summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
2015-01-05be2net: support TX batching using skb->xmit_more flagSathya Perla
This patch uses skb->xmit_more flag to batch TX requests. TX is flushed either when xmit_more is false or there is no more space in the TXQ. Skyhawk-R and BEx chips require an even number of wrbs to be posted. So, when a batch of TX requests is accumulated, the last header wrb may need to be fixed with an extra dummy wrb. This patch refactors be_xmit() routine as a sequence of be_xmit_enqueue() and be_xmit_flush() calls. The Tx completion code is also updated to be able to unmap/free a batch of skbs rather than a single skb. Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-04qlcnic: Fix dump_skb outputJoe Perches
Use normal facilities to avoid printing each byte on a separate line. Now emits at KERN_DEBUG instead of KERN_INFO. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-04enic: reconfigure resources for kdump crash kernelGovindarajulu Varadarajan
When running in kdump kernel, reduce number of resources used by the driver. This will enable NIC to operate in low memory kdump kernel environment. Also change the driver version to .83 Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-04net: ethernet: cpsw: fix hangs with interruptsFelipe Balbi
The CPSW IP implements pulse-signaled interrupts. Due to that we must write a correct, pre-defined value to the CPDMA_MACEOIVECTOR register so the controller generates a pulse on the correct IRQ line to signal the End Of Interrupt. The way the driver is written today, all four IRQ lines are requested using the same IRQ handler and, because of that, we could fall into situations where a TX IRQ fires but we tell the controller that we ended an RX IRQ (or vice-versa). This situation triggers an IRQ storm on the reserved IRQ 127 of INTC which will in turn call ack_bad_irq() which will, then, print a ton of: unexpected IRQ trap at vector 00 In order to fix the problem, we are moving all calls to cpdma_ctlr_eoi() inside the IRQ handler and making sure we *always* write the correct value to the CPDMA_MACEOIVECTOR register. Note that the algorithm assumes that IRQ numbers and value-to-be-written-to-EOI are proportional, meaning that a write of value 0 would trigger an EOI pulse for the RX_THRESHOLD Interrupt and that's the IRQ number sitting in the 0-th index of our irqs_table array. This, however, is safe at least for current implementations of CPSW so we will refrain from making the check smarter (and, as a side-effect, slower) until we actually have a platform where IRQ lines are swapped. This patch has been tested for several days with AM335x- and AM437x-based platforms. AM57x was left out because there are still pending patches to enable ethernet in mainline for that platform. A read of the TRM confirms the statement on previous paragraph. Reported-by: Yegor Yefremov <yegorslists@googlemail.com> Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly) Cc: <stable@vger.kernel.org> # v3.9+ Signed-off-by: Felipe Balbi <balbi@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02mlx4: include clocksource.h againRichard Cochran
This driver uses the function, clocksource_khz2mult, and so it really must include clocksource.h. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02ixgbe: convert to CYCLECOUNTER_MASK macro.Richard Cochran
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02igb: convert to CYCLECOUNTER_MASK macro.Richard Cochran
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02e1000e: convert to CYCLECOUNTER_MASK macro.Richard Cochran
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02bnx2x: convert to CYCLECOUNTER_MASK macro.Richard Cochran
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02enic: free all rq buffs when allocation failsGovindarajulu Varadarajan
When allocation of all RQs fail, we do not free previously allocated buffers, before returning error. This causes memory leak. This patch fixes this by calling vnic_rq_clean(), which frees all the rq buffers. Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02net: ethernet: cisco: enic: enic_dev: Remove some unused functionsRickard Strandqvist
Removes some functions that are not used anywhere: enic_dev_enable2_done() enic_dev_enable2() enic_dev_deinit_done() enic_dev_init_prov2() enic_vnic_dev_deinit() This was partially found by using a static code analysis program called cppcheck. Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02net: ethernet: chelsio: cxgb3: mc5.c: Remove some unused functionsRickard Strandqvist
Removes some functions that are not used anywhere: dbgi_rd_rsp3() dbgi_wr_addr3() This was partially found by using a static code analysis program called cppcheck. Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02Altera TSE: Add missing phydevKostya Belezko
Altera network device doesn't come up after ifconfig eth0 down ifconfig eth0 up The reason behind is clearing priv->phydev during tse_shutdown(). The phydev is not restored back at tse_open(). Resubmiting as to follow Tobias Klauser suggestion. phy_start/phy_stop are called on each ifup/ifdown and phy_disconnect is called once during the module removal. Signed-off-by: Kostya Belezko <bkostya@hotmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02net/mlx4_core: Fix error flow in mlx4_init_hca()Jack Morgenstein
We shouldn't call UNMAP_FA here, this is done in mlx4_load_one. If mlx4_query_func fails, we need to invoke CLOSE_HCA for both native and master. Fixes: a0eacca948d2 ('net/mlx4_core: Refactor mlx4_load_one') Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02net/mlx4_core: Correcly update the mtt's offset in the MR re-reg flowMaor Gottlieb
