| Age | Commit message (Collapse) | Author |
|---|
|
Updating the copyrights for 2011 as well as make the ixgbe_copyright string
a constant.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The X540 devices grabs semaphores differently than 82599 and 82598
devices do. They do however also grab them in allot of the same
functions. So I'm adding a new MAC operation function pointer to
allow us to use the correct function based on our MAC type. I'm also
changing all the semaphore calls to use this new function pointer.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Clean up commented out include file and use #define instead of hard coded
value for number of RAR entries.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The I2C interface was not being correctly locked down per port. As such
this can lead to race conditions that can cause issues. This patch cleans
up the handling to make certain we are not experiencing racy I2C access.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We were reading the address after it had been initialized and this results
in the permanent address on the system being changed. This change corrects
that by storing the address before we re-initialize it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch contains a number of whitespace and formatting cleanups.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch specifically checks for 100 Full link speed instead of
assuming we are linked at 100 if not linked at 10G and 1G.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change removes the unused code that was setting up the uc_addr_list.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change modifies the ixgbe drivers so that it will not drop the
multicast filters while updating them. Instead it uses an intermediate
table to store the filter and then writes that filter to the hardware.
Based on original patch from Dave Boutcher <daveboutcher@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Dave Boutcher <daveboutcher@gmail.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The X540 PHY reset pointer isn't currently used which is a good thing as it
wouldn't work as implemented. On top of that the X540 firmware is written
with the assumption that is does not need to be reset for proper
initialization so it's not needed. I'm just assigning the pointer at NULL
as the current implementation is rather misleading.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so that out of bounds requests to these calls will
now return IXGBE_ERR_INVALID_ARGUMENT instead of returning 0.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fills in the values for bus speed and width of the
ixgbe_bus_speed and ixgbe_bus_width enums.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Some PHYs require that we poll the reset bit and wait for it to clear
before continuing initialization. As such we should add this check to the
end of the ixgbe_reset_phy_generic routine.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently check link reports the link state as down, if at any time
the link had previously gone down since the last time the LINKS
register was read. This does not accurately reflect the function of
the check link call, which should be to return the CURRENT link
state. Code now reads the LINKS registers twice, once to clear the
previous and again to get the current value.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change cleans up several issues in ixgbe_identify_sfp_module_generic
including whitespace, redundant code, I2C EEPROM reads without exception
handling, and an if/elseif/else without braces.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Double resets are required for recovery from certain error conditions.
Between resets, it is necessary to stall to allow time for any pending HW
events to complete. We use 1usec since that is what is needed for
ixgbe_disable_pcie_master(). The second reset then clears out any effects
of those events.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The media type was not being set for the 82599 T3 LAN on motherboard. This
change corrects that.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We were incorrectly freeing IRQs that we had not requested. This change
corrects that by making certain we only free q_vectors that we have
requested IRQs for.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change cleans up much of the logic related to the hardware semaphores
on the adapters. There were a number of issues with timings that needed to
be addressed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change just cleans up a few defines in ixgbe_type.h related to wake on LAN.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The X540 controller supports jumbo frames in SR-IOV mode. Allow
configuration of jumbo frames either in the PF driver or on behalf of
a VF.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
Documentation/feature-removal-schedule.txt
drivers/net/e1000e/netdev.c
net/xfrm/xfrm_policy.c
|
|
A HW limitation was recently discovered where the last buffer in a DDP offload
cannot be a full buffer size in length. Fix the issue with a work around by
adding another buffer with size = 1.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Systems containing an 82599EB and running a backported driver from
upstream were panicing on boot. It turns out hw->mac.ops.setup_sfp is
only set for 82599, so one should check to be sure that pointer is set
before continuing in ixgbe_sfp_config_module_task. I verified by
inspection that the upstream driver has the same issue and also added a
check before the call in ixgbe_sfp_link_config.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Current driver does not show 100MB support in ethtool.
Adding support for the same.
Signed-off-by: Atita Shirwaikar <atita.shirwaikar@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The function ixgbe_init_mbx_params_pf isn't used unless CONFIG_PCI_IOV
is defined. This is causing namespace warnings. So I wrapped its
definition in CONFIG_PCI_IOV too.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We had a support function that just walked a few pointers to get
from the ixgbe_hw struct to the netdev pointer. This was causing
a namespace warning so I removed it and just reference the pointers
directly.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We didn't need the prototype and it was causing namespace complaints so
I made it static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This consolidates hardware specifics to ixgbe_dcb.c this simplifies
code that was previously branching based on hardware type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This removes the RESET bit previously used to force a device
reset when DCB bandwidth configurations were changed. This can
now be done dynamically without a reset so the bit is no longer
needed. The only remaining operations that force a device reset
are DCB enable/disable and FCoE application priority changes.
DCB enable/disable is a hardware requirement.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The 82599 and 82598 devices do not require hardware resets to
configure CEE pg settings. This patch changes DCB configuration
to set the CEE pg values directly from the dcbnl ops routine.
This reduces the number of resets seen on the wire and allows
LLDP to reach a steady state faster.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Implements 802.1Qaz support for ixgbe driver. Additionally,
this adds IEEE_8021QAZ_TSA_{} defines to dcbnl.h this is to
avoid having to use cryptic numeric codes for the TSA type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the routines that configure the HW for DCB require a
ixgbe_dcb_config structure. This structure was designed to support
the CEE standard and does not match the IEEE standard well.
This patch changes the HW routines in ixgbe_dcb_8259x.{ch} to use
raw pfc and bandwidth values. This requires some parsing of the DCB
configuration but makes the HW routines independent of the data
structure that contains the DCB configuration.
