summaryrefslogtreecommitdiffstats
path: root/drivers/net/e1000e/e1000.h
AgeCommit message (Collapse)Author
2011-08-10intel: Move the Intel wired LAN driversJeff Kirsher
Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and the necessary Kconfig and Makefile changes. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-07-12e1000e: use GFP_KERNEL allocations at init timeJeff Kirsher
In process and sleep allowed context, favor GFP_KERNEL allocations over GFP_ATOMIC ones. -v2: fixed checkpatch.pl warnings CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Ben Greear <greearb@candelatech.com> CC: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-11e1000e: remove e1000_queue_statsEric Dumazet
struct e1000_queue_stats is not used, lets remove it Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-06-09e1000e: Clear host wakeup bit on 82577/8 without touching PHY page 800Bruce Allan
The Host Wakeup Active bit in the PHY Port General Configuration register (page 769 register 17) must be cleared after every PHY reset to prevent an unexpected wake signal from the PHY. Originally, this was accomplished by simply reading the PHY Wakeup Control register on page 800 which clears the Host Wakeup Active bit as a side-effect. Unfortunately, a hardware bug on the 82577 and 82578 PHY can cause unexpected behavior when registers on page 800 are accessed while in gigabit mode. This patch changes the remaining instances when the Host Wakeup Active bit needs to be cleared while possibly in gigabit mode by accessing the Port General Configuration register directly instead of accessing any register on page 800. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-06-09e1000e: access multiple PHY registers on same page at the same timeBruce Allan
Doing a PHY page select can take a long time, relatively speaking. This can cause a significant delay when updating a number of PHY registers on the same page by unnecessarily setting the page for each PHY access. For example when going to Sx, all the PHY wakeup registers (WUC, RAR[], MTA[], SHRAR[], IP4AT[], IP6AT[], etc.) on 82577/8/9 need to be updated which takes a long time which can cause issues when suspending. This patch introduces new PHY ops function pointers to allow callers to set the page directly and do any number of PHY accesses on that page. This feature is currently only implemented for 82577, 82578 and 82579 PHYs for both the normally addressed registers as well as the special- case addressing of the PHY wakeup registers on page 800. For the latter registers, the existing function for accessing the wakeup registers has been divided up into three- 1) enable access to the wakeup register page, 2) perform the register access and 3) disable access to the wakeup register page. The two functions that enable/disable access to the wakeup register page are necessarily available to the caller so that the caller can restore the value of the Port Control (a.k.a. Wakeup Enable) register after the wakeup register accesses are done. All instances of writing to multiple PHY registers on the same page are updated to use this new method and to acquire any PHY locking mechanism before setting the page and performing the register accesses, and release the locking mechanism afterward. Some affiliated magic number cleanup is done as well. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-06-09e1000e: 82579 intermittently disabled during S0->SxBruce Allan
When repeatedly cycling Sx->S0 states with the network cable unplugged, the 82579 PHY may not initialize as expected and may require a full power cycle to recover functionality to the device. Workaround this by testing access of the PHY registers after resuming; if that returns unexpected results toggle the LANPHYPC signal to power cycle the PHY. This is implemented in the new function e1000_resume_workarounds_pchlan() which calls another new function, e1000_toggle_lanphypc_value_ich8lan(), which has been created to reduce code duplication (same functionality required by a previous workaround). Also, e1000e_disable_gig_wol_ich8lan is now e1000_suspend_workarounds_ich8lan to better reflect what it does. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-04-27e1000e: implement ethtool set_phys_idBruce Allan
Based on a patch from Stephen Hemminger <shemminger@vyatta.com>. The new ethtool set_phys_id takes over controlling the LED for identifying boards. This fixes the lockout during that period. For this device lots of extra infrastructure can also be removed by using set_phys_id. v2: - return blink frequency for parts that do not support blink in h/w - add blink_led function pointers for devices that do support blink in h/w to cleanup the test for this functionality Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Cc: Stephen Hemminger <shemminger@vyatta.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-04-13e1000e: If ASPM L0s needs to be disabled, do it prior to enabling deviceBruce Allan
