| Age | Commit message (Collapse) | Author |
|---|
|
cxgb4_netdev maybe lead to dead lock, since it uses a spin lock, and be called
in both thread and softirq context, but not disable BH, the lockdep report is
below; In fact, cxgb4_netdev only reads adap_rcu_list with RCU protection, so
not need to hold spin lock again.
=================================
[ INFO: inconsistent lock state ]
3.14.7+ #24 Tainted: G C O
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
radvd/3794 [HC0[0]:SC1[1]:HE1:SE0] takes:
(adap_rcu_lock){+.?...}, at: [<ffffffffa09989ea>] clip_add+0x2c/0x116 [cxgb4]
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810fca81>] __lock_acquire+0x34a/0xe48
[<ffffffff810fd98b>] lock_acquire+0x82/0x9d
[<ffffffff815d6ff8>] _raw_spin_lock+0x34/0x43
[<ffffffffa09989ea>] clip_add+0x2c/0x116 [cxgb4]
[<ffffffffa0998beb>] cxgb4_inet6addr_handler+0x117/0x12c [cxgb4]
[<ffffffff815da98b>] notifier_call_chain+0x32/0x5c
[<ffffffff815da9f9>] __atomic_notifier_call_chain+0x44/0x6e
[<ffffffff815daa32>] atomic_notifier_call_chain+0xf/0x11
[<ffffffff815b1356>] inet6addr_notifier_call_chain+0x16/0x18
[<ffffffffa01f72e5>] ipv6_add_addr+0x404/0x46e [ipv6]
[<ffffffffa01f8df0>] addrconf_add_linklocal+0x5f/0x95 [ipv6]
[<ffffffffa01fc3e9>] addrconf_notify+0x632/0x841 [ipv6]
[<ffffffff815da98b>] notifier_call_chain+0x32/0x5c
[<ffffffff810e09a1>] __raw_notifier_call_chain+0x9/0xb
[<ffffffff810e09b2>] raw_notifier_call_chain+0xf/0x11
[<ffffffff8151b3b7>] call_netdevice_notifiers_info+0x4e/0x56
[<ffffffff8151b3d0>] call_netdevice_notifiers+0x11/0x13
[<ffffffff8151c0a6>] netdev_state_change+0x1f/0x38
[<ffffffff8152f004>] linkwatch_do_dev+0x3b/0x49
[<ffffffff8152f184>] __linkwatch_run_queue+0x10b/0x144
[<ffffffff8152f1dd>] linkwatch_event+0x20/0x27
[<ffffffff810d7bc0>] process_one_work+0x1cb/0x2ee
[<ffffffff810d7e3b>] worker_thread+0x12e/0x1fc
[<ffffffff810dd391>] kthread+0xc4/0xcc
[<ffffffff815dc48c>] ret_from_fork+0x7c/0xb0
irq event stamp: 3388
hardirqs last enabled at (3388): [<ffffffff810c6c85>]
__local_bh_enable_ip+0xaa/0xd9
hardirqs last disabled at (3387): [<ffffffff810c6c2d>]
__local_bh_enable_ip+0x52/0xd9
softirqs last enabled at (3288): [<ffffffffa01f1d5b>]
rcu_read_unlock_bh+0x0/0x2f [ipv6]
softirqs last disabled at (3289): [<ffffffff815ddafc>]
do_softirq_own_stack+0x1c/0x30
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(adap_rcu_lock);
<Interrupt>
lock(adap_rcu_lock);
*** DEADLOCK ***
5 locks held by radvd/3794:
#0: (sk_lock-AF_INET6){+.+.+.}, at: [<ffffffffa020b85a>]
rawv6_sendmsg+0x74b/0xa4d [ipv6]
#1: (rcu_read_lock){.+.+..}, at: [<ffffffff8151ac6b>]
rcu_lock_acquire+0x0/0x29
#2: (rcu_read_lock){.+.+..}, at: [<ffffffffa01f4cca>]
rcu_lock_acquire.constprop.16+0x0/0x30 [ipv6]
#3: (rcu_read_lock){.+.+..}, at: [<ffffffff810e09b4>]
rcu_lock_acquire+0x0/0x29
#4: (rcu_read_lock){.+.+..}, at: [<ffffffffa0998782>]
rcu_lock_acquire.constprop.40+0x0/0x30 [cxgb4]
stack backtrace:
