| Age | Commit message (Collapse) | Author |
|---|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
|
|
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
i) Fixes a bug where e1000_sw_lcd_config_ich8lan() was calling
e1000_lan_init_done_ich8lan() to poll the STATUS.LAN_INIT_DONE bit to
make sure the MAC had completed the PHY configuration. However,
e1000_lan_init_done_ich8lan() had already been called in one of the two
places where PHY reset occurs for ICHx/PCHx parts, which caused the second
call to busy-wait for 150 msec because the LAN_INIT_DONE bit had already
been checked and cleared.
ii) Cleanup the two separate PHY reset code paths, i.e. the full-chip reset
in e1000_reset_hw_ich8lan() and the PHY-only reset in
e1000_phy_hw_reset_ich8lan(). There was duplicate code in both paths to be
performed post-reset that are now combined into one new function -
e1000_post_phy_reset_ich8lan(). This cleanup also included moving the
clearing of the PHY Reset Asserted bit in the STATUS register (now done for
all ICH/PCH parts) and the check for the indication from h/w that basic
configuration has completed back to where it previously was in
e1000_get_cfg_done_ich8lan().
iii) Corrected a few comments
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flow control refresh timer value needs to be saved off so that it can
be programmed into the approrpiate register when applicable but without a
reset, e.g. when changing flow control parameters via ethtool.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mac->arc_subsystem was being incorrectly used to flag whether or not
manageability was enabled when it should only be used to state whether the
ARC (Host interface) subsystem is available on a particular MAC _and_ only
valid when any manageability is enabled. The ARC subsystem is currently
only available on 80003es2lan and 82573 parts supported by the driver.
A new flag, has_fwsm, is introduced to be used when checking if
manageability is enabled but only on parts that acutally have an FWSM
register. While the above parts have an FWSM register, there are other
parts that have FWSM but do not have support for the ARC subsystem,
namely 82571/2 and ICHx/PCH.
And then there are parts that have manageability, but do not have either
FWSM register or support for the ARC subsystem - these are 82574 and 82583.
For 80003es2lan, 82571/2/3 and ICH/PCH parts, this patch makes no
functional changes, it only corrects the usage of the manageability flags.
For 82574 and 82583, it fixes the incorrect accesses of the non-existent
FWSM register and ARC subsystem as well as corrects the check for
management pass-through.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The force_speed_duplex function pointer was incorrectly set. Instead of
calling the 82577-specific version it was calling the m88 version which,
among other incorrect things, reset the PHY causing autonegotiation to be
re-enabled in the PHY resulting in the link defaulting to half-duplex.
The 82577-specific force_speed_duplex function also had an issue where
it disabled Auto-MDI-X which caused the link to not come up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After every reset all ICH/PCH parts call this function which acquires the
swflag, performs a workaround on applicable parts and releases the swflag.
There is no reason for parts for which this workaround is not applicable
to acquire and release the swflag so the function should just return
without doing anything for these parts. This also provides for the
indentation of most of the function contents to be shifted left cleaning up
the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch addresses issues when manageability passthrough is enabled, but the
MAC_ADDR_FILTER bit is not set in the MANC register.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
...in e1000_update_nvm_checksum_ich8lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In MSI-X mode when an IMPI SoL session was active (i.e. the PHY reset was
blocked), the LSC interrupt generated by s/w to start the watchdog which
started the transmitter was not getting fired by the hardware because bit
24 (the 'other' cause bit) also needed to be set. Without an active SoL
session, the PHY was reset which caused the h/w to fire the LSC interrupt.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82574/82583 uses different registers/bits to setup manageability filters
than all other parts supported by e1000e; set them accordingly for IPMI
pass-through. Rename the function to better reflect what it does.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running ethtool online diagnostics with no open interface, there is a
short period of time where the driver relinquishes control of the adapter
during which time AMT (manageability firmware) can put the adapter into an
unknown state resulting in such things as link test failure, hardware hang,
reporting an incorrect link speed, etc. Resetting the adapter during an
open() resolves this by putting the adapter into a quiescent state.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A couple stack cleanups missed in an earlier patch from Jesse.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the string based list management to a handle base
implementation to help with the hot path use of pm-qos, it also renames
much of the API to use "request" as opposed to "requirement" that was
used in the initial implementation. I did this because request more
accurately represents what it actually does.
