summaryrefslogtreecommitdiffstats
path: root/drivers/mmc/host/mmci.c
AgeCommit message (Collapse)Author
2011-10-28Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits) mmc: fix compile error when CONFIG_BLOCK is not enabled mmc: core: Cleanup eMMC4.5 conditionals mmc: omap_hsmmc: if multiblock reads are broken, disable them mmc: core: add workaround for controllers with broken multiblock reads mmc: core: Prevent too long response times for suspend mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00 mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode mmc: core: support HPI send command mmc: core: Add cache control for eMMC4.5 device mmc: core: Modify the timeout value for writing power class mmc: core: new discard feature support at eMMC v4.5 mmc: core: mmc sanitize feature support for v4.5 mmc: dw_mmc: modify DATA register offset mmc: sdhci-pci: add flag for devices that can support runtime PM mmc: omap_hsmmc: ensure pbias configuration is always done mmc: core: Add Power Off Notify Feature eMMC 4.5 mmc: sdhci-s3c: fix potential NULL dereference mmc: replace printk with appropriate display macro mmc: core: Add default timeout value for CMD6 mmc: sdhci-pci: add runtime pm support ...
2011-10-26mmc: replace printk with appropriate display macroGirish K S
All the files using printk function for displaying kernel messages in the mmc driver have been replaced with corresponding macro. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: mmci: simplify err check in mmci_post_requestPer Forlin
The error condition indicates that mmci_post_request() should cleanup after the mmci_pre_request(). In this case the resources allocated by device_prep_slave_sg() are freed by calling dmaengine_terminate_all(). dma_unmap_sg() should always be performed if the host_cookie is set. Signed-off-by: Per Forlin <per.forlin@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-09-27clk: mmci: convert to clk_prepare()/clk_unprepare()Russell King
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-09-22PM: add runtime PM support to MMCIRussell King
Add runtime PM support to the MMCI primecell driver, making use of the core primecell bus runtime PM support. Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-07-24Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits) ARM: 7004/1: fix traps.h compile warnings ARM: 6998/2: kernel: use proper memory barriers for bitops ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM ARM: Fix build errors caused by adding generic macros ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU ARM: CPU hotplug: pass in proper affinity mask on IRQ migration ARM: GIC: avoid routing interrupts to offline CPUs ARM: CPU hotplug: fix abuse of irqdesc->node ARM: 6981/2: mmci: adjust calculation of f_min ARM: 7000/1: LPAE: Use long long printk format for displaying the pud ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence ARM: ARM_DMA_ZONE_SIZE is no more ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size ...
2011-07-22Merge branches 'btc', 'dma', 'entry', 'fixes', 'linker-layout', 'misc', ↵Russell King
'mmci', 'suspend' and 'vfp' into for-next
2011-07-20mmc: mmci: implement pre_req() and post_req()Per Forlin
pre_req() runs dma_map_sg() and prepares the dma descriptor for the next mmc data transfer. post_req() runs dma_unmap_sg. If not calling pre_req() before mmci_request(), mmci_request() will prepare the cache and dma just like it did it before. It is optional to use pre_req() and post_req() for mmci. Signed-off-by: Per Forlin <per.forlin@linaro.org> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-19ARM: 6981/2: mmci: adjust calculation of f_minLinus Walleij
The ARM version maximum clock divider is 512 whereas for the ST variants it's 257. Let's use DIV_ROUND_UP() for both cases so we can see clearly what's going on here. [Use DIV_ROUND_UP to clarify elder code] Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Reviewed-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-07-06ARM: 6980/1: mmci: use StartBitErr to detect bad connectionsLinus Walleij
Stresstesting insert/remove of SD-cards can trigger a StartBitErr. This made the driver to hang in forever waiting for a non ocurring data timeout. This bit and interrupt is documented in the original PL180 TRM, just never implemented until now. Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Reviewed-by: Linus Walleij <linus.walleij@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-06-06ARM: 6894/1: mmci: trigger card detect IRQs on falling and rising edgesLinus Walleij
Right now the card detect IRQ for MMCI is requested without any flags which will give some default machine-specified IRQ behaviour. However on the U300 rising+falling edges (such as can be expected from a simple GPIO to generate when inserting/removing a card) need to be requested explicitly. Cc: Rabin Vincent <rabin.vincent@stericsson.com> Cc: Ulf Hansson <ulf.hansson@stericsson.com> Cc: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-05-26ARM: 6832/1: mmci: support for ST-Ericsson db8500v2Philippe Langlais
ST-Ericsson modified ARM PrimeCell PL180 block has not got an updated corresponding amba-id, althought the IP block has changed in db8500v2. The change was done to the datactrl register. Using the overrided subversion ID, account for this. Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-05-12ARM: 6858/1: mmci: force negative edge on clock bypass for ux500Linus Walleij
