| Age | Commit message (Collapse) | Author |
|---|
|
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Adjust the tmio_mmc block size check to accept 2-byte requests in 4-bit
mode if the hardware supports it.
Tested with the SDHI hardware block included in sh7724.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Magnus Damm <damm@opensource.se>
Tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sh_mmcif controller, so that polling needs
to be used. To overcome the overhead induced by querying the controller
on each poll cycle, card detection can be handled in the platform code
more efficiently.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Some controllers, supported by the tmio_mmc driver do not have the card
detect pin of a slot connected, so that polling needs to be used and
card detection is handled by other means.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: add new sdhci-pxa driver for Marvell SoCs
mmc: make number of mmcblk minors configurable
mmc_spi: Recover from CRC errors for r/w operation over SPI.
mmc: sdhci-pltfm: add -pltfm driver for imx35/51
mmc: sdhci-of-esdhc: factor out common stuff
mmc: sdhci_pltfm: pass more data on custom init call
mmc: sdhci: introduce get_ro private write-protect hook
mmc: sdhci-pltfm: move .h file into appropriate subdir
mmc: sdhci-pltfm: Add structure for host-specific data
mmc: fix cb710 kconfig dependency warning
mmc: cb710: remove debugging printk (info duplicated from mmc-core)
mmc: cb710: clear irq handler on init() error path
mmc: cb710: remove unnecessary msleep()
mmc: cb710: implement get_cd() callback
mmc: cb710: partially demystify clock selection
mmc: add a file to debugfs for changing host clock at runtime
mmc: sdhci: allow for eMMC 74 clock generation by controller
mmc: sdhci: highspeed: check for mmc as well as sd cards
mmc: sdhci: Add Moorestown device support
mmc: sdhci: Intel Medfield support
...
|
|
This adds the support of atmel-mci sd/mmc driver in at91sam9g45 devices and
board files. This also configures the DMA controller slave interface for
at_hdmac dmaengine driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
|
|
Support Marvell PXA168/PXA910/MMP2 SD Host Controller.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The old limit of number of minor numbers per mmcblk device was hardcoded
at 8. This isn't enough for some of the more elaborate partitioning
schemes, for example those used by Chrome OS.
Since there might be a bunch of systems out there with static /dev
contents that relies on the old numbering scheme, let's make it a
build-time option with the default set to the previous 8.
Also provide a boot/modprobe-time parameter to override the config
default: mmcblk.perdev_minors.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Mandeep Baines <msb@chromium.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The SPI bus is not reliable for large data transfers on all platforms.
The current mmc_spi driver fails SD read/write commands immediately if
occasional CRC errors are reported by the SD device. This patch makes
the operation recover from CRC errors by repeating the last SD command.
The retry count is set to 5 to ensure the driver passes stress tests.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This driver adds basic support for the esdhc-core found on e.g.
imx35/51, as a platform driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Put everything which can be shared between the OF and platform version
of this driver into a local .h file.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Eric Bénard <eric@eukrea.com>
[cjb: fix compile error: sdhci-esdhc.c->sdhci-esdhc.h]
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The custom init call may need more data to perform its job, so we pass
it a pointer to pdata, too. Also, always use the platform_id specific
data even if platform_data is present. Doing that, platform_data can
additionally be parsed by init() for board-specific information (via
sdhci->mmc->parent).
(Note: the old behaviour was that you could override the platform_id
specific data with your own. However, one can still do this by using the
"sdhci" id instead of "sdhci-<something>".)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Some controllers handle their write-protection differently. Introduce a
callback to be able to handle it, ensuring the same locking takes place
for it. Rename the status variable to make it more obvious why the read
from the registers needs to be inverted.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Make use of the include/linux/mmc directory.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
We need to carry some information per host, e.g. the clock. Add a
structure for it and initialize it in the generic part. Also improve
the check for a parent.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Fix kconfig dependency warning to satisfy dependencies:
warning: (MMC_CB710 && MMC && PCI) selects CB710_CORE which has
unmet direct dependencies (MISC_DEVICES && PCI)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Clock divider selection in partially verified, so document known facts
in code.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
For debugging power management features it is convenient to have the
possibility of changing the MMC host controller clock at runtime. This
patch adds a 'clock' file for this under the MMC host root of debugfs.