The primary advantage to doing this is we can do HW setup directly
from the 802.1Qaz ops without having to arbitrarily encapsulate this
data into the CEE structure.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove round robin configuration code for 82598 parts it
is not settable and is always false.
If we need/want this in the future we can add it back properly.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the FCoE priority is not changing do not set the RESET and
APP_UPCHG bits. This causes unneeded HW resets and which can
cause unneeded LLDP frames and negotiations.
The current check is not sufficient because the FCoE priority
can change twice during a negotiation which results in the
bits being set. This occurs when the switch changes the
priority or when the link is reset with switches that do not
include the APP priority until after PFC has been negotiated.
This results in set_app being called with the local APP
priority. Then the negotiation completes and set_app
is called again with the peer APP priority. The check
fails so the device is reset and the above occurs again
resulting in an endless loop of resets.
By only resetting the device if the APP priority has really
changed we short circuit the loop.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This will synchronize the version string with that of the latest source
forge driver which shares its functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The ixgbe_fcoe_ddp_get function wasn't initializing one of its variables
and this was producing compiler warnings. This patch cleans that up.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change fixes VM pool allocation issues based on MAC address filtering,
as well as limits the scope of VF access to promiscuous mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We have found a hardware erratum on 82599 hardware that can lead to
unpredictable behavior when Header Splitting mode is enabled. So
we are no longer enabling this feature on affected hardware.
Please see the 82599 Specification Update for more information.
CC: stable@kernel.org
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Caught with gcc 4.6 -Wunused-but-set-variable
Remove unused napi_vectors variable.
Fix the use of reset_bit in ixgbe_reset_hw_X540()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
|
|
After recent changes, (percpu stats on vlan/tunnels...), we dont need
anymore per struct netdev_queue tx_bytes/tx_packets/tx_dropped counters.
Only remaining users are ixgbe, sch_teql, gianfar & macvlan :
1) ixgbe can be converted to use existing tx_ring counters.
2) macvlan incremented txq->tx_dropped, it can use the
dev->stats.tx_dropped counter.
3) sch_teql : almost revert ab35cd4b8f42 (Use net_device internal stats)
Now we have ndo_get_stats64(), use it, even for "unsigned long"
fields (No need to bring back a struct net_device_stats)
4) gianfar adds a stats structure per tx queue to hold
tx_bytes/tx_packets
This removes a lockdep warning (and possible lockup) in rndis gadget,
calling dev_get_stats() from hard IRQ context.
Ref: http://www.spinics.net/lists/netdev/msg149202.html
Reported-by: Neil Jones <neiljay@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
Documentation/trace/events.txt: Remove obsolete sched_signal_send.
writeback: fix global_dirty_limits comment runtime -> real-time
ppc: fix comment typo singal -> signal
drivers: fix comment typo diable -> disable.
m68k: fix comment typo diable -> disable.
wireless: comment typo fix diable -> disable.
media: comment typo fix diable -> disable.
remove doc for obsolete dynamic-printk kernel-parameter
remove extraneous 'is' from Documentation/iostats.txt
Fix spelling milisec -> ms in snd_ps3 module parameter description
Fix spelling mistakes in comments
Revert conflicting V4L changes
i7core_edac: fix typos in comments
mm/rmap.c: fix comment
sound, ca0106: Fix assignment to 'channel'.
hrtimer: fix a typo in comment
init/Kconfig: fix typo
anon_inodes: fix wrong function name in comment
fix comment typos concerning "consistent"
poll: fix a typo in comment
...
Fix up trivial conflicts in:
- drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
- fs/ext4/ext4.h
Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
|
|
This change fixes several issues found in ntuple filtering while I was
doing the ATR refactor.
Specifically I updated the masks to work correctly with the latest version
of ethtool, I cleaned up the exception handling and added detailed error
output when a filter is rejected, and corrected several bits that were set
incorrectly in ixgbe_type.h.
The previous version of this patch included a printk that was left over from
me fixing the filter setup. This patch does not include that printk.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds a compressed input type for atr signature hash
computation. It also drops the use of the set functions when setting up
the ATR input since we can then directly setup the hash input as two dwords
that can be stored and passed as registers.
With these changes the cost of computing the has is low enough that we can
perform a hash computation on each TCP SYN flagged packet allowing us to
drop the number of flow director misses considerably in tests such as
netperf TCP_CRR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change cleans up the layout of the flow director data, and the
algorithm used to calculate the hash resulting in a 35x / 3500% performance
increase versus the old flow director hash computation. The overall effect
is only a 1% increase in transactions per second though due to the fact
that only 1 packet in 20 are actually hashed upon.
TCP_RR before:
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 60.00 23059.27
16384 87380
TCP_RR after:
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 60.00 23239.98
16384 87380
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When disable the Rx logic globally, we would also want to disable the per Rx
queue receive logic by per queue Rx control register RXDCTL so no more DMA is
happening from the packet buffer to the receive buffer associated with the Rx
ring, before we start unmapping Rx ring receive buffer. The hardware may take
max of 100us before the corresponding Rx queue is really disabled. Added
ixgbe_disable_rx_queue() for this purpose.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the anti-spoofing feature in the HW. Packets from
VF devices with spoofed MAC addresses or VLAN tags will be blocked
and a counter incremented. During the watchdog timer the spoofed
packet dropped counter is read and if it is non-zero then a warning
message is displayed on the host VMM's console.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add X540 specific feature support to X540
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Print warnings to the system log when the VF attempts to override
MAC/VLAN settings that were configured by the VMM Host administrator
using the ip link set commands.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