Also, I added a string based ABI for users wanting to use a string
interface. So if the user writes 0xDDDDDDDD formatted hex it will be
accepted by the interface. (someone asked me for it and I don't think
it hurts anything.)
This patch updates some documentation input I got from Randy.
Signed-off-by: markgross <mgross@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Reset the PHY before first accessing it. Doing so, ensure that the PHY is
in a known good state before we read/write PHY registers. This fixes a
driver probe failure.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During Sx->S0 transitions, the interconnect between the MAC and PHY on
82577/82578 can remain in SMBus mode instead of transitioning to the
PCIe-like mode required during normal operation. Toggling the LANPHYPC
Value bit essentially resets the interconnect forcing it to the correct
mode.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Back before e1000-7.3.20, the e1000 driver had a simple algorithm that
managed interrupt moderation. The driver was updated in 7.3.20 to
have the new "adaptive" interrupt moderation but we have customer
requests to redeploy the old way as an option. This patch adds the
old functionality back. The new functionality can be enabled via
module parameter or at runtime via ethtool.
Module parameter: (InterruptThrottleRate=4) to use this new
moderation method.
Ethtool method: ethtool -C ethX rx-usecs 4
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change increases the RX fifo size to 36K for standard frames and
decreases the TX fifo size to 4K. The reason for this change is that on
slower systems the RX is much more likely to backfill and need space than
the TX is. As long as the TX fifo is twice the size of the MTU we should
have more than enough TX fifo.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set net->devirq to pdev->irq. This should be consistent with other
drivers.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove e_info message printed whenever TSO is enabled or disabled.
This is not very useful and just clutters dmesg.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reduce number of writes to RX producer pointer. When alloc'ing RX
buffers, only write the RX producer pointer once every
E1000_RX_BUFFER_WRITE (16) buffers created.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In e1000_tx_map, precompute number of segements and bytecounts which
are derived from fields in skb; these are stored in buffer_info. When
cleaning tx in e1000_clean_tx_irq use the values in the associated
buffer_info for statistics counting, this eliminates cache misses
on skb fields.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
Commit 6f461f6c7c961f0b1b73c0f27becf472a0ac606b
("e1000e: enable/disable ASPM L0s and L1 and ERT according to hardware errata")
oopses on one of my ppc64 boxes with a NULL pointer (0x4a):
Unable to handle kernel paging request for data at address 0x0000004a
Faulting instruction address: 0xc0000000004d2f1c
cpu 0xe: Vector: 300 (Data Access) at [c000000bec1833a0]
pc: c0000000004d2f1c: .e1000e_disable_aspm+0xe0/0x150
lr: c0000000004d2f0c: .e1000e_disable_aspm+0xd0/0x150
dar: 4a
[c000000bec1836d0] c00000000069b9d8 .e1000_probe+0x84/0xe8c
[c000000bec1837b0] c000000000386d90 .local_pci_probe+0x4c/0x68
[c000000bec183840] c0000000003872ac .pci_device_probe+0xfc/0x148
[c000000bec183900] c000000000409e8c .driver_probe_device+0xe4/0x1d0
[c000000bec1839a0] c00000000040a024 .__driver_attach+0xac/0xf4
[c000000bec183a40] c000000000409124 .bus_for_each_dev+0x9c/0x10c
[c000000bec183b00] c000000000409c1c .driver_attach+0x40/0x60
[c000000bec183b90] c0000000004085dc .bus_add_driver+0x150/0x328
[c000000bec183c40] c00000000040a58c .driver_register+0x100/0x1c4
[c000000bec183cf0] c00000000038764c .__pci_register_driver+0x78/0x128
Seems like pdev->bus->self == NULL. I haven't touched pci in a long time
so I'm trying to remember what this means (no pcie bridge perhaps?)
The patch below fixes the oops for me.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds registers (,tx/rx rings' status and so on) printout
code just before resetting adapters. This will be helpful for detecting
the root cause of adapters reset.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/e100.c
drivers/net/e1000e/netdev.c
|
|
Prompted by a previous patch submitted by Matthew Garret <mjg@redhat.com>,
further digging into errata documentation reveals the current enabling or
disabling of ASPM L0s and L1 states for certain parts supported by this
driver are incorrect. 82571 and 82572 should always disable L1. For
standard frames, 82573/82574/82583 can enable L1 but L0s must be disabled,
and for jumbo frames 82573/82574 must disable L1. This allows for some
parts to enable L1 in certain configurations leading to better power
savings.