CPU: 7 PID: 3794 Comm: radvd Tainted: G C O 3.14.7+ #24
Hardware name: Supermicro X7DBU/X7DBU, BIOS 6.00 12/03/2007
ffffffff81f15990 ffff88012fdc36a8 ffffffff815d0016 0000000000000006
ffff8800c80dc2a0 ffff88012fdc3708 ffffffff815cc727 0000000000000001
0000000000000001 ffff880100000000 ffffffff81015b02 ffff8800c80dcb58
Call Trace:
<IRQ> [<ffffffff815d0016>] dump_stack+0x4e/0x71
[<ffffffff815cc727>] print_usage_bug+0x1ec/0x1fd
[<ffffffff81015b02>] ? save_stack_trace+0x27/0x44
[<ffffffff810fbfaa>] ? check_usage_backwards+0xa0/0xa0
[<ffffffff810fc640>] mark_lock+0x11b/0x212
[<ffffffff810fca0b>] __lock_acquire+0x2d4/0xe48
[<ffffffff810fbfaa>] ? check_usage_backwards+0xa0/0xa0
[<ffffffff810fbff6>] ? check_usage_forwards+0x4c/0xa6
[<ffffffff810c6c8a>] ? __local_bh_enable_ip+0xaf/0xd9
[<ffffffff810fd98b>] lock_acquire+0x82/0x9d
[<ffffffffa09989ea>] ? clip_add+0x2c/0x116 [cxgb4]
[<ffffffffa0998782>] ? rcu_read_unlock+0x23/0x23 [cxgb4]
[<ffffffff815d6ff8>] _raw_spin_lock+0x34/0x43
[<ffffffffa09989ea>] ? clip_add+0x2c/0x116 [cxgb4]
[<ffffffffa09987b0>] ? rcu_lock_acquire.constprop.40+0x2e/0x30 [cxgb4]
[<ffffffffa0998782>] ? rcu_read_unlock+0x23/0x23 [cxgb4]
[<ffffffffa09989ea>] clip_add+0x2c/0x116 [cxgb4]
[<ffffffffa0998beb>] cxgb4_inet6addr_handler+0x117/0x12c [cxgb4]
[<ffffffff810fd99d>] ? lock_acquire+0x94/0x9d
[<ffffffff810e09b4>] ? raw_notifier_call_chain+0x11/0x11
[<ffffffff815da98b>] notifier_call_chain+0x32/0x5c
[<ffffffff815da9f9>] __atomic_notifier_call_chain+0x44/0x6e
[<ffffffff815daa32>] atomic_notifier_call_chain+0xf/0x11
[<ffffffff815b1356>] inet6addr_notifier_call_chain+0x16/0x18
[<ffffffffa01f72e5>] ipv6_add_addr+0x404/0x46e [ipv6]
[<ffffffff810fde6a>] ? trace_hardirqs_on+0xd/0xf
[<ffffffffa01fb634>] addrconf_prefix_rcv+0x385/0x6ea [ipv6]
[<ffffffffa0207950>] ndisc_rcv+0x9d3/0xd76 [ipv6]
[<ffffffffa020d536>] icmpv6_rcv+0x592/0x67b [ipv6]
[<ffffffff810c6c85>] ? __local_bh_enable_ip+0xaa/0xd9
[<ffffffff810c6c85>] ? __local_bh_enable_ip+0xaa/0xd9
[<ffffffff810fd8dc>] ? lock_release+0x14e/0x17b
[<ffffffffa020df97>] ? rcu_read_unlock+0x21/0x23 [ipv6]
[<ffffffff8150df52>] ? rcu_read_unlock+0x23/0x23
[<ffffffffa01f4ede>] ip6_input_finish+0x1e4/0x2fc [ipv6]
[<ffffffffa01f540b>] ip6_input+0x33/0x38 [ipv6]
[<ffffffffa01f5557>] ip6_mc_input+0x147/0x160 [ipv6]
[<ffffffffa01f4ba3>] ip6_rcv_finish+0x7c/0x81 [ipv6]
[<ffffffffa01f5397>] ipv6_rcv+0x3a1/0x3e2 [ipv6]
[<ffffffff8151ef96>] __netif_receive_skb_core+0x4ab/0x511
[<ffffffff810fdc94>] ? mark_held_locks+0x71/0x99
[<ffffffff8151f0c0>] ? process_backlog+0x69/0x15e
[<ffffffff8151f045>] __netif_receive_skb+0x49/0x5b
[<ffffffff8151f0cf>] process_backlog+0x78/0x15e
[<ffffffff8151f571>] ? net_rx_action+0x1a2/0x1cc
[<ffffffff8151f47b>] net_rx_action+0xac/0x1cc
[<ffffffff810c69b7>] ? __do_softirq+0xad/0x218
[<ffffffff810c69ff>] __do_softirq+0xf5/0x218
[<ffffffff815ddafc>] do_softirq_own_stack+0x1c/0x30
<EOI> [<ffffffff810c6bb6>] do_softirq+0x38/0x5d
