| Age | Commit message (Collapse) | Author |
|---|
|
For better code reuse use the newly added page iterator to iterate
through the pages. The offset, length within the page is still
calculated by the mapping iterator as well as the actual mapping. Idea
from Tejun Heo.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.9:
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"
* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS updates from Samuel Ortiz:
"This is the MFD pull request for the 3.9 merge window.
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data
consolidation, OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee
Jones. In particular, the debugfs and the sysct interfaces got
extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the
twl-core driver, with a much needed module id lookup code
improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the
palmas GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra
and Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and
ab9540 based devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to
Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a
better card detection code path and now also supports the RTS5227
chipset, thanks to Wei Wang and Roger Tseng."
* tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (109 commits)
mfd: lpc_ich: Use devres API to allocate private data
mfd: lpc_ich: Add Device IDs for Intel Wellsburg PCH
mfd: lpc_sch: Accomodate partial population of the MFD devices
mfd: da9052-i2c: Staticize da9052_i2c_fix()
mfd: syscon: Fix sparse warning
mfd: twl-core: Fix kernel panic on boot
mfd: rtsx: Fix issue that booting OS with SD card inserted
mfd: ab8500: Fix compile error
mfd: Add missing GENERIC_HARDIRQS dependecies
Documentation: Add docs for max8925 dt
mfd: max8925: Add dts
mfd: max8925: Support dt for backlight
mfd: max8925: Fix onkey driver irq base
mfd: max8925: Fix mfd device register failure
mfd: max8925: Add irqdomain for dt
mfd: vexpress: Allow vexpress-sysreg to self-initialise
mfd: rtsx: Support RTS5227
mfd: rtsx: Implement driving adjustment to device-dependent callbacks
mfd: vexpress: Add pseudo-GPIO based LEDs
mfd: ab8500: Rename ab8500 to abx500 for hwmon driver
...
|
|
Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Rework the driver to parse the device tree
directly into struct sdhci_tegra.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Some SD/MMC interfaces use 2 power regulators: one to power the card itself
(Vcc) and another one to pull signal lines up (VccQ). In case of eMMC and
UHS SD cards the regulators also have to be configured to supply different
voltages. The preferred order of turning supply power on and off is to
turn Vcc first on and last off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Use managed allocations to get memory, clock and interrupts . This
significantly simplifies clean up paths.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The struct sh_mobile_sdhi_info::pdata field was only used for platform-
based card detection and isn't used anymore since the migration to GPIO-
based MMC slot functions. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add parsing of common and driver-specific DT bindings to the tmio-mmc
MMC host driver and the sh_mobile_sdhi interface layer.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Use mmc_of_parse() to get interface capability flags and used GPIOs from
device-tree bindings.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
tmio-mmc platform flags can be set by various means, including caller
drivers and device-tree bindings, therefore it is better to only check
them in the tmio-mmc driver proper, not in caller drivers themselves.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
3714f4315354 ("mmc: sdhci: update signal voltage switch code") changed the
type of the second parameter of sdhci_do_start_signal_voltage_switch(),
from "struct mmc_ios *ios" to "int signal_voltage" which causes the
following build warning:
drivers/mmc/host/sdhci.c:2044:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/mmc/host/sdhci.c:2044:2: warning: (near initialization for 'sdhci_ops.start_signal_voltage_switch') [enabled by default]
Use the previous type so that it matches the start_signal_voltage_switch()
definition from host.h.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Some regulators don't report any voltage values, so checking supported
voltage range results in disabling all SDHCI_CAN_VDD_* flags and
registration failure. This patch finally provides a correct fix for the
registration of SDHCI driver with all possible voltage regulators:
dummy, fixed and regulated without using regulator_count_voltages()
hacks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK does basically the same as
implementing struct sdhci_ops .get_timeout_clock, so simply set that
quirk and remove the custom code to simplify the driver.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Several new models of readers use different way to select driving
capability (a necessary adjustment along with voltage change). Removing
this from device-independent rtsx_pci_sdmmc module. It will be implemented
in device-depend calls encapsulated by rtsx_pci_switch_output_voltage().
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Reviewed-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
4d55c5a1 ("mmc: sdhci: enable preset value after uhs initialization")
added preset value support and enabled it by default during sd card init.
Below are the enhancements introduced by this patch:
1. In current code, preset value is enabled after setting clock finished,
which means the clock is manually set by driver firstly and then suddenly
switched to preset value at this point. So the first setting is useless
and unnecessary. What's more, the first clock setting may differ from the
preset one. The better way is enable preset value just after switch to
UHS mode so the preset value can take effect immediately. So move preset
value enable from mmc_sd_init_card to sdhci_set_ios which will be called
during set timing.
2. In current code, preset value is disabled at the beginning of
mmc_attach_sd. It's too late since low freq (400khz) should be set in
mmc_power_up. So move preset value disable to sdhci_set_ios which will
be called during power up.