Based on a patch from Naga Chumbalkar <nagananda.chumbalkar@hp.com>: If ASPM L0s needs to be disabled due to HW errata, do it prior to "enabling" the device. This way if the kernel ever defaults its aspm_policy to POLICY_POWERSAVE, then the e1000e driver will get a chance to disable ASPM on the misbehaving device *prior* to calling pci_enable_device_mem(). This will be useful in situations where the BIOS indicates ASPM support on the server by clearing the ACPI FADT "ASPM Controls" bit. Note: The kernel (2.6.38) currently uses the BIOS "default" as its aspm_policy. However, Linux distros can diverge from that and set the default to "powersave". v2: o cleanup namespace pollution of e1000e_disable_aspm(), o fix type and initialization of the new aspm_disable_flag in a few functions, and o redefine FLAG2_DISABLE_ASPM_L0S to the first unused bit in adapter->flags2. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-04-13e1000e: convert to new VLAN modelJeff Kirsher
This switches the e1000e driver to use the new VLAN interfaces. CC: Jesse Gross <jesse@nicira.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
2011-01-24e1000e: convert to stats64Jeff Kirsher
Based on the patch provided by Flavio Leitner <fleitner@redhat.com> Provides accurate stats at the time user reads them. v2: fixed whitespace/merging issues (by Jeff Kirsher) v3: fixed namespacing issues (by Bruce Allan) CC: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Flavio Leitner <fleitner@redhat.com>
2011-01-14e1000e: update Copyright for 2011Bruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-01-09e1000e: power off PHY after reset when interface is downBruce Allan
Some Phys supported by the driver do not remain powered off across a reset of the device when the interface is down, e.g. on 82571, but not on 82574. This patch powers down (only when WoL is disabled) the PHY after a reset if the interface is down and the ethtool diagnostics are not currently running. The ethtool diagnostic function required a minor re-factor as a result, and the e1000_[get|put]_hw_control() functions are renamed since they are no longer static to netdev.c as they are needed by the ethtool diagnostics. A couple minor whitespace issues were cleaned up, too. Reported-by: Arthur Jones <ajones@riverbed.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-01-09e1000e: use either_crc_le() rather than re-write itBruce Allan
For the 82579 jumbo frame workaround, there is no need to re-write the CRC calculation functionality already found in the kernel's ether_crc_le(). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-10e1000e: support new PBA format from EEPROMBruce Allan
Provide support to e1000e for displaying the new format of the PBA found in the EEPROM. The unique PBA identifier is no longer restricted to hexadecimal numbers and must now be read and displayed as a string. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-12-10e1000e: fix double initialization in blink pathHolger Eitzenberger
The kernel goes BUG() at the time 'ethtool -p eth0 3' comes back, which is due to adapter->led_blink_task initialized several times. At the time it is still running this results in a corrupted task_list of the associated workqueue. The fix is to move the workqueue initialization to the probe function instead. Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2010-10-28e1000e: reset PHY after errors detectedCarolyn Wyborny
Some errors can be induced in the PHY via environmental testing (specifically extreme temperature changes and electro static discharge testing), and in the case of the PHY hanging due to this input, this detects the problem and resets to continue. This issue only applies to 82574 silicon. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-30e1000e: 82579 performance improvementsBruce Allan
The initial support for 82579 was tuned poorly for performance. Adjust the packet buffer allocation appropriately for both standard and jumbo frames; and for jumbo frames increase the receive descriptor pre-fetch, disable adaptive interrupt moderation and set the DMA latency tolerance. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-30e1000e: use hardware writeback batchingJesse Brandeburg
Most e1000e parts support batching writebacks. The problem with this is that when some of the TADV or TIDV timers are not set, Tx can sit forever. This is solved in this patch with write flushes using the Flush Partial Descriptors (FPD) bit in TIDV and RDTR. This improves bus utilization and removes partial writes on e1000e, particularly from 82571 parts in S5500 chipset based machines. Only ES2LAN and 82571/2 parts are included in this optimization, to reduce testing load. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-02e1000e: Fix irq_synchronize in MSI-X caseJeff Kirsher
Based on original patch/work from Jean Delvare <jdelvare@suse.de> Synchronize all IRQs when in MSI-X IRQ mode. Jean's original patch hard coded the sync with the 3 possible vectors, this patch incorporates more flexibility for the future and aligns with how igb stores the number of vectors into the adapter structure. CC: Jean Delvare <jdelvare@suse.de> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23e1000e: avoid polling h/w registers during link negotiationBruce Allan
