| Age | Commit message (Collapse) | Author |
|---|
|
Driver and Firmware versions updated to 3.2.21.1.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change Details:
- Added Stats clear counter to the bfi_enet_stats_mac structure and
ethtool stats
- Modified the firmware naming convention to contain the firmware image
version (3.1.0.0). The new convention is
<firmware-image>-<firmware-version>.bin The change will enforce loading
only compatible firmware with this driver and also avoid over-writing
the old firmware image in-order to load new version driver as the
firmware names used to be the same.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reduce the number of #defines, use the normal #define from if_ether.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new device ID 0x22 and new asic generation BFI_ASIC_GEN_CT2 for 1860.
Implement FW download from user space for new Brocade HW.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change details:
- Print log messages when running with reduced number of MSI-X vectors
and when defaulting to INTx mode.
- Remove BUG_ONs and header file inclusion that are not needed
- Comments addition/cleanup
- Unused code cleanup
- Add New Line to Print msg in bfa_sm_fault
- Formatting fix
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change details:
This patch contains additional structure and function definition changes
that are required to enable the new msgq/enet/txrx redesign introduced
by the previous 4 patches.
- structure and function definition changes to header files as a result
of Ethport, Enet, IOCEth, Tx, Rx redesign.
- ethtool changes to use new enet function and definitions
- Set number of Tx and Rx queues bassed on underlying hardware. Define
separate macros for maximum and supported numbers of Tx and Rx queues
based on underlying hardware. Take VLAN header into account for MTU
calculation. Default to INTx mode when pci_enable_msix() fails. Set a
bit in Rx poll routine, check and wait for that bit to be cleared in
the cleanup routine before proceeding.
- The TX and Rx coalesce settings are programmed in steps of 5 us. The value
that are not divisible by 5 are rounded to the next lower number. This was
causing the value os 1 to 4 to be rounded to 0, which is an invalid setting.
When creating Rx and Tx object, we are currently assigning the default
values of Rx and Tx coalescing_timeo. If these values are changed in the
driver to a different value, the change is lost during such operations as
MTU change. In order to avoid that, pass the configured value of
coalescing_timeo before Rx and Tx object creation. Fix
bnad_tx_coalescing_timeo_set() so it applies to all the Tx objects.
- Reorg uninitialization path in case of pci_probe failure.
- Hardware clock setup changes to pass asic generation, port modes and
asic mode as part firmware boot parameters to firmware.
- FW mailbox interface changes to defined asic specific mailbox interfaces.
h/w mailbox interfaces take 8-bit FIDs and 2-bit port id for owner. Cleaned
up mailbox definitions and usage for new and old HW. Eliminated usage of
ASIC ID. MSI-X vector assignment and programming done by firmware. Fixed
host offsets for CPE/RME queue registers.
- Implement polling mechanism for FW ready to have poll mechanism replaces
the current interrupt based FW READY method. The timer based poll routine
in IOC will query the ioc_fwstate register to see if there is a state
change in FW, and sends the READY event. Removed infrastructure needed to
support mbox READY event from fw as well as IOC code.
- Move FW init to HW init. Handle the case where PCI mapping goes away when
IOCPF state machine is waiting for semaphore.
- Add IOC mbox call back to client indicating that the command is sent.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moves the Brocade driver into drivers/net/ethernet/brocade/ and make
the necessary Kconfig and Makefile changes.
CC: Rasesh Mody <rmody@brocade.com>
CC: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
