summaryrefslogtreecommitdiffstats
path: root/drivers/net/dm9000.c
AgeCommit message (Collapse)Author
2008-02-11DM9000: Show the MAC address source after printing MACBen Dooks
Show whether the MAC address was read from the EEPROM or the onboard PAR registers. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Update retry count whilst identifying chipBen Dooks
Reading the ID register does not always return the correct ID from the device, so we retry several times to see if we get a correct value. These failures seem to be excaserbated by the speed of the access to the chip (possibly time between issuing the address and then the data cycle). Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Add support for MII ioctl() callsBen Dooks
Add entry to handle the MII ioctl() calls via the generic_mii_ioctl call. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Add platform flag for no attached EEPROMBen Dooks
Allow the platform data to specify to the DM9000 driver that there is no posibility of an attached EEPROM on the device, so default all reads to 0xff and ignore any write operations. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Remove redudant use of "& 0xff"Ben Dooks
The writing of the data should implicitly truncate the data to 8bits, so do not bother with the ands in the code. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Remove cal_CRC() and use ether_crc_le insteadBen Dooks
Remove the cal_CRC as this is basically wrappering the ether_crc_le function, and is only being used by the multicast hash table functions. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Fix delays used by EEPROM read and writeBen Dooks
The code was using a delay of 8ms, when it should have been using the EEPROM status flag from the device to indicate the EEPROM transaction had finished. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Use netif_msg to enable debugging optionsBen Dooks
Use the netif_msg_*() macros to enable the debugging based on the board's msg_enable field. The output still goes via the dev_dbg() macros, so will be tagged and output as appropriate. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Remove unnecessary changelog in header commentBen Dooks
We have a perfectly good version control system, so we do not need to duplicate change comments in the header for this code. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Ensure spinlock held whilst accessing EEPROM registersBen Dooks
Ensure we hold the spinlock whilst the registers and being modified even though we hold the overall lock. This should protect against an interrupt happening whilst we are using the device. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Remove EEPROM initialisation code.Ben Dooks
Remove the old hack to program an initial EEPROM setting into the DM9000 as we now have ethtool support for reading and writing the EEPROM. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Add ethtool control of msg_enable valueBen Dooks
Allow the msg_enable value to be read and written by the ethtool interface. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Add ethtool support for reading and writing EEPROMBen Dooks
Add ethtool support to access the configuration EEPROM connected to the DM9000. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Add mutex to protect accessBen Dooks
Add a mutex to serialise access to the chip functions from entries such as the ethtool and the MII code. This should reduce the amount of time the spinlock is held to protect the address register. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Remove barely used SROM array read.Ben Dooks
The srom array in the board data is only being used in the device probe routines. The probe also only uses the first 6 bytes of an array we spend 512ms reading 128 bytes from. Change to reading the MAC area directly to the MAC address structure. As a side product, we rename the read_srom_word to dm9000_read_eeprom to bring it into line with the rest of the driver. No change is made to the delay in this function, which will be dealt with in a later patch. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Use msleep() instead of udelay()Ben Dooks
We can use sleeping functions when reading and writing the PHY registers, so let us sleep instead of busy waiting for the PHY. Note, this also fixes a bug reading the PHY where only 100uS was being used instead of 150uS Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Do not sleep with spinlock and IRQs heldBen Dooks
The phy read and write routines call udelay() with the board lock held, and with the posibility of IRQs being disabled. Since these delays can be up to 500usec, and are only required as we have to save the chip's address register. To improve the behaviour, hold the lock whilst we are writing and then restore the state before the delay and then repeat the process once the delay has happened. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Add initial ethtool supportBen Dooks
Add support for ethtool operations for the DM9000. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Remove old timer based poll routinesBen Dooks