Avoid touching hardware registers when possible, otherwise link negotiation can get messed up when user-level scripts are rapidly polling the driver to see if/when link is up. Use the saved link state information instead when possible. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: update copyright informationBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: enable support for EEE on 82579Bruce Allan
This patch enables IEEE802.3az (a.k.a. Energy Efficient Ethernet) on the new 82579 LOMs. An optional module parameter is provided to disable the feature if desired. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: initial support for 82579 LOMsBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: separate out PHY statistics register updatesBruce Allan
The 82577/82578 parts have half-duplex statistics in PHY registers. These need only be read when in half-duplex and should all be read at once rather than one at a time to prevent excessive cycles of acquiring/releasing the PHY semaphore. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05e1000e: save skb counts in TX to avoid cache missesTom Herbert
In e1000_tx_map, precompute number of segements and bytecounts which are derived from fields in skb; these are stored in buffer_info. When cleaning tx in e1000_clean_tx_irq use the values in the associated buffer_info for statistics counting, this eliminates cache misses on skb fields. Signed-off-by: Tom Herbert <therbert@google.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-27Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/e100.c drivers/net/e1000e/netdev.c
2010-04-27e1000e: enable/disable ASPM L0s and L1 and ERT according to hardware errataBruce Allan
Prompted by a previous patch submitted by Matthew Garret <mjg@redhat.com>, further digging into errata documentation reveals the current enabling or disabling of ASPM L0s and L1 states for certain parts supported by this driver are incorrect. 82571 and 82572 should always disable L1. For standard frames, 82573/82574/82583 can enable L1 but L0s must be disabled, and for jumbo frames 82573/82574 must disable L1. This allows for some parts to enable L1 in certain configurations leading to better power savings. Also according to the same errata, Early Receive (ERT) should be disabled on 82573 when using jumbo frames. Cc: Matthew Garret <mjg@redhat.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-06Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/bonding/bond_main.c drivers/net/via-velocity.c drivers/net/wireless/iwlwifi/iwl-agn.c
2010-03-26e1000e: Use pr_<level> and netdev_<level>Bruce Allan
As an alternative to a quite large patch previously submitted by Joe Perches to make use of kernel logging API, this patch is much less intrusive. Convert e_<level> to netdev_<level> Use #define pr_fmt Convert a few printks to pr_<level> Cc: Joe Perches <joe@perches.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-26e1000e: do not modify tx_queue_len on link speed changeEmil Tantilov
Previously the driver tweaked txqueuelen to avoid false Tx hang reports seen at half duplex. This had the effect of overriding user set values on link change/reset. Testing shows that adjusting only the timeout factor is sufficient to prevent Tx hang reports at half duplex. This patch removes all instances of tx_queue_len in the driver. Originally reported and patched by Franco Fichtner CC: Franco Fichtner <franco@lastsummer.de> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-16e1000e / PCI / PM: Add basic runtime PM support (rev. 4)Rafael J. Wysocki
Use the PCI runtime power management framework to add basic PCI runtime PM support to the e1000e driver. Namely, make the driver suspend the device when the link is off and set it up for generating a wakeup event after the link has been detected again. [This feature is disabled until the user space enables it with the help of the /sys/devices/.../power/contol device attribute.] Based on a patch from Matthew Garrett. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-04e1000e: Fix namespace conflicts wrt. e1000_has_linkDavid S. Miller
Reported by Stephen Rothwell. Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-23Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
2010-01-20e1000e: enhance frame fragment detectionJesse Brandeburg
Originally patched by Neil Horman <nhorman@tuxdriver.com> e1000e could with a jumbo frame enabled interface, and packet split disabled, receive a packet that would overflow a single rx buffer. While in practice very hard to craft a packet that could abuse this, it is possible. this is related to CVE-2009-4538 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13e1000e: genericize the update multicast address listBruce Allan
Make updating the multicast address list generic for all families and enforce the requirement to update the entire multicast table array all at once instead of piecemeal which causes problems on some parts. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13e1000e: provide MAC-family-specific function to set LAN IDBruce Allan
