| Age | Commit message (Collapse) | Author |
|---|
|
Implemented ixgbe_ndo_set_vf_bw function which is being used by iproute2
tool. In addition, updated ixgbe_ndo_get_vf_config function to show the
actual rate limit to the user.
The rate limitation can be configured only when the link is up and the
link speed is 10Gb.
The rate limit value can be 0 or ranged between 11 and actual link
speed measured in Mbps. A value of '0' disables the rate limit for
this specific VF.
iproute2 usage will be 'ip link set ethX vf Y rate Z'.
After the command is made, the rate will be changed instantly.
To view the current rate limit, use 'ip link show ethX'.
The rates will be zeroed only upon driver reload or a link speed change.
This feature is being supported by 82599 and X540 devices.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This enables multiple {Tx|Rx} rings per traffic class while in DCB
mode. In order to get this working as expected the tc_to_tx net
device mapping is configured as well as the prio_tc_map.
skb priorities are mapped across a range of queue pairs to get
a distribution per traffic class. The maximum number of
queue pairs used while in DCB mode is capped at 64. The hardware
max is actually 128 queues but 64 is sufficient for now and
allocating more seemed a bit excessive. It is easy enough to
increase the cap later if need be.
To get the 802.1Q priority tags inserted correctly ixgbe was
previously using the skb queue_mapping field to directly set
the 802.1Q priority. This no longer works because we have removed
the 1:1 mapping between queues and traffic class. Each ring
is aligned with an 802.1Qaz traffic class so here we add an
extra field to the ring struct to identify the 802.1Q traffic
class. This uses an extra byte of the ixgbe_ring struct
fortunately there was a 2byte hole,
struct ixgbe_ring {
void * desc; /* 0 8 */
struct device * dev; /* 8 8 */
struct net_device * netdev; /* 16 8 */
union {
struct ixgbe_tx_buffer * tx_buffer_info; /* 8 */
struct ixgbe_rx_buffer * rx_buffer_info; /* 8 */
}; /* 24 8 */
long unsigned int state; /* 32 8 */
u8 atr_sample_rate; /* 40 1 */
u8 atr_count; /* 41 1 */
u16 count; /* 42 2 */
u16 rx_buf_len; /* 44 2 */
u16 next_to_use; /* 46 2 */
u16 next_to_clean; /* 48 2 */
u8 queue_index; /* 50 1 */
u8 reg_idx; /* 51 1 */
u16 work_limit; /* 52 2 */
/* XXX 2 bytes hole, try to pack */
u8 * tail; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
Now we can set the VLAN priority directly and it will be
correct. User space can indicate the 802.1Qaz priority
using the SO_PRIORITY setsocket() option and QOS layer will
steer the skb to the correct rings. Additionally using
the multiq qdisc with a queue_mapping action works as
well.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This implements dcbnl get and set capabilities ops. The
devices supported by ixgbe can be configured to run in
IEEE or CEE modes but not both.
With the DCBX set capabilities bit we add an explicit
signal that must be used to toggle between these modes.
This patch adds logic to fail the CEE command set_hw_all()
which programs the device with a CEE configuration if
the CEE caps bit is not set. Similarly, IEEE set
commands will fail if the IEEE caps bit is not set. We
allow most CEE config set commands to occur because they
do not touch the hardware until set_hw_all() is called.
The one exception to the above is the {set|get}app routines.
These must always be protected by caps bits to ensure
side effects do not corrupt the current configured mode.
By requiring the caps bit to be set correctly we can
maintain a consistent configuration in the hardware
for CEE or IEEE modes and prevent partial hardware
configurations that may occur if user space does
not send a complete IEEE or CEE configurations.
It is expected that user space will signal a DCBX mode
before programming device.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add support to the ndo_fcoe_ddp_target() to allow the Intel 82599 device to
also provide DDP offload capability when the upper FCoE protocol stack is
operating as a target.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Updating the copyrights for 2011 as well as make the ixgbe_copyright string
a constant.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We didn't need the prototype and it was causing namespace complaints so
I made it static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Implements 802.1Qaz support for ixgbe driver. Additionally,
this adds IEEE_8021QAZ_TSA_{} defines to dcbnl.h this is to
avoid having to use cryptic numeric codes for the TSA type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change fixes several issues found in ntuple filtering while I was
doing the ATR refactor.