Usage is as follows:
# cat /sys/kernel/debug/mmc0/clock
52000000
# echo "1000000000" > /sys/kernel/debug/mmc0/clock
# cat /sys/kernel/debug/mmc0/clock
52000000
# echo "48000000" > /sys/kernel/debug/mmc0/clock
# cat /sys/kernel/debug/mmc0/clock
48000000
The middle example shows limits being applied by the host driver.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
[cjb: modify changelog language]
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Snippet of code for how adaptation layer should handle the call:
/*
* eMMC spec calls for the host to send 74 clocks to the card
* during initialization, right after voltage stabilization.
* create the clocks manually right here.
*/
void generate_init_clocks_A0(struct sdhci_host *host, u8 power_mode)
{
struct sdhci_mmc_slot *slot = sdhci_priv(host);
if (slot->power_mode == MMC_POWER_UP &&
power_mode == MMC_POWER_ON) {
/* controller specific code here */
/* slot->power_mode holds previous power setting */
}
slot->power_mode = power_mode;
}
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The SD and MMC code set highspeed using different constants.
Change the sd driver to recognize this and switch to high speed.
Validated code when testing eMMC dual data rate.
Signed-off-by: Philip Rakity <prakity@marvell.com>
[cjb: changelog + indentation fixes]
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This adds the basic identifiers. Due to the various chip quirks it's not
enough to make MRST support very useful for earlier steppings but that can
follow.
(I'm currently trying to verify which steps actually matter outside Intel
so I can avoid unneeded stuff going upstream)
[Extracted from original development]
Signed-off-by: JiebingLi <jiebing.li@intel.com>
[Folds in fixes]
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Basic support for the Intel Medfield devices
Give them their own quirks as we will need to update this later.
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Currently we write it to the chip data, but if the probe handler overrides
it we ignore the new value and keep using our cached one. Fix this so that
a probe handler can adjust the slot count.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Bring SDIO devices back to full power before their suspend
handler is invoked.
Doing so ensures that SDIO suspend/resume semantics are
maintained (drivers still get to decide whether their
card should be removed or kept during system suspend,
and at what power state), and that SDIO suspend/resume
execution paths are unchanged.
This is achieved by resuming a runtime-suspended SDIO device
in its ->prepare() PM callback (similary to the PCI subsystem).
Since the PM core always increments the run-time usage
counter before calling the ->prepare() callback and decrements
it after calling the ->complete() callback, it is guaranteed
that when the system will come out of suspend, our device's
power state will reflect its runtime PM usage counter.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
To prevent an erroneous removal of the card, make sure
the device is powered when it is mmc_sdio_detect()ed.
This is required since mmc_sdio_detect may be invoked
while the device is runtime suspended (e.g., MMC core
is rescanning when system comes out of suspend).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Enable runtime PM for SDIO functions.
SDIO functions are initialized with a disabled runtime PM state,
and are set active (and their usage count is incremented)
only before potential drivers are probed.
SDIO function drivers that support runtime PM should call
pm_runtime_put_noidle() in their probe routine, and
pm_runtime_get_noresume() in their remove routine (very
similarly to PCI drivers).
In case a matching driver does not support runtime PM, power will
always be kept high (since the usage count is positive).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Enable runtime PM for new SDIO cards.
As soon as the card will be added to the device tree, runtime PM core
will release its power, since it doesn't have any users yet.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Assign the generic runtime PM handlers for SDIO.
These handlers invoke the relevant SDIO function drivers'
handlers, if exist, otherwise they just return success
(so SDIO drivers don't have to define any runtime PM handlers
unless they need to).
Runtime PM is still disabled by default, so this patch alone
has no immediate effect.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add MMC runtime PM handlers, which call mmc_power_save_host
and mmc_power_restore_host in response to runtime_suspend and
runtime_resume events.
Runtime PM is still disabled by default, so this patch alone
has no immediate effect.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add a power_restore handler to the SDIO bus ops,
in order to support waking up SDIO cards that
were powered off by runtime pm.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Allow power save/restore and their relevant mmc_bus_ops handlers
exit with a return value.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
On resume, let mmc_sdio_init_card go all the way, instead
of skipping the reconfiguration of the card's speed and width.
This is needed to ensure cards wake up with their clock
reconfigured (otherwise it's kept low).
This patch also removes the explicit bus width reconfiguration
on resume, since now this is part of mmc_sdio_init_card.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Some platforms based on sdhci-pltfm need to set their own quirks.
Previously to this patch, the quirks were in drivers/mmc/host/sdhci.h.
This patch splits drivers/mmc/host/sdhci.h into two parts:
* drivers/mmc/host/sdhci.h includes the HC registers and I/O accessors.
* include/linux/mmc/sdhci.h includes the sdhci structure and quirks.