This fixes a regression on high clock speeds with the MMCI on ux500. We need to make sure we derive the passthru clock on the falling edge of the incoming clock if it shall work at high frequencies, and on the ux500's there is a special bit for this. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-05-11ARM: 6785/1: mmci: separate out ST Micro register definesLinus Walleij
The mmci.h header contained a few registers not clearly marked as ST Micro only, rectify this and remove the HWFC magic in the process. The idea is to make the mmci.h header file more ordered so other vendors with PL180 derivates can see where to put in their custom register defines. Includes portions of an earlier patch from Sebastian Rasmussen. Acked-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-03-25mmc: mmci: Add ARM variant with extended FIFOPawel Moll
New IO FPGA implementation for Versatile Express boards contain MMCI (PL180) cell with FIFO extended to 128 words (512 bytes). Matt Waddel reports that this patch improves MMC performance on his vexpress system, and also fixes "mmcblk0: error -5 transferring data" errors. Signed-off-by: Pawel Moll <pawel.moll@arm.com> Tested-by: Matt Waddel <matt.waddel@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-03-17Merge branches 'aaci', 'mmci-dma', 'pl' and 'pl011' into driversRussell King
2011-02-23ARM: amba: make probe() functions take const id tablesRussell King
Make Primecell driver probe functions take a const pointer to their ID tables. Drivers should never modify their ID tables in their probe handler. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04ARM: mmci: add dmaengine-based DMA supportRussell King
Based on a patch from Linus Walleij. Add dmaengine based support for DMA to the MMCI driver, using the Primecell DMA engine interface. The changes over Linus' driver are: - rename txsize_threshold to dmasize_threshold, as this reflects the purpose more. - use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'. - clean up requesting of dma channels. - don't release a single channel twice when it's shared between tx and rx. - get rid of 'dma_enable' bool - instead check whether the channel is NULL. - detect incomplete DMA at the end of a transfer. Some DMA controllers (eg, PL08x) are unable to be configured for scatter DMA and also listen to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI. They can do one or other but not both. As MMCI uses LBREQ/LSREQ for the final burst/words, PL08x does not transfer the last few words. - map and unmap DMA buffers using the DMA engine struct device, not the MMCI struct device - the DMA engine is doing the DMA transfer, not us. - avoid double-unmapping of the DMA buffers on MMCI data errors. - don't check for negative values from the dmaengine tx submission function - Dan says this must never fail. - use new dmaengine helper functions rather than using the ugly function pointers directly. - allow DMA code to be fully optimized away using dma_inprogress() which is defined to constant 0 if DMA engine support is disabled. - request maximum segment size from the DMA engine struct device and set this appropriately. - removed checking of buffer alignment - the DMA engine should deal with its own restrictions on buffer alignment, not the individual DMA engine users. - removed setting DMAREQCTL - this confuses some DMA controllers as it causes LBREQ to be asserted for the last seven transfers, rather than six SREQ and one LSREQ. - removed burst setting - the DMA controller should not burst past the transfer size required to complete the DMA operation. Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04ARM: mmci: no need for separate host->data_xferedRussell King
We don't need to store the number of bytes transferred in our host structure - we can store this directly in data->bytes_xfered. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04ARM: mmci: avoid unnecessary switch to data available PIO interruptsRussell King
We don't need to switch to data available interrupts if there's at least half a FIFO depth worth of data remaining, as we'll still get the FIFO half full interrupt. Keep this interrupt masked off until we have less than half the FIFO depth worth of data remaining. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04ARM: mmci: no need to call flush_dcache_page() with sg_miter APIRussell King
The sg_miter API provides the required cache maintainence, so we don't need to do that ourselves. Remove the unnecessary additional cache maintainence. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04ARM: mmci: avoid reporting too many completed bytes on fifo overrunRussell King
The data counter counts the number of bytes transferred on the MMC bus. When a FIFO overrun occurs, we will not have transferred a FIFOs-worth of data to memory, and so the data counter will be a FIFOs-worth ahead. If this occurs on a block boundary, we will report one too many sectors as successful. Fix this. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-01-31ARM: mmci: round down the bytes transferred on errorRussell King
