Age | Commit message (Collapse) | Author |
|
This patch adds a log message in case of POST timeout in Lancer to
help debugging failure cases. It also logs sliport_status register value in
case of POST timeout.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The support for this exists only in skyhawk FW.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the FW cmd to set flow control fails, the adapter state must simply
reflect the old values.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes a bit of duplication of code that initializes the en_flags.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, dwmac-rk uses a custom propety "phy_regulator" to get the name of the
right regulator to use to power on or power off the phy. This commit converts the
driver to use phy-supply devicetree property and the corresponding API, it cleans
the code a bit and make it simpler to maintain. This also replaces the property
phy_regulator by the standard property phy-supply in rk3288-evb-rk808.dts.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As these settings can be directly expressed from devicetree for both fixed
regulators and pmic-integrated regulators, it is more standard to set them
from dts and let the regulator framework use the right voltage informations
when it is used in the driver.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support to dump the rss table, rss_config, rss_key, rss_pf_config and
rss_vf_config
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support to dump the contents of the flash in the adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updated hardware documention shows the Rx flow control settings were
moved from the Rx queue operation mode register to a new Rx queue flow
control register. The old flow control settings are now reserved areas
of the Rx queue operation mode register. Update the code to use the new
register.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't update Tx tail descriptor if queue hasn't been stopped
and we know at least one more skb will be sent right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Don't update Tx tail descriptor if we queue hasn't been stopped and
we know at least one more skb will be sent right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Commit 5ac6f91d changed the igb driver to expose a zero (empty) mac
address to the VF on reset rather than a random one.
However, that behavioral change also requires igbvf driver changes
which can be hard especially when we want to talk to proprietary
guest OSs.
Looking at the code previous to the commit in Linux that made igbvf
work with empty mac addresses (8d56b6d), we can see that on reset
failure the driver will try to generate a new mac address with both
the old and the new code.
Furthermore, ixgbe does send reset failure when it detects an empty
mac address (35055928c).
So I think it's safe to make igb behave the same. With this patch I
can successfully run a Windows 8.1 guest with an empty mac address
and an assigned igbvf device that has no mac address set by the host.
If anyone is aware of a guest driver that chokes on NACK returns of
VF RESET commands, please speak up.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on feedback from the hardware team, 100us is too short of a time
to wait for the data path reset to complete and the recommendation is to
increase this timeout to 150us.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
fm10k supports up to 184 bytes of inner+outer headers. Add an initial
check to fail encap offload if these are too large.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
feature mask
The networking core does it for the driver during registration time.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i210 device offers a number of special PTP Hardware Clock features on
the Software Defined Pins (SDPs). This patch adds support for two of the
possible functions, namely time stamping external events, and periodic
output signals.
The assignment of PHC functions to the four SDP can be freely chosen by
the user.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i210 device can produce an interrupt on the full second. This
patch allows using this interrupt to generate an internal PPS event
for adjusting the kernel system time.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The time sync related interrupt registers may be manipulated from
different contexts. This patch protects the registers from being
asynchronously changed by the reset function.
Also, the patch removes a misleading comment. The reset function
is disabling a bunch of functions, not enabling them.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The code that handles the time sync interrupt is repeated in three
different places. This patch refactors the identical code blocks into
a single helper function.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.
It also cleans up how we clear the descriptor status bits. Previously they
were zeroed as a part of clearing the hdr_addr. However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems. Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared. As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.
It also cleans up how we clear the descriptor status bits. Previously they
were zeroed as a part of clearing the hdr_addr. However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems. Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared. As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
With the Intel 82527EI (driver: e1000e) there is an issue when running
the ptpd2 program, that leads to a kernel oops. The reason is here that
in e1000_xmit_frame() a work queue will be scheduled that has not been
initialized in this case. The work queue "tx_hwstamp_work" will only be
initialized if adapter->flags & FLAG_HAS_HW_TIMESTAMP set. This check
is missing in e1000_xmit_frame().
The following patch adds the missing check.
Signed-off-by: Mathias Koehrer <mathias.koehrer@etas.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
To be future-proof and for better readability the time comparisons are
modified to use time_after_eq() instead of plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
"sp->desc[i]" has 25 characters. "dev->name" has 15 characters. If we
used all 15 characters then the sprintf() would overflow.
I changed the "sprintf(sp->name, "%s Neterion %s"" to snprintf(), as
well, even though it can't overflow just to be consistent.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IRQs should only get activated when there is nothing to poll in the
queue any more and to after every poll.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
napi should get registered before the netdev and not after.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mii_check_media() does not update the link (carrier) state or log link
changes when the link mode is forced. Drivers using the mii library
must do this themselves, but most of them do not.
Instead of changing them all, provide a sensible default behaviour
similar to mii_check_link() when the mode is forced.
via-rhine depends on it being a no-op in this case, so make its call
to mii_check_media() conditional.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver connects and disconnects the PHY device whenever the
net device is brought up and down. The ethtool get_settings,
set_settings and nway_reset operations will dereference a null
or dangling pointer if called while it is down.