Remove the timer based MII phy polling, as this is currently broken with the new EEPROM code that now uses mutexes to protect the phy access. This will need to be replaced in the future by some form of mutex safe mechanism for reading the MII phy status. The replacement has not been done here as changing this patch, which is early in the sequence has quite a knock-on effect. Once this series is merged, then a new presentation of an patch to poll the MII link status can be added. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Pass IRQ flags via platform resourcesBen Dooks
Use the flags in the IRQ resource to specify the type of IRQ being requested, so that systems which do not have level-based interrupts, or change the interrupt in some other way can specify this without making an #ifdef mess in the driver. This is specifically designed to undo the change in commit 4e4fc05a2b6e7bd2e0facd96e0c18dceb34d9349 which hardwires the type for everyone but blackfin to IRQT_RISING, which breaks all a number of Simtec boards which use (and setup in the bootloader) active low IRQs. Note, although there where originally objections due to the use of IORESOURCE_IRQ and IRQT_ flags not sharing the same definition, at least <include/linux/interrupt.h> notes these are the same. Signed-off-by: Ben Dooks <ben-linux@fluff.org> CC: Daniel Mack <daniel@caiaq.de> CC: Bryan Wu <bryan.wu@analog.com> CC: Alex Landau <landau.alex@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000 update debugging macros to use debug levelBen Dooks
Change the debug macros to use the compiler to elide any unnecessary debug level, and to allow device configurable debug control. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000 use dev_xxx() instead of printk for output.Ben Dooks
Move to using dev_dbg() and friends for the output of information to the user. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Add platform data to specify external phyBen Dooks
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com> This patch adds a flag to the DM9000 platform data which, when set, configures the device to use an external PHY. Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com> Signed-off-by: Ben Dooks <ben-linuy@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11DM9000: Fix endian-ness of data accesses.Ben Dooks
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com> This patch splits the receive status in 8bit wide fields and convert the packet length from little endian to CPU byte order. Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28[ARM] 4762/1: Basic support for Toradex Colibri moduleDaniel Mack
This patch adds support for Toradex' PXA27x based Colibri module. It's kept as simple as possible to only provide basic functionality. A default config is also included. Signed-off-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-10-19DM9000 initialization fixMike Rapoport
DM9000 driver returns success even if it is failed to detect the chip. Below patch fixes it. Signed-off-by: Mike Rapoport <mike@compulab.co.il> drivers/net/dm9000.c | 6 +++--- 1 files changed, 3 insertions(+), 3 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10[NET]: Introduce and use print_mac() and DECLARE_MAC_BUF()Joe Perches
This is nicer than the MAC_FMT stuff. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10[NET] drivers/net: statistics cleanup #1 -- save memory and shrink codeJeff Garzik
We now have struct net_device_stats embedded in struct net_device, and the default ->get_stats() hook does the obvious thing for us. Run through drivers/net/* and remove the driver-local storage of statistics, and driver-local ->get_stats() hook where applicable. This was just the low-hanging fruit in drivers/net; plenty more drivers remain to be updated. [ Resolved conflicts with napi_struct changes and fix sunqe build regression... -DaveM ] Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10[NET]: Nuke SET_MODULE_OWNER macro.Ralf Baechle
It's been a useless no-op for long enough in 2.6 so I figured it's time to remove it. The number of people that could object because they're maintaining unified 2.4 and 2.6 drivers is probably rather small. [ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ] Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-08-25DM9000: fix interface hang under loadFlorian Westphal
When transferring data at full speed, the DM9000 network interface sometimes stops sending/receiving data. Worse, ksoftirqd consumes 100% cpu and the net tx watchdog never triggers. Fix by spin_lock_irqsave() in dm9000_start_xmit() to prevent the interrupt handler from interfering. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-12Blackfin arch: Port the dm9000 driver to Blackfin by using the correct ↵Alex Landau
low-level io routines Signed-off-by: Alex Landau <landau.alex@gmail.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com>
2007-05-08drivers/net/dm9000: Convert to generic booleanRichard Knutsson
Convert to generic boolean. Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-08DM9000: fix use of kfree() on net deviceBen Dooks
The DM9000 network driver is calling kfree() on an netdev causing the system to oops if the probe fails. The right thing to do is call free_netdev(). Thanks to Russell King for spotting this. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-25[ETH]: Make eth_type_trans set skb->dev like the other *_type_transArnaldo Carvalho de Melo