3. host->clock and ios->drv_type should also be updated according to the
preset value if it's enabled. Current code missed this.
4. This patch also introduce a quirk to disable preset value in case
preset value doesn't work.
This patch has been verified on sdhci-pxav3 platform with both preset
enabled and disabled.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When irq_of_parse_and_map() returns an error, it does as zero. But in
mmc_spi_get_pdata(), the error return case is compared against NO_IRQ.
This might work where NO_IRQ is zero (defaults to zero when undefined,
as on MIPS) but not where NO_IRQ is different, e.g. on ARM where it's -1.
This patch changes to comparison with 0 which is the error return value
of irq_of_parse_and_map().
Tested on ARM that mmc_spi is working now.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Quite a few drivers have a implementation of the get_timeout_clock
callback which simply returns the result of clk_get_rate on the device's
clock. This patch adds a common implementation of this to the sdhci-pltfm
module and replaces all custom implementations with the common one.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The protocol related code is moved to core stack. So update the host
driver accordingly.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Tim Wang <wangtt@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This driver handles the virtual MMC device present in the Goldfish emulator.
The patch folds together initial work from Mike Lockwood and patches by
San Mehat, Jun Nakajima and Tom Keel <thomas.keel@intel.com> plus cleanups
by Alan Cox to get it all into 3.6 shape.
Signed-off-by: Mike A. Chan <mikechan@google.com>
[cleaned up and x86 support added]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Xiaohui Xin <xiaohui.xin@intel.com>
Signed-off-by: Jun Nakajima <jun.nakajima@intel.com>
Signed-off-by: Bruce Beare <bruce.j.beare@intel.com>
[Moved to 3.4]
Signed-off-by: Tom Keel <thomas.keel@intel.com>
[Moved to 3.7]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The i.MX esdhc has a nonstandard bit layout for the SDHCI_HOST_CONTROL
register. To support 8bit bus width on i.MX populate the platform_bus_width
callback. This is tested on an i.MX25, but should according to the datasheets
work on the other i.MX using this hardware aswell. The i.MX6, while having
a SDHCI_SPEC_300 controller, still uses the same nonstandard register layout.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The 8bit in the function name is misleading. When set, it will be
used to set the bus width, regardless of whether 8bit or another
bus width is requested, so change the function name to
platform_bus_width.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
SDHCI core will try to use Auto CMD23 for mmc card. Currently, we will
see the following message with mmc card on usdhc due to the lacking of
Auto CMD23 support in the driver.
$ mmc0: new high speed MMC card at address 0001
mmcblk1: mmc0:0001 MMC02G 1.87 GiB
mmcblk1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
mmcblk1: retrying using single block read
mmcblk1:
Enable Auto CMD23 support for usdhc so that mmc card can work in
multiple block mode.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
It's another violation to SDHC spec that software reset on usdhc
does not reset MIX_CTRL register. Have to do it manually, otherwise
the preserving of the register bits (e.g. AC23EN) may cause mmc card
fail to be initialized.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The combining of SDHCI_TRANSFER_MODE and SDHCI_COMMAND writes is only
required for esdhc, but not necessarily for usdhc. Different from
esdhc where the bits for transfer mode and command are all in the same
register CMD_XFR_TYP, usdhc has a newly introduced register MIX_CTRL
to hold transfer mode bits. So it makes more sense to separate transfer
mode from command write for usdhc.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
3f175a6e5 (mmc: sdhci-esdhc-imx: remove ESDHC_CD_GPIO handling from IO
accessory) introduced the following build warnings:
drivers/mmc/host/sdhci-esdhc-imx.c:149:30: warning: unused variable 'boarddata' [-Wunused-variable]
drivers/mmc/host/sdhci-esdhc-imx.c:181:30: warning: unused variable 'boarddata' [-Wunused-variable]
Remove the unused variables.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Rename esdhc local definitions with ESDHC_ rather than SDHCI_ prefix,
so that we can distinguish them from SDHCI core definitions from name.
A couple of bit fields are also changed use shift for consistency and
better readability.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
SDHCI_CTRL_D3CD is not a standard SDHCI_HOST_CONTROL, so there is no
need to check it in SDHCI_HOST_CONTROL write at all. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When commit 95a2482 (mmc: sdhci-esdhc-imx: add basic imx6q usdhc
support) works around host version issue on imx6q, it gets the
register address fixup "reg ^= 2" lost for imx25/35/51/53 esdhc.
Thus, the controller version on these SoCs is wrongly identified
as v1 while it's actually v2.
Add the address fixup back and take a different approach to correct
imx6q host version, so that the host version read gets back to work
for all SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
With the __devinit/__devexit attributes having been removed, this
__exitp attribute causes an unused function warning and should be
removed as well.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The original quirk was added in the change 'mmc: dw_mmc: add quirk to
indicate missing write protect line'. The original quirk was added at
a controller level even though each slot has its own write protect (so
the quirk should be at the slot level). A recent change (mmc: dw_mmc:
Add "disable-wp" device tree property) added a slot-level quirk and
support for the quirk directly to dw_mmc.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
On some SoCs (like exynos5250) you need to use an external GPIO for
write protect. Add support for wp-gpios to the core dw_mmc driver
since it could be useful across multiple SoCs.