Specifically I updated the masks to work correctly with the latest version
of ethtool, I cleaned up the exception handling and added detailed error
output when a filter is rejected, and corrected several bits that were set
incorrectly in ixgbe_type.h.
The previous version of this patch included a printk that was left over from
me fixing the filter setup. This patch does not include that printk.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds a compressed input type for atr signature hash
computation. It also drops the use of the set functions when setting up
the ATR input since we can then directly setup the hash input as two dwords
that can be stored and passed as registers.
With these changes the cost of computing the has is low enough that we can
perform a hash computation on each TCP SYN flagged packet allowing us to
drop the number of flow director misses considerably in tests such as
netperf TCP_CRR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change cleans up the layout of the flow director data, and the
algorithm used to calculate the hash resulting in a 35x / 3500% performance
increase versus the old flow director hash computation. The overall effect
is only a 1% increase in transactions per second though due to the fact
that only 1 packet in 20 are actually hashed upon.
TCP_RR before:
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 60.00 23059.27
16384 87380
TCP_RR after:
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 60.00 23239.98
16384 87380
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When disable the Rx logic globally, we would also want to disable the per Rx
queue receive logic by per queue Rx control register RXDCTL so no more DMA is
happening from the packet buffer to the receive buffer associated with the Rx
ring, before we start unmapping Rx ring receive buffer. The hardware may take
max of 100us before the corresponding Rx queue is really disabled. Added
ixgbe_disable_rx_queue() for this purpose.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the x540 MAC which is the next MAC in the
82598/82599 line.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Adds the new x540.c file and Aquantia 1202 PHY for X540 support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The Tx hang logic has been known to detect false hangs when
the device is receiving pause frames or has delayed processing
for some other reason.
This patch makes the logic more robust and resolves these
known issues. The old logic checked to see if the device
was paused by querying the HW then the hang logic was
aborted if the device was currently paused. This check was
racy because the device could have been in the pause state
any time up to this check. The other operation of the
hang logic is to verify the Tx ring is still advancing
the old logic checked the EOP timestamp. This is not
sufficient to determine the ring is not advancing but
only infers that it may be moving slowly.
Here we add logic to track the number of completed Tx
descriptors and use the adapter stats to check if any
pause frames have been received since the previous Tx
hang check. This way we avoid racing with the HW
register and do not detect false hangs if the ring is
advancing slowly.
This patch is primarily the work of Jesse Brandeburg. I
clean it up some and fixed the PFC checking.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change cleans up some of the items in ixgbe_map_rings_to_vectors.
Specifically it merges the two for loops and drops the unnecessary vectors
parameter.
It also moves the vector names into the q_vectors themselves.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change cleans up the use of rsc_count and changes it to a boolean since
the actual numerical value is used nowhere in the Rx cleanup path. I am
also moving the skb count into the RSC_CB path since it is much easier to
track it there than when it is passed as a parameter to various function
calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change adds a set of state flags to the rings that allow them to
independently function allowing for features like RSC, packet split, and
TX hang detection to be done per ring instead of for the entire device.
This is accomplished by re-purposing the flow director reinit_state member
and making it a global state instead since a long for a single bit flag is
a bit wasteful.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This is the start of work to sort out what belongs in the rings and what
belongs in the q_vector. Items like the CPU variable for make much more
sense in the q_vector since the CPU is a per-interrupt thing rather than a
per ring thing.
I also added a back-pointer from the ring to the q_vector.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change places a netdev pointer directly into the ring structure. This
way we can avoid having to determine which netdev we are supposed to be
using and can just access the one on the ring directly.
As a result of this change further collapse of the code is possible by
dropping the adapter from ixgbe_alloc_rx_buffers, and the netdev pointer
from ixgbe_xmit_frame_ring_adv and ixgbe_maybe_stop_tx.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change moved some of the RX and TX stats into separate structures and
them placed those structures in a union in order to help reduce the size of
the ring structure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change is meant to simplify DMA map/unmap by providing a device
pointer. As a result the adapter pointer can be dropped from many of
the calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change drops ring->head since it is not used in any hot-path and can
easily be determined using IXGBE_[RT]DH(ring->reg_idx).
