for Qualcomm SPMI PMICs mfd: Add support for Qualcomm SPMI PMICs mfd: dt-bindings: pm8xxx: Add new compatible string mfd: axp209x: Drop the parent supplies field mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off mfd: dt-bindings: twl4030-power: Use the standard property to mark power control mfd: syscon: Add Atmel GPBR DT bindings documention ...
2014-10-15Merge tag 'for-v3.18' of git://git.infradead.org/battery-2.6Linus Torvalds
Pull power supply and reset updates from Sebastian Reichel: - Initial support for the following chips * max77836 (charger) * max14577 (charger) * bq27742 (battery gauge) * ltc2952 (poweroff) * stih416 (restart) * syscon-reboot (restart) * gpio-restart (restart) - cleanup of power supply core - misc fixes in power supply and reset drivers * tag 'for-v3.18' of git://git.infradead.org/battery-2.6: (48 commits) power: ab8500_fg: Fix build warning Documentation: charger: max14577: Update the date of introducing ABI power: reset: corrections for simple syscon reboot driver Documentation: power: reset: Add documentation for generic SYSCON reboot driver power: reset: Add generic SYSCON register mapped reset bq27x00_battery: Fix flag reading for bq27742 power: reset: use restart_notifier mechanism for msm-poweroff power: Add simple gpio-restart driver power: reset: st: Provide DT bindings for ST's Power Reset driver power: reset: Add restart functionality for STiH41x platforms power: charger-manager: Fix NULL pointer exception with missing cm-fuel-gauge power: max14577: Fix circular config SYSFS dependency power: gpio-charger: do not use gpio value directly power: max8925: Use of_get_child_by_name power: max8925: Fix NULL ptr dereference on memory allocation failure bq27x00_battery: Add support to bq27742 Documentation: charger: max14577: Document exported sysfs entry devicetree: mfd: max14577: Add device tree bindings document power: max17040: Add ID for MAX77836 Fuel Gauge block charger: max14577: Configure battery-dependent settings from DTS and sysfs ... Conflicts: drivers/power/reset/Kconfig drivers/power/reset/Makefile
2014-10-10Merge tag 'hwmon-for-linus-v3.18' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull hwmon updates from Guenter Roeck: - new driver for menf21bmc. - convert k10temp, smsc47b397, da9052, da9055 to new hwmon API. - register ntc_thermistor driver with thermal subsystem. - add support for F15h M60h to k10temp driver. - add driver for MEN14F021P00 BMC HWMON driver; this required a merge with tag mfd-hwmon-leds-watchdog-v3.18 * tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: (ab8500) Call kernel_power_off instead of pm_power_off hwmon: (menf21bmc) Introduce MEN14F021P00 BMC HWMON driver leds: leds-menf21bmc: Introduce MEN 14F021P00 BMC LED driver watchdog: menf21bmc_wdt: Introduce MEN 14F021P00 BMC Watchdog driver mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver hwmon: (ntc_thermistor) Add ntc thermistor to thermal subsystem as a sensor. hwmon: (smsc47b397) Convert to devm_hwmon_device_register_with_groups MAINTAINERS: add entry for the PWM fan driver hwmon: (k10temp) Convert to devm_hwmon_device_register_with_groups hwmon: (k10temp) Add support for F15h M60h hwmon: (da9052) Convert to devm_hwmon_device_register_with_groups hwmon: (da9055) Convert to devm_hwmon_device_register_with_groups hwmon: (ads1015) Use of_property_read_u32 at appropriate places
2014-10-09Merge tag 'gpio-v3.18-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO changes from Linus Walleij: "This is the bulk of GPIO changes for the v3.18 development cycle: - Increase the default ARCH_NR_GPIO from 256 to 512. This was done to avoid having a custom <asm/gpio.h> header for the x86 architecture - GPIO is custom and complicated enough as it is already! We want to move to a radix to store the descriptors going forward, and finally get rid of this fixed array size altogether. - Endgame patching of the gpio_remove() semantics initiated by Abdoulaye Berthe. It is not accepted by the system that the removal of a GPIO chip fails during eg reboot or shutdown, and therefore the return value has now painfully been refactored away. For special cases like GPIO expanders on a hot-pluggable bus like USB, we may later add some gpiochip_try_remove() call, but for the cases we have now, return values are moot. - Some incremental refactoring of the gpiolib core and ACPI GPIO library for more descriptor usage. - Refactor the chained IRQ handler set-up method to handle also threaded, nested interrupts and set up the parent IRQ correctly. Switch STMPE and TC3589x drivers to use this registration method. - Add a .irq_not_threaded flag to the struct gpio_chip, so that