| Age | Commit message (Collapse) | Author |
|---|
|
This patch lets RBTX49XX boards use generic platform_driver interface
for the ne driver.
* Use platform_device to pass ioaddr and irq to the ne driver.
* Remove unnecessary ifdefs for RBTX49XX from the ne driver.
* Make the ne driver selectable on these boards regardless of CONFIG_ISA
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add NEEDS_PORTLIST cpp macro to control ISA auto-probe.
(I'm not sure M32R needs auto-probe but it is current behavior)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Miscellaneous fixes to make ne platform driver work properly.
* Make ioaddr 'unsigned long'.
* Move a printk down to show dev->name assigned in register_netdev.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add a platform_driver interface to ne driver.
(Existing legacy ports did not covered by this ne_driver for now)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
On Sat, 10 Jun 2006 14:11:42 +0200 (MEST) Mikael Pettersson wrote:
> While compiling 2.6.17-rc6 for a 486 with an NE2000 ISA ethernet card, I got:
>
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x158) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x176) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x183) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x1ea) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x251) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x266) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x29b) and 'ne_block_input'
>
> Not sure how serious this is; the driver seems to work fine later on.
Doesn't look serious. init_module() is not __init, but it calls
some __init functions and touches some __initdata.
BTW, I would be happy to see some consistent results from modpost
section checking. I don't see all of these warnings (I see only 1)
when using gcc 3.3.6. What gcc version are you using?
Does that matter? (not directed at anyone in particular)
Patch below fixes it for me. Please test/report.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Ensure that 8-bit mode is selected for the on-board Realtek RTL8019AS chip
on Toshiba RBHMA4x00, get rid of the duplicate #ifdef's when setting
ei_status.word16.
The chip's datasheet says that the PSTOP register shouldn't exceed 0x60 in
8-bit mode -- ensure this too.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
|
|
Correct the base address of the Realtek RTL8019AS chip on the Toshiba RBTX4938
board -- this should make the driver work at least when CONFIG_PCI is enabled.
Signed-off-by: Yuri Shpilevsky <yshpilevsky@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
They deal with wrapping correctly and are nicer to read. Also make
jiffies-holding variables unsigned long.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
These warnings are emitted if non-modular network drivers are built.
Fixes just move cleanup_card() definitions into #ifdef MODULE region.
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/wd.c:131: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/3c503.c:152: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/ne.c:216: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/hp.c:106: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/hp-plus.c:142: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/smc-ultra.c:172: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/e2100.c:144: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/es3210.c:159: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/lne390.c:149: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/lance.c:313: warning: 'cleanup_card' defined but not used
/.1/usr/srcdevel/kernel/linux-2.6.15-rc7.src/drivers/net/ac3200.c:127: warning: 'cleanup_card' defined but not used
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
Support for Toshiba's RBHMA4500 eval board for the TX4938.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/ne.c | 15 +++++++++++++++
1 files changed, 15 insertions(+)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
turn many #if $undefined_string into #ifdef $undefined_string to fix some
warnings after -Wno-def was added to global CFLAGS
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