[<ffffffffa01f1d5b>] ? ip6_copy_metadata+0x156/0x156 [ipv6]
[<ffffffff810c6c78>] __local_bh_enable_ip+0x9d/0xd9
[<ffffffffa01f1d88>] rcu_read_unlock_bh+0x2d/0x2f [ipv6]
[<ffffffffa01f28b4>] ip6_finish_output2+0x381/0x3d8 [ipv6]
[<ffffffffa01f49ef>] ip6_finish_output+0x6e/0x73 [ipv6]
[<ffffffffa01f4a70>] ip6_output+0x7c/0xa8 [ipv6]
[<ffffffff815b1bfa>] dst_output+0x18/0x1c
[<ffffffff815b1c9e>] ip6_local_out+0x1c/0x21
[<ffffffffa01f2489>] ip6_push_pending_frames+0x37d/0x427 [ipv6]
[<ffffffff81558af8>] ? skb_orphan+0x39/0x39
[<ffffffffa020b85a>] ? rawv6_sendmsg+0x74b/0xa4d [ipv6]
[<ffffffffa020ba51>] rawv6_sendmsg+0x942/0xa4d [ipv6]
[<ffffffff81584cd2>] inet_sendmsg+0x3d/0x66
[<ffffffff81508930>] __sock_sendmsg_nosec+0x25/0x27
[<ffffffff8150b0d7>] sock_sendmsg+0x5a/0x7b
[<ffffffff810fd8dc>] ? lock_release+0x14e/0x17b
[<ffffffff8116d756>] ? might_fault+0x9e/0xa5
[<ffffffff8116d70d>] ? might_fault+0x55/0xa5
[<ffffffff81508cb1>] ? copy_from_user+0x2a/0x2c
[<ffffffff8150b70c>] ___sys_sendmsg+0x226/0x2d9
[<ffffffff810fcd25>] ? __lock_acquire+0x5ee/0xe48
[<ffffffff810fde01>] ? trace_hardirqs_on_caller+0x145/0x1a1
[<ffffffff8118efcb>] ? slab_free_hook.isra.71+0x50/0x59
[<ffffffff8115c81f>] ? release_pages+0xbc/0x181
[<ffffffff810fd99d>] ? lock_acquire+0x94/0x9d
[<ffffffff81115e97>] ? read_seqcount_begin.constprop.25+0x73/0x90
[<ffffffff8150c408>] __sys_sendmsg+0x3d/0x5b
[<ffffffff8150c433>] SyS_sendmsg+0xd/0x19
[<ffffffff815dc53d>] system_call_fastpath+0x1a/0x1f
Reported-by: Ben Greear <greearb@candelatech.com>
Cc: Casey Leedom <leedom@chelsio.com>
Cc: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Select the appropriate hw mtu index and initial sequence number to optimize
hw memory performance.
Add new cxgb4_best_aligned_mtu() which allows callers to provide enough
information to be used to [possibly] select an MTU which will result in the
TCP Data Segment Size (AKA Maximum Segment Size) to be an aligned value.
If an RTR message exhange is required, then align the ISS to 8B - 1 + 4, so
that after the SYN the send seqno will align on a 4B boundary. The RTR
message exchange will leave the send seqno aligned on an 8B boundary.
If an RTR is not required, then align the ISS to 8B - 1. The goal is
to have the send seqno be 8B aligned when we send the first FPDU.
Based on original work by Casey Leedom <leeedom@chelsio.com> and
Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently indirect interrupts for RDMA CQs funnel through the LLD's RDMA
RXQs, which also handle direct interrupts for offload CPLs during RDMA
connection setup/teardown. The intended T4 usage model, however, is to
have indirect interrupts flow through dedicated IQs. IE not to mix
indirect interrupts with CPL messages in an IQ. This patch adds the
concept of RDMA concentrator IQs, or CIQs, setup and maintained by the
LLD and exported to iw_cxgb4 for use when creating CQs. RDMA CPLs will
flow through the LLD's RDMA RXQs, and CQ interrupts flow through the
CIQs.