It also changes ring->tail into a true pointer so we can avoid unnecessary
pointer math to find the location of the tail.
In addition I also dropped the setting of head and tail in
ixgbe_clean_[rx|tx]_ring. The only location that should be setting the head
and tail values is ixgbe_configure_[rx|tx]_ring and that is only while the
queue is disabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change re-orders alloc_rx_buffers to make better use of the packet
split enabled flag. The new setup should require less branching in the
code since now we are down to fewer if statements since we either are
handling packet split or aren't.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change simplifies the work being done by the TX interrupt handler and
pushes it into the tx_map call. This allows for fewer cache misses since
the TX cleanup now accesses almost none of the skb members.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the high and low water marks for PFC are being set
conservatively for jumbo frames. This means the RX buffers
are being underutilized in the default 1500 MTU. This patch
fixes this so that the water marks are set as described in
the data sheet considering the MTU size.
The equation used is,
RTT * 1.44 + MTU * 1.44 + MTU
Where RTT is the round trip time and MTU is the max frame size
in KB. To avoid floating point arithmetic FC_HIGH_WATER is
defined
((((RTT + MTU) * 144) + 99) / 100) + MTU
This changes how the hardware field fc.low_water and
fc.high_water are used. With this change they are no longer
storing the actual low water and high water markers but are
storing the required head room in the buffer. This simplifies
the logic and we do not need to account for the size of the
buffer when setting the thresholds.
Testing with iperf and 16 threads showed a slight uptick in
throughput over a single traffic class .1-.2Gbps and a reduction
in pause frames. Without the patch a 30 second run would show
~10-15 pause frames being transmitted with the patch ~2-5 are
seen. Test were run back to back with 82599.
Note RXPBSIZE is in KB and low and high water marks fields are
also in KB. However the FCRT* registers are 32B granularity and
right shifted 5 into the register,
(((rx_pbsize - water_mark) * 1024) / 32) << 5
is the most explicit conversion here we simplify
(rx_pbsize - water_mark) * 32 << 5 = (rx_pbsize - water_mark) << 10
This patch updates the PFC thresholds and legacy FC thresholds.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
"cat /proc/net/dev" uses RCU protection only.
Its quite possible we call a driver get_stats() method while device is
dismantling and freeing its data structures.
So get_stats() methods must be very careful not accessing driver private
data without appropriate locking.
In ixgbe case, we access rx_ring pointers. These pointers are freed in
ixgbe_clear_interrupt_scheme() and set to NULL, this can trigger NULL
dereference in ixgbe_get_stats64()
A possible fix is to use RCU locking in ixgbe_get_stats64() and defer
rx_ring freeing after a grace period in ixgbe_clear_interrupt_scheme()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Tantilov, Emil S <emil.s.tantilov@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Current ixgbe stats have following problems :
- Not 64 bit safe (on 32bit arches)
- Not safe in ixgbe_clean_rx_irq() :
All cpus dirty a common location (netdev->stats.rx_bytes &
netdev->stats.rx_packets) without proper synchronization.
This slow down a bit multiqueue operations, and possibly miss some
updates.
Fixes :
Implement ndo_get_stats64() method to provide accurate 64bit rx|tx
bytes/packets counters, using 64bit safe infrastructure.
ixgbe_get_ethtool_stats() also use this infrastructure to provide 64bit
safe counters.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the ixgbe driver use the new vlan accleration model.
Signed-off-by: Jesse Gross <jesse@nicira.com>
CC: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new infrastructure to balance interrupts for flow
alignment when ATR or Flow Director are enabled.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change makes it so that the ethtool loopback test uses the standard
ring configuration and allocation functions. As a result the loopback test
will be much more effective at testing core driver functionality.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All of the DESC_ADV macros are currently needing the pointers to be
de-referenced before accessing the ring. Instead of having to add all of
the asterisks it is easier to just update the macro to expect a pointer to
the ring.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bump the header size for packet split to 512 bytes since this makes the
best use of the 1k buffer that is allocated for any skb 512 bytes or
smaller.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change corrects issues where macvlan was not correctly triggering
promiscuous mode on ixgbe due to the filters not being correctly set. It
also corrects the fact that VF rar filters were being overwritten when the
PF was reset.