also GPIO expanders that block but are still not using threaded IRQ handlers. - New drivers for the ARM64 X-Gene SoC GPIO controller. - The syscon GPIO driver has been improved to handle the "DSP GPIO" found on the TI Keystone 2 SoC:s. - ADNP driver switched to use gpiolib irqchip helpers. - Refactor the DWAPB driver to support being instantiated from and MFD cell (platform device). - Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP, Xilinx and Crystalcove drivers. - Various minor fixes" * tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits) gpio: pch: Build context save/restore only for PM pinctrl: abx500: get rid of unused variable gpio: ks8695: fix 'else should follow close brace '}'' gpio: stmpe: add verbose debug code gpio: stmpe: fix up interrupt enable logic gpio: staticize xway_stp_init() gpio: handle also nested irqchips in the chained handler set-up gpio: set parent irq on chained handlers gpiolib: irqchip: use irq_find_mapping while removing irqchip gpio: crystalcove: support virtual GPIO pinctrl: bcm281xx: make Kconfig dependency more strict gpio: kona: enable only on BCM_MOBILE or for compile testing gpio, bcm-kona, LLVMLinux: Remove use of __initconst gpio: Fix ngpio in gpio-xilinx driver gpio: dwapb: fix pointer to integer cast gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard gpio: xgene: Remove unneeded forward declation for struct xgene_gpio gpio: xgene: Fix missing spin_lock_init() gpio: ks8695: fix switch case indentation gpiolib: add irq_not_threaded flag to gpio_chip ...
2014-10-06mfd: cros_ec: wait for completion of commands that return IN_PROGRESSAndrew Bresticker
When an EC command returns EC_RES_IN_PROGRESS, we need to query the state of the EC until it indicates that it is no longer busy. Do this in cros_ec_cmd_xfer() under the EC's mutex so that other commands (e.g. keyboard, I2C passtru) aren't issued to the EC while it is working on the in-progress command. The 10 milliseconds delay and the number of retries are the values that were used by the flashrom tool when retrying commands. Signed-off-by: Andrew Bresticker <abrestic@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-10-06mfd: cros_ec: move locking into cros_ec_cmd_xferAndrew Bresticker
Now that there's a central cros_ec_cmd_xfer(), move the locking out of the SPI driver. Signed-off-by: Andrew Bresticker <abrestic@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Reviewed-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-10-06mfd: cros_ec: stop calling ->cmd_xfer() directlyAndrew Bresticker
Instead of having users of the ChromeOS EC call the interface-specific cmd_xfer() callback directly, introduce a central cros_ec_cmd_xfer() to use instead. This will allow us to put all the locking and retry logic in one place instead of duplicating it across the different drivers. Signed-off-by: Andrew Bresticker <abrestic@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Reviewed-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-10-06mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_ECDoug Anderson
If someone sends a EC_CMD_REBOOT_EC to the EC, the EC will likely be unresponsive for quite a while. Add a delay to the end of the command to prevent random failures of future commands. NOTES: * This could be optimized a bit by simply delaying the next command sent, but EC_CMD_REBOOT_EC is such a rare command that the extra complexity doesn't seem worth it. * This is a bit of an "ugly hack" since the SPI driver is effectively snooping on the communication and making a lot of assumptions. It would be nice to architect in some better solution long term. * This same logic probably needs to be applied to the i2c driver. Signed-off-by: Doug Anderson <dianders@chromium.org> Reviewed-by: Randall Spangler <rspangler@chromium.org> Reviewed-by: Vadim Bendebury <vbendeb@chromium.org> Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: arizona: Correct mask to allow setting micbias external capCharles Keepax
Currently the mask for the external capacitor bit is missing when writing the MICBIAS config meaning it will never be set this patch fixes this. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: Add ACPI supportMika Westerberg
If an MFD device is backed by ACPI namespace, we should allow subdevice drivers to access their corresponding ACPI companion devices through normal means (e.g using ACPI_COMPANION()). This patch adds such support to the MFD core. If the MFD parent device does not specify any ACPI _HID/_CID for the child device, the child device will share the parent ACPI companion device. Otherwise the child device will be assigned with the corresponding ACPI companion, if found in the namespace below the parent. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26Revert "mfd: wm5102: Manually apply register patch"Charles Keepax