Design:
cxgb4 creates and exports an array of CIQs for the RDMA ULD. These IQs
are sized according to the max available CQs available at adapter init.
In addition, these IQs don't need FL buffers since they only service
indirect interrupts. One CIQ is setup per RX channel similar to the
RDMA RXQs.
iw_cxgb4 will utilize these CIQs based on the vector value passed into
create_cq(). The num_comp_vectors advertised by iw_cxgb4 will be the
number of CIQs configured, and thus the vector value will be the index
into the array of CIQs.
Based on original work by Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add handling for " 8 GT/s" in print_port_info().
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using addressof then casting to the original type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast.cocci
@@
type T;
T foo;
@@
- (T *)&foo
+ &foo
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current logic suffers from a slow response time to disable user DB
usage, and also fails to avoid DB FIFO drops under heavy load. This commit
fixes these deficiencies and makes the avoidance logic more optimal.
This is done by more efficiently notifying the ULDs of potential DB
problems, and implements a smoother flow control algorithm in iw_cxgb4,
which is the ULD that puts the most load on the DB fifo.
Design:
cxgb4:
Direct ULD callback from the DB FULL/DROP interrupt handler. This allows
the ULD to stop doing user DB writes as quickly as possible.
While user DB usage is disabled, the LLD will accumulate DB write events
for its queues. Then once DB usage is reenabled, a single DB write is
done for each queue with its accumulated write count. This reduces the
load put on the DB fifo when reenabling.
iw_cxgb4:
Instead of marking each qp to indicate DB writes are disabled, we create
a device-global status page that each user process maps. This allows
iw_cxgb4 to only set this single bit to disable all DB writes for all
user QPs vs traversing the idr of all the active QPs. If the libcxgb4
doesn't support this, then we fall back to the old approach of marking
each QP. Thus we allow the new driver to work with an older libcxgb4.
When the LLD upcalls iw_cxgb4 indicating DB FULL, we disable all DB writes
via the status page and transition the DB state to STOPPED. As user
processes see that DB writes are disabled, they call into iw_cxgb4
to submit their DB write events. Since the DB state is in STOPPED,
the QP trying to write gets enqueued on a new DB "flow control" list.
As subsequent DB writes are submitted for this flow controlled QP, the
amount of writes are accumulated for each QP on the flow control list.
So all the user QPs that are actively ringing the DB get put on this
list and the number of writes they request are accumulated.
When the LLD upcalls iw_cxgb4 indicating DB EMPTY, which is in a workq
context, we change the DB state to FLOW_CONTROL, and begin resuming all
the QPs that are on the flow control list. This logic runs on until
the flow control list is empty or we exit FLOW_CONTROL mode (due to
a DB DROP upcall, for example). QPs are removed from this list, and
their accumulated DB write counts written to the DB FIFO. Sets of QPs,
called chunks in the code, are removed at one time. The chunk size is 64.
So 64 QPs are resumed at a time, and before the next chunk is resumed, the
logic waits (blocks) for the DB FIFO to drain. This prevents resuming to
quickly and overflowing the FIFO. Once the flow control list is empty,
the db state transitions back to NORMAL and user QPs are again allowed
to write directly to the user DB register.
The algorithm is designed such that if the DB write load is high enough,
then all the DB writes get submitted by the kernel using this flow
controlled approach to avoid DB drops. As the load lightens though, we
resume to normal DB writes directly by user applications.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without a shutdown handler, T4 cards behave very badly after a kexec.
Some firmware calls return errors indicating allocation failures, for
example. This is probably because thouse resources were not released by
a BYE message to the firmware, for example.
Using the remove handler guarantees we will use a well tested path.
With this patch I applied, I managed to use kexec multiple times and
probe and iSCSI login worked every time.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethtool speed values are just numbers of megabits and there is no need
to add SPEED_40000. To be consistent, use integer constants directly
for all speeds.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unused registers for registers list, and add missing ones
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Query firmware to see whether we're allowed to use T5 ULPTX MEMWRITE DSGL
capabilities. Also pass that information to Upper Layer Drivers via the
new (struct cxgb4_lld_info).ulptx_memwrite_dsgl boolean.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on original work by Divy Le Ray.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we attach to adapter, print VPD Part Number instead of Engineering Change field.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also, create a new Common Code interface to translate Firmware Port Technology
Type values (enum fw_port_type) to string descriptions. This will allow us
to maintain the description translation table in one place rather than in
every driver.