Previously, mlx4_mt_rereg_write filled the MPT's entity_size with the old MTT's page shift, which could result in using an incorrect offset. Fix the initialization to be after we calculate the new MTT offset. In addition, assign mtt order to -1 after calling mlx4_mtt_cleanup. This is necessary in order to mark the MTT as invalid and avoid freeing it later. Fixes: e630664 ('mlx4_core: Add helper functions to support MR re-registration') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02net/fsl: remove hardcoded clock setting from xgmac_mdioShaohui Xie
There is no need to set the clock speed in read/write which will be performed unnecessarily for each mdio access. Init it during probe is enough. Also, the hardcoded clock value is not a proper way for all SoCs. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02net/fsl: remove irq assignment from xgmac_mdioShaohui Xie
Which is wrong and not used, so no extra space needed by mdiobus_alloc_size(), use mdiobus_alloc() instead. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-02net/fsl: remove reset from xgmac_mdioShaohui Xie
Since the reset is just clock setting, individual mdio reset is not available. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31qlcnic: Fix return value in qlcnic_probe()Yongjian Xu
If the check of adapter fails and goes into the 'else' branch, the return value 'err' should not still be zero. Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com> Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31net: axienet: fix error return codeJulia Lawall
Return a negative error code on failure. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier ret; expression e1,e2; @@ ( if (\(ret < 0\|ret != 0\)) { ... return ret; } | ret = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31net: sun4i-emac: fix error return codeJulia Lawall
Return a negative error code on failure. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier ret; expression e1,e2; @@ ( if (\(ret < 0\|ret != 0\)) { ... return ret; } | ret = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31myri10ge: fix error return codeJulia Lawall
Return a negative error code on failure. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier ret; expression e1,e2; @@ ( if (\(ret < 0\|ret != 0\)) { ... return ret; } | ret = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> The patch also modifies the test of mgp->cmd to satisfy checkpatch. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31net: Xilinx: fix error return codeJulia Lawall
Return a negative error code on failure. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier ret; expression e1,e2; @@ ( if (\(ret < 0\|ret != 0\)) { ... return ret; } | ret = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31GMAC: add driver for Rockchip RK3288 SoCs integrated GMACRoger Chen
This driver is based on stmmac driver. changes since v2: - use tab instead of space for macros - use HIWORD_UPDATE macro for GMAC_CLK_RX_DL_CFG and GMAC_CLK_TX_DL_CFG - remove drive-strength setting in the driver and set it in the pinctrl settings - use dev_err instead of pr_err - remove clock names's macros, just use the real name of the clock - use devm_clk_get() instead of clk_get() - remove clk_set_parent(bsp_priv->clk_mac, bsp_priv->clk_mac_pll) - remove gpio setting for LDO, just use regulator API - remove phy reset using gpio in the glue layer, it has been handled in the stmmac driver - remove handling phy interrupt (mii interrupt) changes since v1: - use BIT() to set register - combine two remap_write() operations into one for the same register - use macros for register value setting - remove grf fail check in rk_gmac_setup() and save all the check in set_rgmii_speed() - remove .tx_coe=1 in rk_gmac_data Signed-off-by: Roger Chen <roger.chen@rock-chips.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31i40e: Fix possible memory leak in i40e_dbg_dump_descJoe Perches
I didn't notice that return in the code, fix it by adding a goto out instead to free the memory. Fixes: > New smatch warnings: > drivers/net/ethernet/intel/i40e/i40e_debugfs.c:832 i40e_dbg_dump_desc() warn: possible memory leak of 'ring' Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Joe Perches <joe@perches.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-12-31igb_ptp: Include clocksource.h to get CLOCKSOURCE_MASK.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31e1000e: Include clocksource.h to get CLOCKSOURCE_MASK.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31igb: Remove unneeded FIXMETodd Fujinaka
Remove a FIXME comment that was missed in a commit on 1/2007. Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com> Reported-by: nick <xerofoify@gmail.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-12-31e100: fix typo in MDI/MDI-X eeprom check in e100_phy_initJohn W. Linville
Although it doesn't explicitly say so, commit 60ffa478759f39a2 ("e100: Fix MDIO/MDIO-X") appears to be intended to revert the earlier commit 648951451e6d2d53 ("e100: fixed e100 MDI/MDI-X issues"). However, careful examination reveals that the attempted revert actually _inverted_ the test for eeprom_mdix_enabled. That is bound to program a few PHYs incorrectly... https://bugzilla.redhat.com/show_bug.cgi?id=1156417 Signed-off-by: "John W. Linville" <linville@tuxdriver.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-12-31enic: add stats for dma mapping errorGovindarajulu Varadarajan
This patch adds generic statistics for enic. As of now dma_map_error is the only member. dma_map_erro is incremented every time dma maping error happens. Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31enic: check dma_mapping_errorGovindarajulu Varadarajan
This patch checks for pci_dma_mapping_error() after dma mapping the data. If the dma mapping fails we remove the previously queued frags and return NETDEV_TX_OK. Reported-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31enic: make vnic_wq_buf doubly linkedGovindarajulu Varadarajan