This reverts commit d9d03496f6f904a3588bdb8b215853bc4e50132c. It seems this commit was applied twice, once through ASoC and once through MFD: commit 4c9bb8bc352a14c9613c77bc3f1e9038cd086b9b mfd: wm5102: Manually apply register patch commit d9d03496f6f904a3588bdb8b215853bc4e50132c mfd: wm5102: Manually apply register patch This has lead to a small piece of duplicate code. It is harmless hence how it has gone unoticed for so long. This patch reverts one of the two commits removing the unneeded code. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TSJeff Lance
The logic in AFE_Pen_Ctrl bitmask in the CTRL register is different for five wire versus four or eight wire touschscreens. This patch should fix this for five-wire touch screens. There should be no change needed here for four and eight wire tousch screens. Signed-off-by: Jeff Lance <j-lance1@ti.com> [bigeasy: keep the change mfd only] Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: Inherit coherent_dma_mask from parent deviceBoris BREZILLON
dma_mask and dma_parms are already inherited from the parent device but dma_coherent_mask was left uninitialized (set to zero thanks to kzalloc). Set sub-device coherent_dma_mask to its parent value to simplify sub-drivers making use of dma coherent helper functions (those drivers currently have to explicitly set the dma coherent mask using dma_set_coherent_mask function). Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: Add support for Qualcomm SPMI PMICsJosh Cartwright
The Qualcomm SPMI PMIC chips are components used with the Snapdragon 800 series SoC family. This driver exists largely as a glue mfd component, it exists to be an owner of an SPMI regmap for children devices described in device tree. Signed-off-by: Josh Cartwright <joshc@codeaurora.org> Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: axp209x: Drop the parent supplies fieldMaxime Ripard
Now that the regulator code get its parent supplies purely from the DT, we can drop the parent supplies resources in the MFD driver. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to ↵Nishanth Menon
support system power off ti,system-power-controller is more or less the standard way of indicating that the PMIC is the system wide power controller and hence may be used to switch off the system. Almost ALL TI PMIC drivers and many Maxim PMIC drivers follow the same style. So support 'ti,system-power-controller' in addition to the usual 'ti,use_poweroff' to indicate that the PMIC instance has control for switching off the system. Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: rk808: Add register cachingDoug Anderson
Let's define the voltatile registers (those that can't be cached) and enable caching. The rk808 is accessed almost constantly with cpufreq so this is really nice. As measured by ftrace: before this change: cpu0_set_target() => ~2200us after this change: cpu0_set_target() => ~500us Signed-off-by: Doug Anderson <dianders@chromium.org> Reviewed-by: Chris Zhong <zyw@rock-chips.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: arizona: Use handle_simple_irq for IRQ dispatch chipCharles Keepax
We use a dummy IRQ chip to dispatch interrupts to the two seperate IRQ domains on the Arizona devices. This is just a simple software IRQ chip and thus the current handle_edge_irq is unnecessary for its needs. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: max14577: Don't pass IRQ domain to mfd_add_devicesKrzysztof Kozlowski
The max14577 MFD cells do not have any resources so the IRQ domain passed to mfd_add_devices is not used. Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: stmpe: Support gpio over irq under device treeSean Cross
The stmpe_platform_data has a irq_over_gpio field, which allows the system to read STMPE events whenever an IRQ occurs on a GPIO pin. This patch adds the ability to configure this field and to use a GPIO as an IRQ source for boards configuring the STMPE in device tree. Signed-off-by: Sean Cross <xobs@kosagi.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: intel_soc_pmic: Add CONFIG_PM_SLEEP check for suspend_fn/resume_fnJaewon Kim
This patch fix warning message with CONFIG_PM_SLEEP disabled If CONFIG_PM_SLEEP is not enabled we receive the following warning message: drivers/mfd/intel_soc_pmic_core.c:118:12: warning: 'intel_soc_pmic_suspend' defined but not used Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: rtsx_pcr: Fix MSI enable error handlingChris Ball