Based on original work by Scott Bardone and Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Dimitris Michailidis <dm@chelsio.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The adapter is freed before we check its flags. It was caused
by commit 144be3d ("net/cxgb4: Avoid disabling PCI device for
towice"). The problem was reported by Intel's "0-day" tool.
The patch fixes it to avoid reverting commit 144be3d.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We possibly retrieve the adapter's statistics during EEH recovery
and that should be disallowed. Otherwise, it would possibly incur
replicate EEH error and EEH recovery is going to fail eventually.
The patch reuses statistics lock and checks net_device is attached
before going to retrieve statistics, so that the problem can be
avoided.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we have EEH error happens to the adapter and we have to remove
it from the system for some reasons (e.g. more than 5 EEH errors
detected from the device in last hour), the adapter will be disabled
for towice separately by eeh_err_detected() and remove_one(), which
will incur following unexpected backtrace. The patch tries to avoid
it.
WARNING: at drivers/pci/pci.c:1431
CPU: 12 PID: 121 Comm: eehd Not tainted 3.13.0-rc7+ #1
task: c0000001823a3780 ti: c00000018240c000 task.ti: c00000018240c000
NIP: c0000000003c1e40 LR: c0000000003c1e3c CTR: 0000000001764c5c
REGS: c00000018240f470 TRAP: 0700 Not tainted (3.13.0-rc7+)
MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI> CR: 28000024 XER: 00000004
CFAR: c000000000706528 SOFTE: 1
GPR00: c0000000003c1e3c c00000018240f6f0 c0000000010fe1f8 0000000000000035
GPR04: 0000000000000000 0000000000000000 00000000003ae509 0000000000000000
GPR08: 000000000000346f 0000000000000000 0000000000000000 0000000000003fef
GPR12: 0000000028000022 c00000000ec93000 c0000000000c11b0 c000000184ac3e40
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR24: 0000000000000000 c0000000009398d8 c00000000101f9c0 c0000001860ae000
GPR28: c000000182ba0000 00000000000001f0 c0000001860ae6f8 c0000001860ae000
NIP [c0000000003c1e40] .pci_disable_device+0xd0/0xf0
LR [c0000000003c1e3c] .pci_disable_device+0xcc/0xf0
Call Trace:
[c0000000003c1e3c] .pci_disable_device+0xcc/0xf0 (unreliable)
[d0000000073881c4] .remove_one+0x174/0x320 [cxgb4]
[c0000000003c57e0] .pci_device_remove+0x60/0x100
[c00000000046396c] .__device_release_driver+0x9c/0x120
[c000000000463a20] .device_release_driver+0x30/0x60
[c0000000003bcdb4] .pci_stop_bus_device+0x94/0xd0
[c0000000003bcf48] .pci_stop_and_remove_bus_device+0x18/0x30
[c00000000003f548] .pcibios_remove_pci_devices+0xa8/0x140
[c000000000035c00] .eeh_handle_normal_event+0xa0/0x3c0
[c000000000035f50] .eeh_handle_event+0x30/0x2b0
[c0000000000362c4] .eeh_event_handler+0xf4/0x1b0
[c0000000000c12b8] .kthread+0x108/0x130
[c00000000000a168] .ret_from_kernel_thread+0x5c/0x74
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds API cxgb4_select_ntuple so as to enable Upper Level Drivers to correctly
calculate the tuple fields.
Adds constant definitions for TP_VLAN_PRI_MAP for the Compressed
Filter Tuple field widths and structures and uses them.
Also, the CPL Parameters field for T5 is 40 bits so we need to prototype
cxgb4_select_ntuple() to calculate and return u64 values.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 uses 2 TIDs with CLIP enabled and 4 TIDs without CLIP.
Currently we are incrementing STIDs in use by 1 for both IPv4 and IPv6 which
is wrong.