I think it would be preferable to keep the PHY connected, but there
may be good reasons not to.
As an immediate fix for this bug:
- Set the phydev pointer to NULL after disconnecting the PHY
- Change those three operations to return -ENODEV while the PHY is
not connected
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently net_device_ops::set_rx_mode is only implemented for
chips with a TSU (multiple address table). However we do need
to turn the PRM (promiscuous) flag on and off for other chips.
- Remove the unlikely() from the TSU functions that we may safely
call for chips without a TSU
- Make setting of the MCT flag conditional on the tsu capability flag
- Rename sh_eth_set_multicast_list() to sh_eth_set_rx_mode() and plumb
it into both net_device_ops structures
- Remove the previously-unreachable branch in sh_eth_rx_mode() that
would otherwise reset the flags to defaults for non-TSU chips
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enhances the NetCP gbe driver to support 10GbE subsystem
available in Keystone NetCP. The 3-port 10GbE switch sub-module contains
the following components:- 10GbE Switch, MDIO Module, 2 PCS-R Modules
(10GBase-R) and 2 SGMII modules (10/100/1000Base-T). The GBE driver
together with netcp core driver provides support for 10G Ethernet
on Keystone SoCs.
10GbE hardware spec is available at
http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=spruhj5&fileType=pdf
Cc: David Miller <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support for 1G Ethernet driver based on Keystone
NetCP hardware. The gigabit Ethernet (GbE) switch subsystem is one of the main
components of the network coprocessor (NETCP) peripheral. The purpose of the
gigabit Ethernet switch subsystem in the NETCP is to provide an interface to
transfer data between the host device and another connected device in
compliance with the Ethernet protocol. GbE consists of 5 port Ethernet Switch
module, 4 Serial Gigabit Media Independent Interface (SGMII) modules, MDIO
module and SerDes.
Driver for 5 port GbE switch and SGMII module is added in this patch. These
hardware modules along with netcp core driver provides Network driver functions
for 1G Ethernet.
Detailed hardware spec is available at
http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
Cc: David Miller <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The network coprocessor (NetCP) is a hardware accelerator available in
Keystone SoCs that processes Ethernet packets. NetCP consists of following
hardware components
1 Gigabit Ethernet (GbE) subsystem with a Ethernet switch sub-module to
send and receive packets.
2 Packet Accelerator (PA) module to perform packet classification
operations such as header matching, and packet modification operations
such as checksum generation.
3 Security Accelerator(SA) capable of performing IPSec operations on
ingress/egress packets.
4 An optional 10 Gigabit Ethernet Subsystem (XGbE) which includes a
3-port Ethernet switch sub-module capable of 10Gb/s and 1Gb/s rates
per Ethernet port.
5 Packet DMA and Queue Management Subsystem (QMSS) to enqueue and dequeue
packets and DMA the packets between memory and NetCP hardware components
described above.
NetCP core driver make use of the Keystone Navigator driver API to allocate
DMA channel for the Ethenet device and to handle packet queue/de-queue,
Please refer API's in include/linux/soc/ti/knav_dma.h and
drivers/soc/ti/knav_qmss.h for details.
NetCP driver consists of NetCP core driver and at a minimum Gigabit
Ethernet (GBE) module (1) driver to implement the Network device function.
Other modules (2,3) can be optionally added to achieve supported hardware
acceleration function. The initial version of the driver include NetCP
core driver and GBE driver modules.
Please refer Documentation/devicetree/bindings/net/keystone-netcp.txt
for design of the driver.
Cc: David Miller <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c03abd84634d (net: ethernet: cpsw: don't requests IRQs we don't
use) left one build breakage when NET_POLL_CONTROLLER is enabled.
Fix this build break by referring to the correct irqs_table array.
Fixes: c03abd84634d (net: ethernet: cpsw: don't requests IRQs we don't use)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add packet and byte counters for RX and TX paths.
$ ifconfig eth1
eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet6 fe80::5054:ff:fe12:3501 prefixlen 64 scopeid 0x20<link>
ether 52:54:00:12:35:01 txqueuelen 1000 (Ethernet)
RX packets 63 bytes 15813 (15.4 KiB)
RX errors 1 dropped 0 overruns 0 frame 0
TX packets 79 bytes 17991 (17.5 KiB)
TX errors 7 dropped 0 overruns 0 carrier 0 collisions 0
Rx / Tx errors tested by injecting faults in qemu's hardware model for Rocker.
v2:
- moved counter locations to avoid potential use after free per Florian's comment
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Scott Feldman <sfeldma@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPSW never uses RX_THRESHOLD or MISC interrupts. In
fact, they are always kept masked in their appropriate
IRQ Enable register.
Instead of allocating an IRQ that never fires, it's best
to remove that code altogether and let future patches
implement it if anybody needs those.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is in preparation for a nicer IRQ
handling scheme where we use different IRQ
handlers for each IRQ line (as it should be).