pci_enable_msi() can return failure with both positive and negative integers -- it returns 0 for success -- but is only tested here for "if (ret < 0)". This causes us to try to use MSI on the RTS5249 SD reader in the Dell XPS 11 when enabling MSI failed, causing: [ 1.737110] rtsx_pci: probe of 0000:05:00.0 failed with error -110 Cc: stable <stable@vger.kernel.org> Reported-by: D. Jared Dominguez <Jared_Dominguez@Dell.com> Tested-by: D. Jared Dominguez <Jared_Dominguez@Dell.com> Signed-off-by: Chris Ball <chris@printf.net> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: ti_am335x_tscadc: Fix TSC resumeSebastian Andrzej Siewior
In the resume path, the ADC invokes am335x_tsc_se_set_cache() with 0 as the steps argument if continous mode is not in use. This in turn disables all steps and so the TSC is not working until one ADC sampling is performed. This patch fixes it by writing the current cached mask instead of the passed steps. Fixes: 7ca6740cd1cd ("mfd: input: iio: ti_amm335x: Rework TSC/ADCA synchronization") Cc: stable@vger.kernel.org # v3.13+ Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: tps65217: Tell regmap what registers are validMark Brown
Allow regmap to provide debugfs access to the register map by telling it what registers are valid. Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: mc13xxx: Configure WDI resetMarkus Pargmann
Setup the PMIC to make a restart when a watchdog interrupt occures. If this is not configured, the PMIC will shut down the power supply without a restart. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: pcf50633: Use sprintf directlyAndy Shevchenko
When dump a content of the registers let's use snprintf() directly with %*ph specifier. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: Add HI6421 PMIC Core driverGuodong Xu
This adds driver to support HiSilicon Hi6421 PMIC. Hi6421 includes multi- functions, such as regulators, codec, ADCs, Coulomb counter, etc. This driver includes core APIs _only_. Drivers for individul components, like voltage regulators, are implemented in corresponding driver directories and files. Registers in Hi6421 are memory mapped, so using regmap-mmio API. Signed-off-by: Guodong Xu <guodong.xu@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: lpc_sch: Remove FSF addressAndy Shevchenko
This patch removes FSF address because it can be changed. While here, update the copyright lines by adding Intel Corp. to them. There is no functional change. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: lpc_sch: Add support for Intel Quark X1000Andy Shevchenko
Intel Quark X1000 SoC supports IRQ based GPIO. This patch will enable MFD support for Quark X1000 and provide IRQ resources to Quark X1000 GPIO device driver. Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com> Tested-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: lpc_sch: Reduce duplicate code and improve manageabilityAndy Shevchenko
This patch refactors the driver to use helper functions instead of copy'n'pasted pieces of code. It also introduces an additional struct to hold a chipset info. The chipset info will be used to store features that are supported by specific processor or chipset. LPC_SCH supports SMBUS, GPIO and WDT features. As this code base might expand further to support more processors, this implementation will help to keep code base clean and manageable. The patch is partially based on the work done by Chang Rebecca Swee Fun. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: RK808: Add new mfd driver for RK808Chris Zhong
The RK808 chip is a power management IC for multimedia and handheld devices. It contains the following components: - Regulators - RTC - Clkout The RK808 core driver is registered as a platform driver and provides communication through I2C with the host device for the different components. Signed-off-by: Chris Zhong <zyw@rock-chips.com> Signed-off-by: Zhang Qing <zhangqing@rock-chips.com> Tested-by: Heiko <heiko@sntech.de> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: da9052: Avoid setting read_flag_mask for da9052-i2c driverAxel Lin
Current code init regmap with &da9052_regmap_config for both da9052-spi and da9052-i2c drivers. da9052-spi sets the read_flag_mask. The same setting may be applied for da9052-i2c if da9052-spi driver is loaded first because they actually use the same regmap_config setting. Fix this issue by using a local variable for regmap_config in da9052-spi driver, so the settings in spi driver won't impact the settings in i2c driver. Also makes da9052_regmap_config const to avoid similar issue. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: arizona: Propagate irq_wake through to parent IRQCharles Keepax