Further, driver currently does not have interface to query if CLIP is programmed
for particular IPv6 address. So, in this patch we increment/decrement TIDs in use
by 4 for IPv6 assuming absence of CLIP. Such assumption keeps us on safe side and
we don't end up allocating more stids for IPv6 than actually supported.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LE workaround code is incorrectly reusing the TCAM TIDs
(meant for allocation by firmware in case of hash collisions) for filter
servers. This patch assigns the filter server TIDs properly starting from
sftid_base index.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were creating LE Workaround Server Filters without specifying
IPPROTO_TCP (6) in the filters (when F_PROTOCOL is set in TP_VLAN_PRI_MAP).
This meant that UDP packets with matching IP Addresses/Ports would get
caught up in the filter and be delivered to ULDs like iw_cxgb4.
So, include the protocol information in the server filter properly.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating offload server entries, an IPv6 passive connection request
can trigger a reply with a null STID, whereas the driver would expect
the reply 'STID to match the value used for the request.
This happens due to h/w limitation on T4 and T5.
This patch ensures that STID 0 is never used if the stid range starts
from zero.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It needs a list_head *iter, so add it wherever needed. Use both non-rcu and
rcu variants.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When driver registration fails, we need to clean up the resources allocated
before. cxgb4 missed to destroy the workqueue allocated at the very beginning.
This patch destroies the workqueue when registration fails.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
|
|
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
|
|
Don't emit OOM warnings when k.alloc calls fail when
there there is a v.alloc immediately afterwards.
Converted a kmalloc/vmalloc with memset to kzalloc/vzalloc.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The Compressed LIP region is used to hold a limited number of Local
IPv6 addresses. This region is primarily used to reduce the TCAM
space consumed for an IPv6 offloaded connection. A 128-bit LIP will
be reduced to 13-bit and stored in the TCAM if there is a match
between the IPv6 tuple's LIP and the one stored in the CLIP region.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Add cxgb4_create_server6 and cxgb4_remove_server routines to create
and remove listening IPv6 servers.
Return success (0) from cxgb4_create_server in case of ctrl queue
congestion since in case of congestion, passive open request gets
queued and gets processed later. If a non-zero value were returned it
would be treated as an error and the ULD would free STID, which can
result in an error in passive open reply.
Add cpl structure for active open request with IPv6 address for T5.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
the MASTER_PF
Forcing uninitialized state allows us to upgrade and reinitialize the adapter.
FW_VERSION_T4 = 1.4.0.0
FW_VERSION_T5 = 0.0.0.0
At this point driver supports above and greater than above version of firmware.
If it doesn't find the required firmware version than it forces the adapter to
be reinitialized as shown below.
1) If FW_ON_ADAPTER < FW_VERSION and we're the MASTER_PF force uninitialized
state and a FW upgrade if available.
- If FW_ON_ADAPTER < /lib/firmware/cxgb4/t*fw.bin we will update the
adapters FW.
- If FW_ON_ADAPTER >= /lib/firmware/cxgb4/t*fw.bin don't upgrade FW.
- If upgrade_fw() fails force reinitialization of the adapter anyways,
it might still work.
Either way forcing the uninitialized state allows cxgb4 reinitialize FW.
2) If FW_ON_ADAPTER >= FW_VERSION driver follows normal path.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 636f9d371f70f22961fd598fe18380057518ca31 ("cxgb4: Add
support for T4 configuration file"), t4_fw_hello may return a positive
value instead of 0 for success. The recovery code tests only for zero
and fails recovery for any other value.
This fix tests for negative error values and fails only on those cases.
Error recovery after an error injection works after this change.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer firmware can post CPL_SGE_EGR_UPDATE message encapsulated in a
CPL_FW4_MSG as follows
flit0 rss_header (if DropRSS == 0 in IQ context)
flit1 CPL_FW4_MSG cpl
flit2 rss_header w/opcode CPL_SGE_EGR_UPDATE
flit3 CPL_SGE_EGR_UPDATE cpl
So FW4_MSG CPLs with a newly created type of FW_TYPE_RSSCPL have the
CPL_SGE_EGR_UPDATE CPL message in flit 2 of the FW4_MSG. Firmware can still
post regular CPL_SGE_EGR_UPDATE messages, so the drivers need to handle
both.
This patch also writes a new parameter to firmware requesting encapsulated
EGR_UPDATE. This allows firmware with this support to not break older drivers.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All T5 adapters will only support VFs on PF0-3 despite the ability of the
hardware to support them on PF4-7. This keeps our T4 and T5 adapters more
similar which simplifies host driver software.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
