summaryrefslogtreecommitdiffstats
path: root/drivers/net/mlx4/mr.c
AgeCommit message (Collapse)Author
2008-05-05mlx4_core: Support creation of FMRs with pages smaller than 4KOren Duer
Don't hard code a test against a minimum page shift of 12, since the device may support smaller pages. Test against the actual smallest page size from the device capabilities. Signed-off-by: Oren Duer <oren@mellanox.co.il> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-29mlx4_core: Avoid recycling old FMR R_Keys too soonOlaf Kirch
When a FMR is unmapped, mlx4 resets the map count to 0, and clears the upper part of the R_Key which is used as the sequence counter. This poses a problem for RDS, which uses ib_fmr_unmap as a fence operation. RDS assumes that after issuing an unmap, the old R_Keys will be invalid for a "reasonable" period of time. For instance, Oracle processes uses shared memory buffers allocated from a pool of buffers. When a process dies, we want to reclaim these buffers -- but we must make sure there are no pending RDMA operations to/from those buffers. The only way to achieve that is by using unmap and sync the TPT. However, when the sequence count is reset on unmap, there is a high likelihood that a new mapping will be given the same R_Key that was issued a few milliseconds ago. To prevent this, don't reset the sequence count when unmapping a FMR. Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-02-14mlx4_core: Move table_find from fmr_alloc to fmr_enableJack Morgenstein
mlx4_table_find (for FMR MPTs) requires that ICM memory already be mapped. Before this fix, FMR allocation depended on ICM memory already being mapped for the MPT entry. If all currently mapped entries are taken, the find operation fails (even if the MPT ICM table still had more entries, which were just not mapped yet). This fix moves the mpt find operation to fmr_enable, to guarantee that any required ICM memory mapping has already occurred. Found by Oren Duer of Mellanox. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-02-06mlx4_core: Clean up struct mlx4_bufRoland Dreier
Now that struct mlx4_buf.u is a struct instead of a union because of the vmap() changes, there's no point in having a struct at all. So move .direct and .page_list directly into struct mlx4_buf and get rid of a bunch of unnecessary ".u"s. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-02-04mlx4_core: Fix more section mismatchesRoland Dreier
Commit 3d73c288 ("mlx4_core: Fix section mismatches") fixed some of the section mismatches introduced when error recovery was added, but there were still more cases of errory recovery code calling into __devinit code from regular .text. Fix this by getting rid of the now-incorrect __devinit annotations. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-10mlx4_core: Fix section mismatchesRoland Dreier
Commit ee49bd93 ("mlx4_core: Reset device when internal error is detected") introduced some section mismatch problems when CONFIG_HOTPLUG=n, because the error recovery code tears down and reinitializes the device after everything is loaded, which ends up calling into lots of code marked __devinit and __devexit from regular .text. Fix this by getting rid of these now-incorrect section markers. Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09IB/mlx4: Implement FMRsJack Morgenstein
Implement FMRs for mlx4. This is an adaptation of code from mthca. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09mlx4_core: Write MTTs from CPU instead with of WRITE_MTT FW commandJack Morgenstein
Write MTT entries directly to ICM from the driver (eliminating use of WRITE_MTT command). This reduces the number of FW commands needed to register an MR by at least a factor of 2 and speeds up memory registration significantly. This code will also be used to implement FMRs. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-10-09mlx4_core: Reserve the correct number of MTT segmentsRoland Dreier
Taking ilog2(dev->caps.reserved_mtts) to find out the order to pass to the MTT buddy allocator will do the wrong thing if reserved_mtts is ever not a power of 2. Be safe and use fls(dev->caps.reserved_mtts - 1). Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-28mlx4_core: Remove kfree() in mlx4_mr_alloc() error flowJack Morgenstein
mlx4_mr_alloc() doesn't actually allocate mr (it just initializes the pointer that the caller passes in), so it shouldn't free it if an error occurs. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-06-07mlx4_core: Don't set MTT address in dMPT entries with PA setJack Morgenstein
If a dMPT entry has the PA flag (direct physical address) set, then the (unused) MTT base address field has to be set to 0. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-08IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adaptersRoland Dreier
Add an InfiniBand driver for Mellanox ConnectX adapters. Because these adapters can also be used as ethernet NICs and Fibre Channel HBAs, the driver is split into two modules: mlx4_core: Handles low-level things like device initialization and processing firmware commands. Also controls resource allocation so that the InfiniBand, ethernet and FC functions can share a device without stepping on each other. mlx4_ib: Handles InfiniBand-specific things; plugs into the InfiniBand midlayer. Signed-off-by: Roland Dreier <rolandd@cisco.com>