With this change I am able to make use of the write protect for the
external SD slot on exynos5250-snow.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The exynos code claimed the write protect with devm_gpio_request() but
never did anything with it. That meant that anyone using a write
protect GPIO would effectively be write protected all the time.
The handling for wp-gpios belongs in the main dw_mmc driver and has
been moved there.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The "disable-wp" property is used to specify that a given SD card slot
doesn't have a concept of write protect. This eliminates the need for
special case code for SD slots that should never be write protected
(like a micro SD slot or a dev board).
The dw_mmc driver is special in needing to specify "disable-wp"
because the lack of a "wp-gpios" property means to use the special
purpose write protect line. On some other mmc devices the lack of
"wp-gpios" means that write protect should be disabled.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Fixes the following warning when building with W=1 option:
drivers/mmc/host/mxs-mmc.c: In function 'mxs_mmc_adtc':
drivers/mmc/host/mxs-mmc.c:401:2: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
The warning happens because 'i' is used in 'for_each_sg(sgl, sg, sg_len, i)' and should be made unsigned.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add an entry for MODULE_ALIAS().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
On many Marvell SoCs, the pins used for the SDIO interface are part of
the MPP pins, that are muxable pins. In order to get the muxing of
those pins correct, this commit integrates the mvsdio driver with the
pinctrl infrastructure by calling devm_pinctrl_get_select_default()
during ->probe().
Note that we permit this function to fail because not all Marvell
platforms have yet been fully converted to using the pinctrl
infrastructure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
|
|
|
|
Realtek card reader supports both SD and MS card. According to the
settings of rtsx MFD driver, SD host will be probed before MS host.
If we boot/reboot Linux with SD card inserted, the resetting flow of SD
card will succeed, and the following resetting flow of MS is sure to fail.
Then MS upper-level driver will ask rtsx driver to turn power off. This
request leads to the result that the following SD commands fail and SD card
can't be accessed again.
In this commit, Realtek's SD and MS host driver will check whether the card
that upper driver requesting is the one existing in the slot. If not, Realtek's
host driver will refuse the operation to make sure the exlusive accessing
at the same time.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch adds a simple Device Tree binding for the mvsdio driver, as
well as the necessary documentation for it. Compatibility with non-DT
platforms is preserved, by keeping the platform_data based
initialization.
We introduce a small difference between non-DT and DT platforms: DT
platforms are required to provide a clocks = <...> property, which the
driver uses to get the frequency of the clock that goes to the SDIO
IP. The behaviour on non-DT platforms is kept unchanged: a clock
reference is not mandatory, but the clock frequency must be passed in
the "clock" field of the mvsdio_platform_data structure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The MMC core subsystem provides in drivers/mmc/core/slot-gpio.c a nice
set of helper functions to simplify the management of the card detect
GPIO in MMC host drivers. This patch migrates the mvsdio driver to
using those helpers, which will make the ->probe() code simpler, and
therefore ease the process of adding a Device Tree binding for this
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The MMC core subsystem provides in drivers/mmc/core/slot-gpio.c a nice
set of helper functions to simplify the management of the write
protect GPIO in MMC host drivers. This patch migrates the mvsdio
driver to using those helpers, which will make the ->probe() code
simpler, and therefore ease the process of adding a Device Tree
binding for this driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
With commit 9444e07 (mmc: remove unncessary mmc_gpio_free_cd() call from
slot-gpio users) in place, the ESDHC_CD_GPIO handling in IO accessories
becomes unnecessary. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
There are three places where same piece of code is used. Let's split it
to a separate function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
[cjb: The MMP3 architecture requires a registered interrupt to retire wfi
when waking from suspend.]
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Don't disable SD Host IRQ during suspend if it is wake up source.
Enable wakeup event during suspend.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Current code missed disabling interrupts before free irq which is shared.
Notice below comments for function free_irq (kernel/irq/manage.c):
On a shared IRQ the caller must ensure the interrupt is disabled
on the card it drives before calling this function.
Original code has below issue during suspend/resume when multiple SD
hosts share the same IRQ:
1. Assume there are two hosts (host1 for emmc while host2 for sd) share
the same mmc irq.
2. When system suspend, host2 will be suspended before host1.
So the sequence is below:
step1: irq handler for host2 removed ->
step2: irq handler for host1 removed and irq disabled ->
... system suspended ...
... system resumed ...
step3: irq enabled and the irq handler for host1 restored ->
step4: irq handler for host2 restored
3. So there is the buggy time slot that the irq is enabled but the irq
handler for host2 is removed. Then host2 interrupt can be triggered
but can't be handled at that moment.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add a very simple driver for the BCM2835 SoC, which is used in the
Raspberry Pi board.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
