| Age | Commit message (Collapse) | Author |
|---|
|
This is very simple driver for SuperH Mobile IrDA
which support SIR/MIR/FIR.
This patch add only SIR support for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is very simple IrDA SIR driver for SuperH.
This driver was tested by irdaping/ircp on SH7724 EcoVec24 board
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Graff Yang <graff.yang@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
This patch removes IrPORT and the old dongle drivers (all off them
have replacement drivers).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This dongle does not follow the usb-irda specification, so it needs its own
special driver. First, it uses control URBs for data transfer, instead of
bulk or interrupt transfers; the only interrupt endpoint exposed seems to
be a dummy to prevent the interface from being rejected. Second, it uses
obfuscation and padding at the USB traffic level, for no apparent reason
other than to make reverse engineering harder (full details on obfuscation
in comments at beginning of source). Although it is advertised as a "4 Mbps
FIR dongle", it apparently loses packets at speeds greater than 57600 bps.
On plugin, this dongle reports vendor and device IDs: 0x07d0:0x4959 .
The Windows driver that is used normally to control this dongle has a
filename of KS-959.SYS .
Signed-off-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This dongle does not follow the usb-irda specification, so it needs its own
special driver. Just like the Kingsun/Donshine dongle, it exposes two
interrupt endpoints. Reception is performed through direct reads from the
input endpoint. Transmission requires splitting the IrDA frames into 8-byte
segments, in which the first byte encodes how many of the remaining 7 bytes
are used as data. Speed change is made with a control URB just like the one
in cypress_m8, and it seems to support up to 115200 bps.
On plugin, this dongle reports vendor and device IDs: 0x07d0:0x4100
Signed-off-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EP7211 SIR driver was the only one left without a new SIR API port.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This dongle does not follow the usb-irda specification, so it needs its
own special driver. In addition, it uses interrupt endpoints instead of
bulk ones as the rest of USB IrDA dongles supported by Linux (just to be
different?) and data reads need to be parsed to extract the valid bytes
before being unwrapped (details in the comment at the start of the
source). No speed commands have been discovered for this dongle, and I
suspect it does not have any at all.
On plugin, this dongle reports vendor and device IDs: 0x07c0:0x4200 .
The Windows driver that is used normally to control this dongle has a
filename of DSIR620.SYS .
Signed-off-by: Alex Villac�s Lasso <a_villacis@palosanto.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MosChip MCS7780 chipset is an IrDA USB bridge that
doesn't conform with the IrDA-USB standard and thus needs
its separate driver.
Tested on an actual MCS7780 based dongle.
Original implementation by Brian Pugh <bpugh@cs.pdx.edu>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since sir_kthread.c pretty much duplicates the workqueue
functionality, we'd better switch. The SIR fsm has been merged into
sir_dev.c and thus sir_kthread.c is deleted.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here goes a patch for supporting TOIM3232 based serial IrDA dongles.
The code is based on the tekram dongle code.
It's been tested with a TOIM3232 based IRWave 320S dongle. It may work
for TOIM4232 dongles, although it's not been tested.
Signed-off-by: David Basden <davidb-irda@rcpt.to>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EXPORT_SYMBOL's do nowadays belong to the files where the actual
functions are.
Moving the module_init/module_exit to the file with the actual functions
has the advantage of saving a few bytes due to the removal of two
functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch from Nicolas Pitre
This is the PXA2xx common IRDA driver, plus platform support
for Lubbock and Mainstone.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