CC: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is alternative to a previous patch submitted by Joe Perches.
Create common macros e_<level> and e_dev_<level> that use netdev_<level> and
dev_<level> similar to e1000e.
Redefined pr_fmt for driver messages.
Use %pM to display MAC address.
Aligned text to better match the new format.
CC: Joe Perches <joe@perches.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for a new copper device for 82599, device id 0x151c.
This 82599 10GBase-T device uses the PHY's internal temperature sensor
to guard against over-temp conditions. In this scenario the PHY will be
put in a low power mode and link will no longer be able to transmit or
receive any data. When this occurs, the over-temp interrupt is latched
and driver logs this error message. A HW reset or power cycle is
required to clear this status.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the "ip link set" and "ip link show" commands that allow
configuration of the virtual functions' MAC and port VLAN via user space
command line.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit d5ffd75a27fade39ba5df3b07290c5a2c297b9bd.
As requested by Jeff Kircher.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to an errata in 82598 parts MSI-X needs to be disabled
in certain ixgbe devices designed to transfer peer-to-peer
traffic on the PCIe bus. This patch sets the default
interrupt type to MSI rather than MSI-X for specific Cisco
ixgbe adapters.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Acked-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the last patch I missed an unecessary min_t comparison.
This patch removes it, the path allocates at most
72 tx queues for 82599 and 24 for 82598 there is no need
for this check.
Additionally this sets MAX_[TX|RX]_QUEUES to 72. Which is
used as the size for the tx/rx_ring arrays. There is no
reason to have more tx_rings/rx_rings then num_tx_queues.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds n-tuple filter programming to 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allocates the ring structures themselves on each
NUMA node along with the buffer_info structures. This way we
don't allocate the entire ring memory on a single node in one
big block, thus reducing NUMA node memory crosstalk.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default policy for the current driver is to do all its memory
allocation on whatever processor is running insmod/modprobe. This
is less than optimal.
This driver's default mode of operation will be to use each node for each
subsequent transmit/receive queue. The most efficient allocation will be
to then have the interrupts bound in such a way as to match up the
interrupt of the queue to the cpu where its memory was allocated.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Processing multiple ixgbe_watchdog_task calls may cause
the link_up variable and IXGBE_FLAG_NEED_LINK_UPDATE flag
to be set incorrectly. In the worse case this is causing
the netif_carrier_off to be called inappropriately which
results in an interface that can't be brought up.
Although schedule_work() will only schedule the task if
it is not already on the work queue the WORK_STRUCT_PENDING
bits are cleared just before calling the work function.
This allows WORK_STRUCT_PENDING to be cleared, the work
function to start and meanwhile schedule another task.
This patch adds a mutex to the watchdog task. This bug is
actualized by changing DCB settings or doing extended
cable pull or reset tests.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This data storage for SW emulated MAC addresses is unlikely to ever be used
so pull it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds register definitions, bit definitions and structures used by
the driver to support SR-IOV features of the 82599 controller.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drop variables that had cache lines modified in simultaneous hot paths.
keep some variables modified on hot paths but make their storage per queue.
cache align DMA data buffer start addresses.
cache align (padding) some structures that end within a cacheline.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
decrease the memory utilization of the tx / rx queue allocation
by changing the default ring size to 512 (from 1024). At
1024 rx entries of 2KB each (from 4kB slab) with 16 queues
ixgbe was using 64 MB of memory per port, which is not
necessary.
Users can still change queue lengths with ethtool -k.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes skb_dma_map/unmap calls from the ixgbe driver due to the
fact that the calls don't work with HW IOMMU enabled systems. The problem
is that multiple mappings will give different results when HW IOMMU is
enabled and the skb_dma_map/unmap calls only have one location to store
mappings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