We should not report incomplete blocks on error. Return the number of bytes successfully transferred, rounded down to the nearest block. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-01-31ARM: mmci: complete the transaction on errorRussell King
When we encounter an error, make sure we complete the transaction otherwise we'll leave the request dangling. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-01-27ARM: 6642/1: mmci: calculate remaining bytes at error correctlyLinus Walleij
The MMCIDATACNT register contain the number of byte left at error not the number of words, so loose the << 2 thing. Further if CRC fails on the first block, we may end up with a negative number of transferred bytes which is not good, and the formula was in wrong order. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-01-25mmc: mmci: don't read command response when invalidRussell King - ARM Linux
Don't read the command response from the registers when either the command timed out (because there was no response from the card) or the checksum on the response was invalid. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-01-24ARM: 6632/3: mmci: stop using the blockend interruptsLinus Walleij
Implement a suggestion from Russell to drop the use of blockend interrupts altogether and instead rely on the data counter. Tested with error-free cards on U300, U8500 and RealView PB1176. Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-12-30ARM: mmci: Clean up MMCI announcement printkRussell King
Make the MMCI announcement printk say which primecell part number has been found. Display the revision as an unsigned decimal, and display only the first 8 hex digits of the base address unless it's larger. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-12-19ARM: 6530/1: mmci: partially revert clock divisor codeLinus Walleij
I misread the datasheet as if bypass mode was not available at all on the ux500's, I was wrong. It is there, the datasheet just states that you should not have to use it. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-12-19ARM: 6526/1: mmci: corrected calculation of clock div for ux500Linus Walleij
The Ux500 variant of this block has a different divider. The value used right now is too big and which means a loss in performance. This fix corrects it. Also expand the math comments a bit so it's clear what's happening. Further the Ux500 variant does not like if we use the BYPASS bit, instead we are supposed to set the clock divider to zero. Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-11-10ARM: 6438/2: mmci: add SDIO support for ST VariantsLinus Walleij
This adds some minor variant data and trickery to enable SDIO on the ST Micro variants of MMCI/PL180. Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-11-10ARM: 6399/3: mmci: handle broken MCI_DATABLOCKEND hardwareLinus Walleij
On the U300 the MCI_DATAEND and MCI_DATABLOCKEND IRQs can arrive out-of-order. Replace an ugly #ifdef hack with a proper runtime solution which models what is really happening. In the U300 DMA mode and on all Ux500 models, the MCI_DATABLOCKEND flag isn't properly cleared in hardware following and ACK leading to all kind of weird behaviour when the flag is still up in subsequent interrupts, so we add two flags indicating the error and handle this runtime. Cc: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-11-10ARM: 6311/2: mmci: work with only one irqLinus Walleij
The DBx500 variants have only one IRQ line hooked up. Allow these (and any other implementations which choose to use only one irq) to work by directing the PIO interrupts also to the first IRQ line. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-10-23mmc: Move regulator handling closer to coreLinus Walleij
After discovering a problem in regulator reference counting I took Mark Brown's advice to move the reference count into the MMC core by making the regulator status a member of struct mmc_host. I took this opportunity to also implement NULL versions of the regulator functions so as to rid the driver code from some ugly #ifdef CONFIG_REGULATOR clauses. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Tony Lindgren <tony@atomide.com> Cc: Adrian Hunter <adrian.hunter@nokia.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Sundar Iyer <sundar.iyer@stericsson.com> Cc: Daniel Mack <daniel@caiaq.de> Cc: Pierre Ossman <pierre@ossman.eu> Cc: Matt Fleming <matt@console-pimps.org> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Cliff Brake <cbrake@bec-systems.com> Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc: Remove distinction between hw and phys segmentsMartin K. Petersen
We have deprecated the distinction between hardware and physical segments in the block layer. Consolidate the two limits into one in drivers/mmc/. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-09-23ARM: 6370/1: mmci: use _cansleep GPIO functionsLinus Walleij
Currently the kernel is screaming about slowpath at me for the wp/cd callbacks. Switch to the _cansleep variants so as to silence this. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-09-23ARM: 6309/1: mmci: allow neither ->status nor gpio_cd to be specifiedRabin Vincent
The card may be always present on the board, and for these cases neither a status callback nor a card detect GPIO is required, and card detection polling can be disabled. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-09-23ARM: 6308/1: mmci: support card detection interruptsRabin Vincent
