| Age | Commit message (Collapse) | Author |
|---|
|
efx_mcdi_get_board_cfg() uses a buffer for the firmware response that
is only large enough to hold subtypes for the originally defined set
of NVRAM partitions. Longer responses are truncated, and we may read
off the end of the buffer when copying out subtypes for additional
partitions. In particular, this can result in the MTD partition for
an FPGA bitfile being named e.g. 'eth5 sfc_fpga:00' when it should be
'eth5 sfc_fpga:01'. This means the firmware update tool (sfupdate)
can't tell which bitfile should be written to the partition.
Correct the response buffer size.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
efx_mcdi_poll() uses get_seconds() to read the current time and to
implement a polling timeout. The use of this function was chosen
partly because it could easily be replaced in a co-sim environment
with a macro that read the simulated time.
Unfortunately the real get_seconds() returns the system time (real
time) which is subject to adjustment by e.g. ntpd. If the system time
is adjusted forward during a polled MCDI operation, the effective
timeout can be shorter than the intended 10 seconds, resulting in a
spurious failure. It is also possible for a backward adjustment to
delay detection of a areal failure.
Use jiffies instead, and change MCDI_RPC_TIMEOUT to be denominated in
jiffies. Also correct rounding of the timeout: check time > finish
(or rather time_after(time, finish)) and not time >= finish.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
If the MC reboots then the stats it reports to us will have been
reset. We need to reset ours to get efx_update_diff_stat() working
properly.
(Ideally we would maintain stats across the reboot, but as this should
only happen immediately after a firmware upgrade it's not really worth
the trouble.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
efx_mcdi_rpc_start() returns a negative value on error or zero on
success. However one caller that can't properly handle failure then
does WARN_ON(rc > 0). Change it to WARN_ON(rc < 0).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
MCDI supports requests up to 252 bytes long, which is only enough to
pass 63 RX queue IDs to MC_CMD_FLUSH_RX_QUEUES. However a VF may have
up to 64 RX queues, and if we try to flush them all we will generate
an over-length request and BUG() in efx_mcdi_copyin(). Currently
all VF drivers limit themselves to 32 RX queues, so reducing the
limit to 63 does no harm.
Also add a BUILD_BUG_ON in efx_mcdi_flush_rxqs() so we remember to
deal with the same problem there if EFX_MAX_CHANNELS is increased.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
On big-endian systems the MTD partition names currently have mangled
subtype numbers and are not recognised by the firmware update tool
(sfupdate).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
This work is based on prior code by Andrew Jackson
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
[bwh:
- Add byte order conversion in efx_ptp_send_times()
- Simplify conversion of PPS event times
- Add the built-in vs module check to CONFIG_SFC_PTP dependencies]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
For NIC/System time synchonisation efx_mcdi_rpc needs to be split in
efx_mcdi_rpc_start and efx_mcdi_rpc_finish operations.
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Fix CID 113952 in Coverity report on Linux.
This is the one instance where we don't, and shouldn't, check the
return code from efx_mcdi_rpc(). It wasn't immediately obvious to me
why we didn't, so I think an explanation is in order.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
On the SFC9000 family, each port has 1024 Virtual Interfaces (VIs),
each with an RX queue, a TX queue, an event queue and a mailbox
register. These may be assigned to up to 127 SR-IOV virtual functions
per port, with up to 64 VIs per VF.
We allocate an extra channel (IRQ and event queue only) to receive
requests from VF drivers.
There is a per-port limit of 4 concurrent RX queue flushes, and queue
flushes may be initiated by the MC in response to a Function Level
Reset (FLR) of a VF. Therefore, when SR-IOV is in use, we submit all
flush requests via the MC.
The RSS indirection table is shared with VFs, so the number of RX
queues used in the PF is limited to the number of VIs per VF.
This is almost entirely the work of Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The SFC9000-family controllers have firmware to manage all board
peripherals including temperature, heat sink continuity and voltage
sensors. The firmware reports sensor alarms, which we log, and
will shut down the board if necessary.
Some users may want to monitor their boards more closely, so add an
hwmon driver that exposes all sensors reported by the firmware. Move
efx_mcdi_sensor_event() into the new file so it can share the array of
sensor labels with the hwmon driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
These are defined alongside the firmware protocol in mcdi_pcol.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
When the MC reboots, either as part of a firmware upgrade or due to a
bug, it attempts to complete (with an error) any requests that were
outstanding before the reboot. Since there is an inherent race
condition in checking this, it will also write to a status word in
shared memory.
If we look at each of these separately, we may detect each reboot
twice, resulting in a spurious command failure after a firmware
upgrade or frustrating recovery from a firmware bug. Instead, if a
request completion indicates a reboot, we must poll and clear the
status word.
This bug was previously masked by use of an incorrect address for the
status word. Fix that, using the definition now included in
mcdi_pcol.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Some commands and constants have been renamed; adjust the code
accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Fix the following warnings:
WARNING: struct dev_pm_ops should normally be const
WARNING: static const char * array should probably be static const char * const
Similarly const-qualify struct i2c_board_info, struct i2c_algo_bit_data,
struct efx_ethtool_stat, struct efx_mtd_ops and struct siena_nvram_type_info.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Conflicts:
MAINTAINERS
drivers/net/Kconfig
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
drivers/net/ethernet/broadcom/tg3.c
drivers/net/wireless/iwlwifi/iwl-pci.c
drivers/net/wireless/iwlwifi/iwl-trans-tx-pcie.c
drivers/net/wireless/rt2x00/rt2800usb.c
drivers/net/wireless/wl12xx/main.c
|
|
Moves the Solarflare drivers into drivers/net/ethernet/sfc/ and
make the necessary Kconfig and Makefile changes.
CC: Steve Hodgson <shodgson@solarflare.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