One less thing for drivers writers to worry about. Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2006-10-08[PATCH] misc arm pt_regs fixesAl Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-05IRQ: Maintain regs pointer globally rather than passing to IRQ handlersDavid Howells
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-09-11[PATCH] Fix dm9000 release_resourceDirk Opfer
dm9000_release_board calls release_resource with the platform resource instead of the requested resource: db->addr_res = platform_get_resource(pdev, IORESOURCE_MEM, 0); db->addr_req = request_mem_region(db->addr_res->start, i, pdev->name); dm9000_release_board: if (db->addr_res != NULL) { release_resource(db->addr_res); kfree(db->addr_req); With this behavior the kernel will crash on the second removal. The attached patch fix this problem. Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-19[PATCH] net: Add netconsole support to dm9000 driverKevin Hao
Add netconsole support to dm9000 driver. Cc: Jeff Garzik <jeff@garzik.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-02[PATCH] irq-flags: drivers/net: Use the new IRQF_ constantsThomas Gleixner
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: "David S. Miller" <davem@davemloft.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26[PATCH] DM9000 - minor code cleanupsBen Dooks
Ensure the driver's module owner field is initialised for when this is being built and loaded as a module. Also change make the dm9000_tx_done function static, as it is not exported elsewhere. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-26[PATCH] DM9000 - do no re-init spin lockBen Dooks
The DM9000 initialisation sequence for the hardware re-initialise the board spin-lock, which is in my view wrong. This patch removes the extra spin lock initialisation Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-26[PATCH] DM9000 - check for MAC left in by bootloaderBen Dooks
The DM9000 driver does not deal with the case where there is no serial EEPROM to store the configuration, and the bootloader has placed an MAC address into the device already. If there is no valid MAC in the EEPROM, read the one already in the chip and check to see if that one is valid. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-26[PATCH] DM9000 - better checks for platform resourcesBen Dooks
The current DM9000 driver cannot cope if it is given more than 3 resources (for example, if it is being passed an wake-up irq that it is not using yet). Check that we have been given at-least one IRQ resource. Also fix the minor type-casting for the case of 2 resources. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2005-11-11Merge master.kernel.org:/home/rmk/linux-2.6-drvmodelLinus Torvalds
2005-11-09[DRIVER MODEL] Convert platform drivers to use struct platform_driverRussell King
This allows us to eliminate the casts in the drivers, and eventually remove the use of the device_driver function pointer methods for platform device drivers. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-11-09[PATCH] changing CONFIG_LOCALVERSION rebuilds too much, for no good reasonOlaf Hering
This patch removes almost all inclusions of linux/version.h. The 3 #defines are unused in most of the touched files. A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is unfortunatly in linux/version.h. There are also lots of #ifdef for long obsolete kernels, this was not touched. In a few places, the linux/version.h include was move to where the LINUX_VERSION_CODE was used. quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'` search pattern: /UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h Signed-off-by: Olaf Hering <olh@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-10-29Create platform_device.h to contain all the platform device details.Russell King
Convert everyone who uses platform_bus_type to include linux/platform_device.h. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-10-28[PATCH] DRIVER MODEL: Get rid of the obsolete tri-level suspend/resume callbacksRussell King
In PM v1, all devices were called at SUSPEND_DISABLE level. Then all devices were called at SUSPEND_SAVE_STATE level, and finally SUSPEND_POWER_DOWN level. However, with PM v2, to maintain compatibility for platform devices, I arranged for the PM v2 suspend/resume callbacks to call the old PM v1 suspend/resume callbacks three times with each level in order so that existing drivers continued to work. Since this is obsolete infrastructure which is no longer necessary, we can remove it. Here's an (untested) patch to do exactly that. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-06[PATCH] missed s/u32/pm_message_t/ (dm9000)viro@ftp.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-08-18[PATCH] DM9000 - incorrect ioctl() handlingBen Dooks
The DM9000 driver is responding to ioctl() calls it should not be. This can cause problems with the wireless tools incorrectly indentifying the device as wireless capable, and crashing under certain operations. This patch also moves the version printk() to the init call, so that you only get it once for multiple devices, and to show it is loaded if there are no defined dm9000s Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>