If an IRQ can be requested on the card detected GPIO, use it instead of polling. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-08-26ARM: 6310/1: mmci: support different FIFO sizesRabin Vincent
The Ux500 variant has a 32-word FIFO (TXFIFOEMPTY is asserted when it has 2 left) and TXFIFOHALFEMPTY is repurposed as TXFIFOBURSTWRITEABLE, with a burst being defined as 8-words. Likewise for RX. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-08-26ARM: 6307/1: mmci: allow the card detect GPIO value not to be invertedRabin Vincent
On some platforms, the GPIO value from the gpio_cd pin doesn't need to be inverted to get it active high. Add a cd_invert platform data parameter and change existing platforms using GPIO for CD (only Realview) to enable it. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-08-03Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (291 commits) ARM: AMBA: Add pclk support to AMBA bus infrastructure ARM: 6278/2: fix regression in RealView after the introduction of pclk ARM: 6277/1: mach-shmobile: Allow users to select HZ, default to 128 ARM: 6276/1: mach-shmobile: remove duplicate NR_IRQS_LEGACY ARM: 6246/1: mmci: support larger MMCIDATALENGTH register ARM: 6245/1: mmci: enable hardware flow control on Ux500 variants ARM: 6244/1: mmci: add variant data and default MCICLOCK support ARM: 6243/1: mmci: pass power_mode to the translate_vdd callback ARM: 6274/1: add global control registers definition header file for nuc900 mx2_camera: fix type of dma buffer virtual address pointer mx2_camera: Add soc_camera support for i.MX25/i.MX27 arm/imx/gpio: add spinlock protection ARM: Add support for the LPC32XX arch ARM: LPC32XX: Arch config menu supoport and makefiles ARM: LPC32XX: Phytec 3250 platform support ARM: LPC32XX: Misc support functions ARM: LPC32XX: Serial support code ARM: LPC32XX: System suspend support ARM: LPC32XX: GPIO, timer, and IRQ drivers ARM: LPC32XX: Clock driver ...
2010-07-30ARM: Fix Versatile/Realview/VExpress MMC card detection senseRussell King
The MMC card detection sense has become really confused with negations at various levels, leading to some platforms not detecting inserted cards. Fix this by converting everything to positive logic throughout, thereby getting rid of these negations. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-29ARM: 6246/1: mmci: support larger MMCIDATALENGTH registerRabin Vincent
The Ux500 variant has a 24-bit MMCIDATALENGTH register, as opposed to the 16-bit one on the ARM version. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-29ARM: 6245/1: mmci: enable hardware flow control on Ux500 variantsRabin Vincent
Although both the U300 and Ux500 use ST variants, the HWFCEN bits are at different positions, so use the variant_data to store the information. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-29ARM: 6244/1: mmci: add variant data and default MCICLOCK supportRabin Vincent
Add a variant_data structure to handle the differences between the various variants of this peripheral. Add a first quirk for a default MCICLOCK value, required on the Ux500 variant where the enable bit needs to be always set, since it controls access to some registers. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-29ARM: 6243/1: mmci: pass power_mode to the translate_vdd callbackRabin Vincent
Platforms may have some external power control which need to be controlled from board specific code. Rename the translate_vdd() callback to vdd_handler() and pass it the power mode. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-27ARM: 6239/1: mmci: let core poll for card detectionRabin Vincent
Use the MMC core's ability to poll for card detection. This also has the advantage of doing the gpio_get_value from a workqueue instead of timer, allowing the gpio to be on a sleeping gpiochip. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-27ARM: 6238/1: mmci: fix multi block transfersRabin Vincent
Fix the data transfer size to allow multi block transfers to work. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-27ARM: 6237/1: mmci: use sg_miter API to fix multi-page sg handlingRabin Vincent
The mmci driver's SG list iteration logic assumes that each SG entry spans only one page, and only maps and flushes one page of the sg. This is not a valid assumption. Fix it by converting the driver to the sg_miter API, which correctly handles sgs which span multiple pages. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-05-27mmc: remove the "state" argument to mmc_suspend_host()Matt Fleming
Even though many mmc host drivers pass a pm_message_t argument to mmc_suspend_host() that argument isn't used the by MMC core. As host drivers are converted to dev_pm_ops they'll have to construct pm_message_t's (as they won't be passed by the PM subsystem any more) just to appease the mmc suspend interface. We might as well just delete the unused paramter. Signed-off-by: Matt Fleming <matt@console-pimps.org> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Acked-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>ZZ Acked-by: Sascha Sommer <saschasommer@freenet.de> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-30 23:33:22 +0000