Provide MAC-specific function pointer to determine the LAN ID (PCI func). The LAN ID is used internally by the driver to determine which h/w lock to use to protect accessing the PHY on ESB2 as well as help to determine the alternate MAC address on some parts. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13e1000e: use alternate MAC address on ESB2 if availableBruce Allan
Similar to 82571/2/3 parts that already do this, if ESB2/80003es2lan parts have an alternate MAC address provided in the EEPROM use it instead of the default MAC address. This patch makes the the actual code that does this generic so that it can be better used by both MAC families. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-13e1000e: MDIO slow mode should always be done for 82577Bruce Allan
A previous 82577 workaround that set the MDIO access speed to slow mode for every PHY register read/write when the cable is unplugged should instead set the access mode to always be slow before any PHY register access. Since the mode bit gets cleared when the PHY is reset, set the mode after every PHY reset. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: correct ICH/PCH PHY operations function pointersBruce Allan
Some function pointers for a few PHY operations (for 82578 and 82567) and were set incorrectly causing functions to be executed that were accessing incorrect PHY register offsets for that particular device. This patch also moves a few PHY-specific functions from ich8lan.c to the more appropriate phy.c. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: remove use of skb_dma_map from e1000e driverAlexander Duyck
In testing we have found that skb_dma_map/unmap is incompatible with HW IOMMU due to the fact that multiple mappings will return different results. In order to correct this we need to remove skb_dma_map/unmap calls from the e1000e driver. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: provide family-specific PHY power up/down operationsBruce Allan
The different families (80003es2lan, 8257x, ICHx/PCH) supported by the driver each have their own conditions when the PHY can be powered down. This patch rewrites the PHY power up/down code to fit with the family- specific style used in the driver. All pre-existing calls to power up or down the PHY remain untouched. A new call to power down the PHY when removing the driver when the interface is down replaces the current call to reset the PHY in order to reduce power consumption. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: provide family-specific functions to manage VLAN filter arraysBruce Allan
The two MAC-families that have VLAN filter table register arrays manage each a bit differently from one another, so provide family-specific functions for managing the register arrays and function pointers to access the appropriate function. Also make sure attempts to access these register arrays are not done on parts not supporting that feature. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-29Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/ieee802154/fakehard.c drivers/net/e1000e/ich8lan.c drivers/net/e1000e/phy.c drivers/net/netxen/netxen_nic_init.c drivers/net/wireless/ath/ath9k/main.c
2009-11-21e1000e: update Tx Unit hang detection messageBruce Allan
The Tx unit hang detection code in e1000e detects other hangs caused by hardware components (e.g. Rx, DMA units), but it is not possible to detect exactly which component is hung so it has always assumed a Tx unit hang. When dumping a message to the system log because of a hang, this patch adds more data to help narrow the cause of the issue and makes the message non-Tx-specific. Because this new code reads PHY registers which can sleep, move it off to a workqueue. This and all previously existing work tasks in the driver are now cancelled when the driver is removed. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: update copyright informationBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: cleanup ops function pointersBruce Allan
The phy and nvm operations structures have function pointers that contain "phy" and "nvm" in the pointer names which are redundant since the structures are already obviously in phy and nvm structures. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: consolidate two dbug macros into one simpler oneBruce Allan
This patch depends on a previous one that cleans up redundant #includes. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: cleanup redundant #include'sBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: disable K1 on PCH LOM when in PHY loopback modeBruce Allan
When performing the ethtool PHY loopback test on PCH-based LOMs (82577 and 82578), disable K1 (a MAC-PHY interconnect low power mode) otherwise packets might get corrupted. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20e1000e: partial revert of 3ec2a2b8 plus FC workraround for 82577/8Bruce Allan
Commit 3ec2a2b80f3eb53851fe4cef9e65b5d33376ef89 broke Tx/Rx when using jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged once the high water mark was reached preventing normal packet traffic). This patch reverts the breakage and sets appropriate high and low water marks of the Rx FIFO for 82577/82578 which require a workaround due to a flow control issue in hardware. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-25 00:05:43 +0000