This patch makes vnic_wq_buf doubly liked list. This is needed for dma_mapping error check, in case some frag's dma map fails, we need to move back and remove previously queued buffers. Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-31net: fec: add Wake-on-LAN supportNimrod Andy
Support for Wake-on-LAN using Magic Packet. ENET IP supports sleep mode in low power status, when system enter suspend status, Magic packet can wake up system even if all SOC clocks are gate. The patch doing below things: - flagging the device as a wakeup source for the system, as well as its Wake-on-LAN interrupt - prepare the hardware for entering WoL mode - add standard ethtool WOL interface - enable the ENET interrupt to wake us Tested on i.MX6q/dl sabresd, sabreauto boards, i.MX6SX arm2 boards. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30net: gianfar: add missing __iomem annotationKevin Hao
Fix the following spare warning: drivers/net/ethernet/freescale/gianfar.c:3521:60: warning: incorrect type in argument 1 (different address spaces) drivers/net/ethernet/freescale/gianfar.c:3521:60: expected unsigned int [noderef] <asn:2>*addr drivers/net/ethernet/freescale/gianfar.c:3521:60: got unsigned int [usertype] *rfbptr drivers/net/ethernet/freescale/gianfar.c:205:16: warning: incorrect type in assignment (different address spaces) drivers/net/ethernet/freescale/gianfar.c:205:16: expected unsigned int [usertype] *rfbptr drivers/net/ethernet/freescale/gianfar.c:205:16: got unsigned int [noderef] <asn:2>*<noident> drivers/net/ethernet/freescale/gianfar.c:2918:44: warning: incorrect type in argument 1 (different address spaces) drivers/net/ethernet/freescale/gianfar.c:2918:44: expected unsigned int [noderef] <asn:2>*addr drivers/net/ethernet/freescale/gianfar.c:2918:44: got unsigned int [usertype] *rfbptr Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30net: gianfar: mark the local functions staticKevin Hao
Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30net: sxgbe: Use setup_timerJulia Lawall
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.function = f; -t.data = d; // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30ksz884x: Use setup_timerJulia Lawall
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.function = f; -t.data = d; // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30atl1e: Use setup_timerJulia Lawall
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.function = f; -t.data = d; // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30atheros: atlx: Use setup_timerJulia Lawall
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.function = f; -t.data = d; // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30timecounter: keep track of accumulated fractional nanosecondsRichard Cochran
The current timecounter implementation will drop a variable amount of resolution, depending on the magnitude of the time delta. In other words, reading the clock too often or too close to a time stamp conversion will introduce errors into the time values. This patch fixes the issue by introducing a fractional nanosecond field that accumulates the low order bits. Reported-by: Janusz Użycki <j.uzycki@elproma.com.pl> Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30net: cpts: convert to timecounter adjtime.Richard Cochran
This patch changes the driver to use the new and improved method for adjusting the offset of a timecounter. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30net: mlx4: convert to timecounter adjtime.Richard Cochran
This patch changes the driver to use the new and improved method for adjusting the offset of a timecounter. Compile tested only. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30net: ixgbe: convert to timecounter adjtime.Richard Cochran
This patch changes the driver to use the new and improved method for adjusting the offset of a timecounter. Compile tested only. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30net: igb: convert to timecounter adjtime.Richard Cochran
This patch changes the driver to use the new and improved method for adjusting the offset of a timecounter. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30net: e1000e: convert to timecounter adjtime.Richard Cochran
This patch changes the driver to use the new and improved method for adjusting the offset of a timecounter. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30net: fec: convert to timecounter adjtime.Richard Cochran
This patch changes the driver to use the new and improved method for adjusting the offset of a timecounter. Compile tested only. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30net: bnx2x: convert to timecounter adjtime.Richard Cochran
This patch changes the driver to use the new and improved method for adjusting the offset of a timecounter. Compile tested only. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30net: xgbe: convert to timecounter adjtime.Richard Cochran
This patch changes the driver to use the new and improved method for adjusting the offset of a timecounter. Compile tested only. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-30time: move the timecounter/cyclecounter code into its own file.Richard Cochran
The timecounter code has almost nothing to do with the clocksource code. Let it live in its own file. This will help isolate the timecounter users from the clocksource users in the source tree. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-12-27ne2k-pci: Add pci_disable_device in error handlingJia-Ju Bai
For linux-3.18.0 The driver lacks pci_disable_device in error handling code of ne2k_pci_init_one, so the device enabled by pci_enable_device is not disabled when errors occur. This patch fixes this problem. Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com> Signed-off-by: David S. Miller <davem@davemloft.net>