If one of the internal Arizona IRQs is set as a wake source this needs to be propogated back to the actual IRQ line that the Arizona device is attached to. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: arizona: Add support for INn_Mode register controlInha Song
Some boards need to set the INn_MODE[1:0] register to change the input signal patch. This wlf,inmode property is optional. If present, values must be specified less than or equal to the number of input singals. If values less than the number of input signals, elements that has not been specifed are set to 0 by default. Example: - wlf,inmode = <2 0 2>; /* IN1, IN3 use DMIC */ Signed-off-by: Inha Song <ideal.song@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: arizona: Add ASYNC_SAMPLE_RATE_2 registersCharles Keepax
Some arizona devices have a second asynchronous sample rate, add the registers necessary to support this. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Acked-by: Mark Brown <broonie@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: Add Ricoh RN5T618 PMIC core driverBeniamino Galvani
Ricoh RN5T618 is a power management IC which integrates 3 step-down DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, fuel gauge, ADC, GPIOs and a watchdog timer. This commit adds a MFD core driver to support the I2C communication with the device. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: ti_am335x_tscadc: Fix TSC operation after ADC continouous modeVignesh R
After enabling and disabling ADC continuous mode via sysfs, ts_print_raw fails to return any data. This is because when ADC is configured for continuous mode, it disables touch screen steps.These steps are not re-enabled when ADC continuous mode is disabled. Therefore existing values of REG_SE needs to be cached before enabling continuous mode and disabling touch screen steps and enabling ADC steps. The cached value are to be restored to REG_SE once ADC is disabled. Fixes: 7ca6740cd1cd ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization") Cc: stable@vger.kernel.org # v3.13+ Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: tps65910: Work around silicon erratum SWCZ010Arnout Vandecappelle (Essensium/Mind)
http://www.ti.com/lit/pdf/SWCZ010: Glitch on SDA-SCL not managed correctly by the I2C IP Impact: The standard specifies that the I2C transfer should restart on a start event in all cases. The current design does not support two consecutive Start conditions. This can cause the first real access after such a glitch to be corrupted. Description: An unexpected glitch on SDA and SCL can generate a wrong start event. In the current design, the SCL line must toggle two times to detect a new start event and completely restart the I2C access; hence the real start event is not detected in the case of a single SCL toggle. Workaround: Repeat I2C access. A simpler workaround is to make a dummy transfer just before the first access to the tps65910 chip. This can be done unconditionally. Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be> Acked-by: Mark Brown <broonie@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: stmpe: Rid variable length array Sparse warningsLee Jones
Numbers are generated by taking the largest currently used values. drivers/mfd/stmpe.c:252:17: warning: Variable length array is used. drivers/mfd/stmpe.c:857:16: warning: Variable length array is used. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: max8925-i2c: Fix variable length array Sparse warningLee Jones
The largest byte size in use currently is 8. Fix array size to 9. drivers/mfd/max8925-i2c.c:40:33: warning: Variable length array is used Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: 88pm860x-i2c: Fix variable length array Sparse warningLee Jones
drivers/mfd/88pm860x-i2c.c:125:33: warning: Variable length array is used. Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: 88pm860x-i2c: Purge unused functionsLee Jones
The following functions appear to be unused since v2.6.39: pm860x_page_reg_read() pm860x_page_bulk_write() pm860x_page_set_bits() Let's remove them. Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: lpc_ich: Add Device IDs for Intel 9 Series PCHJames Ralston
This patch adds the LPC Device IDs for the Intel 9 Series PCH. Signed-off-by: James Ralston <james.d.ralston@intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: max77693: Improve support for the flash cellJacek Anaszewski
This patch improves support for the flash cell of max77693 mfd by adding relevant of_compatible field and a structure for caching related platform data. Added are also FLASH registers related macro definitions. Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-02 10:19:44 +0000