Also according to the same errata, Early Receive (ERT) should be disabled
on 82573 when using jumbo frames.
Cc: Matthew Garret <mjg@redhat.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
replaces (skb->len - skb->data_len) occurrences by skb_headlen(skb)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/pcmcia/smc91c92_cs.c
drivers/net/virtio_net.c
|
|
Tx ring buffers after tx_ring->next_to_use are volatile and could
change, possibly causing a crash. Stop cleaning when we hit
tx_ring->next_to_use.
Signed-off-by: Terry Loftin <terry.loftin@hp.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
used a modified checkstack to get the 56 number
(normally checkstack wouldn't show this low a value)
checkstack before:
0x0000012f e1000e_check_options [e1000e]: 272
after:
0x0000012f e1000e_check_options [e1000e]: 56
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/stmmac/stmmac_main.c
drivers/net/wireless/wl12xx/wl1271_cmd.c
drivers/net/wireless/wl12xx/wl1271_main.c
drivers/net/wireless/wl12xx/wl1271_spi.c
net/core/ethtool.c
net/mac80211/scan.c
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/via-velocity.c
drivers/net/wireless/iwlwifi/iwl-agn.c
|
|
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here are the other miscellaneous corrections
done by an earlier larger suggested patch now
made unnecessary by a less invasive change.
Correct a few missing newlines from logging
messages and a typo fix. Fix speed/duplex
logging message.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
As an alternative to a quite large patch previously submitted by Joe
Perches to make use of kernel logging API, this patch is much less
intrusive.
Convert e_<level> to netdev_<level>
Use #define pr_fmt
Convert a few printks to pr_<level>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously the driver tweaked txqueuelen to avoid false Tx hang reports seen at half duplex.
This had the effect of overriding user set values on link change/reset. Testing shows that
adjusting only the timeout factor is sufficient to prevent Tx hang reports at half duplex.
This patch removes all instances of tx_queue_len in the driver.
Originally reported and patched by Franco Fichtner
CC: Franco Fichtner <franco@lastsummer.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent PCI runtime PM patch broke build for CONFIG_PM_RUNTIME
and CONFIG_PM_SLEEP undefined. Fix that by moving the PM callbacks
under suitable #ifdefs.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the PCI runtime power management framework to add basic PCI
runtime PM support to the e1000e driver. Namely, make the driver
suspend the device when the link is off and set it up for generating
a wakeup event after the link has been detected again. [This
feature is disabled until the user space enables it with the help of
the /sys/devices/.../power/contol device attribute.]
Based on a patch from Matthew Garrett.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (108 commits)
bridge: ensure to unlock in error path in br_multicast_query().
drivers/net/tulip/eeprom.c: fix bogus "(null)" in tulip init messages
sky2: Avoid rtnl_unlock without rtnl_lock
ipv6: Send netlink notification when DAD fails
drivers/net/tg3.c: change the field used with the TG3_FLAG_10_100_ONLY constant
ipconfig: Handle devices which take some time to come up.
mac80211: Fix memory leak in ieee80211_if_write()
mac80211: Fix (dynamic) power save entry
ipw2200: use kmalloc for large local variables
ath5k: read eeprom IQ calibration values correctly for G mode
ath5k: fix I/Q calibration (for real)
ath5k: fix TSF reset
ath5k: use fixed antenna for tx descriptors
libipw: split ieee->networks into small pieces
mac80211: Fix sta_mtx unlocking on insert STA failure path
rt2x00: remove KSEG1ADDR define from rt2x00soc.h
net: add ColdFire support to the smc91x driver
asix: fix setting mac address for AX88772
ipv6 ip6_tunnel: eliminate unused recursion field from ip6_tnl{}.
net: Fix dev_mc_add()
...
|
|
Conflicts:
Documentation/filesystems/proc.txt
arch/arm/mach-u300/include/mach/debug-macro.S
drivers/net/qlge/qlge_ethtool.c
drivers/net/qlge/qlge_main.c
drivers/net/typhoon.c
|
|
when receiving a particular type of NFS v2 UDP traffic, the hardware could
DMA some bad data and then hang, possibly corrupting memory.
Disable the NFS parsing in this hardware, verified to fix the bug.
Originally reported and reproduced by RedHat's Neil Horman
CC: nhorman@tuxdriver.com
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
