| Age | Commit message (Collapse) | Author |
|---|
|
Renames some autoneg/speed variables to be more consistent with check_link,
get_link_capabilities, and setup_link function calls. Initializes instances
of autoneg.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The device lookup neglected to do a pci_dev_put() to decrement the
device reference count.
Reported-by: Elena Gurevich <elena.gurevich@toganetworks.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Check for up2tc change and call ixgbe_dcbnl_devreset() if the mapping has
changed but the number of TC's in use has not changed.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Under heavy CPU load, changing, ring size/mtu/etc. could result in transmit
timeout, since stop-start port might take more than 10 seconds.
Calling netif_detach_device to prevent tx queue transmit timeout.
netif_detach_device() is not called under ndo_stop, because netif_carrier_off
will prevent the timeout, and device should not be marked as not present, or
else user won't be able to start it later on.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mac reassignments should only be done when not supported by the firmware. To
accomplish that, checking firmware capability bit to know whether we should
reassign macs in the driver.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Firmware dynamically changes flow steering hash configuration from covering
L2 only to "full" L2/L3/L4 mode needed. The dynamic change allows the driver
to set hard coded hash configuration which is changed by the firmware from L2
to L2/L3/L4 when attaching the first L3/L4 flow steering rule and back to L2
when there are no more such rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of the driver unload flow, all steering rules must be deleted,
make sure to remove the rules that were set through ethtool.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
is down
Attaching steering rules while the interface is down is an invalid operation, block it.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vlan mask field should be validated and assigned according to the field
size which is 12 bits. Also replace the numeric 0xfff mask with existing kernel
macro.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When attaching flow steering rules via Ethtool accept only valid vlans IDs e.g
in the range: [0,4095].
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Destination mac is a mandatory specification for ip/udp steering rules.
When attaching multicast steering rules via ethtool the unicast mac of the
interface was added to the rule specification instead of the multicast mac.
The following commit sets the corresponding multicast mac for the rule multicast ip.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The allow_loopback flag was wrongly set using arithmetic bit operation, change
the code to use logical bit operation.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the fields for struct mlx4_net_trans_rule_hw_ctrl were packed into u32
and accessed through bit field operations. Expose and access them directly as
u8.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o ipv4 address was not getting programmed properly because of
improper byte order conversion
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* remove unused members(!): imask, ievent
* move space consuming interrupt name strings (int_name_* members) to
external structures, unessential for the driver's hot path
* keep high priority hot path data within the first 2 cache lines
This reduces struct gfar_priv_grp from 6 to 3 cache lines.
(Also fixed checkpatch warnings for the old code, in the process.)
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Factor out redundant code (improve readability, source code size).
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resize and regroup structure members to eliminate memory holes and
to pack the structure into 2 cache lines (from 3).
tx_ring_size was resized from 4 to 2 bytes and few members were re-grouped
in order to eliminate byte holes and achieve compactness.
Where possible, few members were grouped according to their usage and access
order (i.e. start_xmit vs. clean_tx_ring members), less important members
were pushed at the end.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add napi support
Before this patch
iperf -s -i 1
------------------------------------------------------------
Server listening on TCP port 5001
TCP window size: 85.3 KByte (default)
------------------------------------------------------------
[ 4] local 10.192.242.153 port 5001 connected with 10.192.242.138 port 50004
[ ID] Interval Transfer Bandwidth
[ 4] 0.0- 1.0 sec 41.2 MBytes 345 Mbits/sec
[ 4] 1.0- 2.0 sec 43.7 MBytes 367 Mbits/sec
[ 4] 2.0- 3.0 sec 42.8 MBytes 359 Mbits/sec
[ 4] 3.0- 4.0 sec 43.7 MBytes 367 Mbits/sec
[ 4] 4.0- 5.0 sec 42.7 MBytes 359 Mbits/sec
[ 4] 5.0- 6.0 sec 43.8 MBytes 367 Mbits/sec
[ 4] 6.0- 7.0 sec 43.0 MBytes 361 Mbits/sec
After this patch
[ 4] 2.0- 3.0 sec 51.6 MBytes 433 Mbits/sec
[ 4] 3.0- 4.0 sec 51.8 MBytes 435 Mbits/sec
[ 4] 4.0- 5.0 sec 52.2 MBytes 438 Mbits/sec
[ 4] 5.0- 6.0 sec 52.1 MBytes 437 Mbits/sec
[ 4] 6.0- 7.0 sec 52.1 MBytes 437 Mbits/sec
[ 4] 7.0- 8.0 sec 52.3 MBytes 439 Mbits/sec
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cleanup the format of ethoc.c to meet network driver style as
per checkpatch.pl.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
just as it should have been. It also helps
removing the, now unnecessary, workqueue.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch to use ndo_get_stats64 to get 64bit statistics.