Instead of including drivers/mmc/host/sdhci.h, -pltfm drivers should
now include include/linux/mmc/sdhci.h and include/linux/sdhci-pltfm.h.
This patch avoids adding/changing the calls/flags in the
sdhci_pltfm_data structure. It has been tested on STM platforms
(e.g. STx7106, STx7108, STx5206) where the driver is configured
and used as shown in the example below:
[snip]
static int mmc_pad_resources(struct sdhci_host *sdhci)
{
if (!devm_stm_pad_claim(sdhci->mmc->parent,
&stx7108_mmc_pad_config,
dev_name(sdhci->mmc->parent)))
return -ENODEV;
return 0;
}
static struct sdhci_pltfm_data stx7108_mmc_platform_data = {
.init = mmc_pad_resources,
.quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
};
static struct platform_device stx7108_mmc_device = {
.name = "sdhci",
[snip]
Note: drivers/mmc/host/sdhci.h now also includes linux/mmc/sdhci.h,
and no modifications should be needed on other sdhci-<XXX> drivers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch fixes a warning when compiling the sdhci driver:
pwr may be used uninitialized in sdhci_set_power
Tested with the following compiler versions: 4.2.4 and 4.4.4
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch adds the suspend and resume functions
in the sdhci-pltfm device driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Usually there are multiple mmc host controllers; rename mmc queue thread
by host index so we can easily identify which controller it belongs to.
Signed-off-by: Ethan Du <ethan.too@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
One flaw with DDR support is that MMC core does not inform the driver
which DDR mode it has selected. This patch expands the ios->ddr flag
to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The DDR support patch needs the following fixes:
- The block driver does not need to know about DDR, any more
than it needs to know about bus width.
- Not only the card must be switched to DDR mode. The host
controller must also be configured, which is done through
the 'set_ios()' function.
- Do not set the DDR mode state until after the switch command
is successful.
- Setting block length is not supported in DDR mode. Make that
a core function and change the other place it is used (mmc_test)
also.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add support for Dual Data Rate MMC cards as defined in the 4.4
specification.
Signed-off-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
After discovering a problem in regulator reference counting I took Mark
Brown's advice to move the reference count into the MMC core by making the
regulator status a member of struct mmc_host.
I took this opportunity to also implement NULL versions of
the regulator functions so as to rid the driver code from
some ugly #ifdef CONFIG_REGULATOR clauses.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sundar Iyer <sundar.iyer@stericsson.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Cliff Brake <cbrake@bec-systems.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
mmc_rescan() includes a pr_info which prints 4 lines each second for
hosts configured with MMC_CAP_NEEDS_POLL. This patch enables the message
only if CONFIG_MMC_DEBUG is selected. Tested on i.MX51's sdhci-esdhc.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
In the latest releases of the mmc driver, the freq during initialization
is set to a fixed 400 Khz. This was reportedly too fast for several
users. As there doesn't seem to be an ideal frequency
which-works-for-all, Pierre suggested to let the driver try several
frequencies.
This patch implements that idea. It will try mmc-initialization using
several frequencies from an array 400, 300, 200 and 100.
In case SDIO is broken, it'll still try to detect SDMEM, also at different
freqs.
Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es>
Cc: Pierre Ossman <pierre@ossman.eu>
Reviewed-by: Chris Ball <cjb@laptop.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: Ben Nizette <bn@niasdigital.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When a controller requires SDHCI_QUIRK_BROKEN_CARD_DETECTION, we poll
for card insertion/removal, and that creates interrupts. There's no
need to be doing this if we have a non-removable card.
This patch requires cards to be removable before we're willing to set
MMC_CAP_NEEDS_POLL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
[cjb: modified changelog and code indentation]
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
There are two checks that need to be made when determining whether a
card is removable. A host controller may set MMC_CAP_NONREMOVABLE if the
controller does not support removing cards (e.g. eMMC), in which case
the card is physically non-removable. Also the 'mmc_assume_removable'
module parameter can be configured at module load time, in which case
the card may be logically non-removable.
A helper function keeps the logic in one place so that code always
checks both conditions.
Because this new function is likely to be called from modules we now
need to export the mmc_assume_removable symbol.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The EXTRA_CFLAGS assignment in mmc/Makefile was not accomplishing
anything because this flag only has effect on sources at the same level
as the makefile (i.e., per directory). Since card/, core/, and host/
rely on MMC_DEBUG, the subdir-ccflags-y variant seems to be the
appropriate choice.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