Later, we will also drop IRQs offset 0 and 3
because they are always disabled in this driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch benefits from newly introduced switchdev notifier and uses it
to propagate fdb learn events from rocker driver to bridge. That avoids
direct function calls and possible use by other listeners (ovs).
Suggested-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After a "page = alloc_page(mask);", we do not need to use
compound_head() : page already points to the right place.
This would be true even if using alloc_pages().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-01-16
This series contains updates to i40e and i40evf.
This series is a little bit larger than normal because two of the patches are
version bumps.
Shannon provides tweaks to i40e and i40evf to keep the firmware, software
and silicon validation in line together by removing unused and
deprecated code, adding define for iSCSI and fix queue mask size. Fix
i40e so we do not give up in the reset/rebuild process if DCB setup
fails, just handle it the same as in the probe setup. Cleans up PTP
log messages by removing the use of __func__ as we are not using that
any longer and removes the netdev name, since that can change and can
be misleading. Adds struct size checks to indirect and command
structs that were left out previously. Added admin queue API updates
(LLDP control, OEM OCSD and OCBB commands).
Kevin increases ASQ timeout for scenarios with multi-function devices.
Carolyn fixes a problem where the interrupts descriptions from the MSIx
configuration were truncating the needed bus info, which makes it hard
to distinguish configurations from port to port. Increased the string
buffer size in order to allow the full data to be displayed.
Sravanthi cleans up the dump stats string from debugfs.
Jacob updates i40e to only enable the PTP interrupt in PFs which have PTP
enabled, instead of blindly enabling the PTP interrupt flags for all PFs.
Also updated i40e so that we do not do Tx or Rx timestamps if we do not
have PTP enabled. Added the same check against pf->ptp_rx as we have
in Rx timestamp code path because it is possible that the user can
configure only Tx hardware timestamping so we do not want to check for
Rx timestamp hang since the software won't be handling them.
Neerav updates the driver to disable firmware LLDP agent for NICs with
a firmware version lower than v4.3 and added a message when this happens.
Adds parsing and reporting of iSCSI capability for a given device or
function, as well as adding support for iSCSI partition type with DCB
in NPAR mode.
v2:
- Dropped patch 10 "i40e: clean up PTP log messages" based on feedback
from David Laight and David Miller
- Split up the original patch 13 "i40e: AQ API updates for new commands"
into 2 patches (now #12 & #13) based on feedback from Or Gerlitz
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for ACPI to the amd-xgbe and amd-xgbe-phy drivers. This
support converts many of the device tree APIs to the new device_property
APIs.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The auto negotiation logic was geared to being the initiator of the
auto negotiation. This presented problems when auto negotiation was
initiated by the remote end. Change the auto negotiation logic to
make use of the auto negotiation event interrupt thus allowing the
auto negotiation state machine to function properly in either scenario.
This also removes the polling during auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the Tx ring cleanup can run at the same time that data is being
transmitted, a spin lock was used to protect the ring. This patch
eliminates the need for Tx spinlocks by updating the current ring
position only after all ownership bits for data being transmitted have
been set. This will insure that ring operations in the Tx cleanup path
do not interfere with the ring operations in the Tx transmit path.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the Rx descriptor ring processing similar to the Tx descriptor
ring processing. Remove the realloc_index and realloc_threshold
variables and base everything on the current index counter and the
dirty index counter.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When performing a device restart, like during an MTU change, sometimes
the device queues still have data and get hung up trying to flush
resulting in the device becoming unresponsive until brought down and
back up. To prevent this, always perform a device reset during a
restart.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The amd-xgbe driver relies on the amd-xgbe-phy phylib driver. Add a
check to be sure that if any errors occur during probing of the
amd-xgbe-phy driver then the amd-xgbe driver returns an error.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This set of patches resolves some checks reported by the checkpatch
tool.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bump i40e to 1.2.6 and i40evf to 1.2.0 version.
Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add parsing and reporting of iSCSI capability for a given device or
function.
Also add support for iSCSI partition type with DCB in NPAR mode.
In this mode it is expected that software would configure both the LAN
and iSCSI traffic classes for the iSCSI partition; whereas all the NIC
type partitions will use LAN TC (TC0) only.
Hence, the patch enables querying of DCB configuration in MFP mode and
configures TCs for iSCSI partition type.
Though NIC type partitions may not have more than 1 TC enabled for them
the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED
will be set/reset on all the partitions based on number of TCs on the
port. This is required as in DCB environment it is expected that all
traffic will be priority tagged.
Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Instead of leaving the Rx timestamps in the same mode as before if we
disable the Rx logic, we can set it into a mode that has the fewest
possible timestamps generated. To do this, select only V1 mode, but do
not enable UDP packet recognition. This should eliminate all (or at
least almost all) Rx timestamps, since V1 packets are always over UDP.
Change-ID: If847288e0030a716e059c4c33ab114f2cf038f05
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|