Signed-off-by: Jamie Gloudon <jamie.gloudon@gmail.com>
Tested-by: Jamie Gloudon <jamie.gloudon@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
This series contains updates to e1000e, ixgbevf, igb and igbvf.
Majority of the patches are code cleanups of e1000e where code
is removed (Yeah!). The other two e1000e patches are fixes. The
first is to fix the maximum frame size for 82579 devices. The second
fix is to resolve an issue with devices other than 82579 that suffer
from dropped transactions on platforms with deep C-states when
jumbo frames are enabled.
The ixgbevf patch is to ensure that the driver fetches the correct,
refreshed value for link status and speed when the values have changed.
The igb and igbvf patches are a solution to an issue Stefan Assmann
reported, where when the PF is up and igbvf is loaded, the MAC address
is not generated using eth_hw_addr_random().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tighten up some of the code surrounding MAC addresses. Since the PF is
now giving all zeros instead of a random address, check for this case
and generate a random address. This ensures that we always know when we
have a random address and udev won't get upset about it.
Additionally, tighten up some of the log messages and clean up the
formatting.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the user has not assigned a MAC address to a VM, then don't give it a
random one. Instead, just give it zeros and let it figure out what to do
with them.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A recent change makes it necessary to set get_link_status to ensure that
the driver fetches the correct, refreshed value for link status and speed
when it has changed in the physical function device.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Code was removed but the applicable comments were not.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove unnecessary #include, forward prototype of struct e1000_adapter and
an empty comment; fix a comment which mentions "static data for the MAC"
which is not applicable to the following struct; and cleanup some
whitespace issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
All references to E1000_ERT_2048 have been removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It has been found that devices other than 82579 (a.k.a. e1000_pch2lan)
suffer from dropped transactions on platforms with deep C-states when
jumbo frames are enabled. For example, LOMs on ICH9- and ICH10-based
platforms which recently had early-receive de-featured (for stability
reasons) suffer from this. To resolve this for all devices, when jumbo
frames are enabled set the PM QoS DMA latency request based on the size
of the receive packet buffer less one full frame.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The largest jumbo frame supported by the 82579 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove the function e1000e_commit_phy() and replace the few calls to it
with the same function pointer that it would call. The function pointer is
almost always set for the devices that access these code paths so there is
no risk of a NULL pointer dereference; for the few instances where the
function pointer might not be set (i.e. can be called for the few devices
which do not have this function pointer set), check for a valid function
pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove the function e1000_get_cable_length() and replace the two calls
to it with the same function pointer that it would call.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove the function e1000_get_phy_cfg_done() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In keeping with the e1000e driver function naming convention, the subject
function is renamed to indicate it is generic, i.e. it is applicable to
more than just a single MAC family (e.g. 80003es2lan, 82571, ich8lan).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove the function e1000_force_speed_duplex() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Replace the function e1000_set_d0_lplu_state() with the contents of it
coded in place of the single call to the function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
filters_lock might have been used while it was re-initialized.
Moved filters_lock and filters_list initialization to init_netdev instead of
alloc_resources which is called every time the device is configured.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a possible race where the TX completion handler can clean the
entire TX queue between the decision that the queue is full and actually
closing it. To avoid this situation, check again if the queue is really
full, if not, reopen the transmit and continue with sending the packet.
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Returning 0 (success) when in fact we are aborting the load, leads to kernel
panic when unloading the module. Fix that by returning the actual error code.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device multicast list is protected by netif_addr_lock_bh in the networking core, we should
use this locking practice in mlx4_en too.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When port is stopped and flow steering mode is not device managed: promisc QP
rule wasn't removed from MCG table.
Added code to remove it in all flow steering modes.
In addition, promsic rule removal should be in stop port and not in start
port - moved it accordingly.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Performing the DUMP_ETH_STATS firmware command outside the lock leads to kernel
panic when data structures such as RX/TX rings are freed in parallel, e.g when
one changes the mtu or ring sizes.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
