| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change driver version to 4.0.0. Netxen firmwares as old as
v3.4.216 are supported.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Enable tso6 and ipv6 checksum, interrupt coalescing for NX3031.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
NX3031 supports cut-through operation where ingress packets are
directly dma'ed into host buffers to reduce latency.
This requires larger dma buffers (2kb) and different alignemnt.
The buffer posting logic is changed a bit. The free rx buffers
are maintained in linked list, since the received reference
handles can be out of order. However rx descriptors are still
posted sequentially, indexed by producer.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
MAC addr, multicast filters, mtu are set through firmware commands
in firmware v4.0.0+ because of virtualization of physical ports.
Link status is also read from registers allocated by firmware for
each virtual port.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Contains rx and tx ring context management and certain
firmware commands for netxen firmware v4.0.0+.
This patch gathers all HW context management code into
netxen_nic_ctx.c.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
It had only couple of functions which are moved to main.c
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add initialization code in pci probe for new chip and retain
compatibility with old revisions.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
New revision of netxen chip has 2MB PCI memory. Older chips
had 128MB addressable PCI memory. To retain compatibility,
this patch adds function pointers based on pci bar0 size.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add macros for new chip revision and board configurations.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Enable multicast address filtering capabilities in the hardware.
Upto 16 multicast addresses can be programmed for each physical
port. Support "allmulti" mode, if enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
o Reduce access to global arrays in data path.
o Remove duplicate/unused variables, unecessary alignment constraints.
o Use correct pci_dev instead of fallback device for consistent
allocations.
o Disable ethtool set_eeprom functionality for now, it was only used
for flashing firmware.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
PCI_DEVICE_CLASS sets .device and .vendor to PCI_ANY_DEV,
which overrides the effect of preceding PCI_DEVICE() and makes
all elements of netxen_pci_tbl[] identical. Introduced in the
commit dcd56fdbaeae1008044687b973c4a3e852e8a726.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Downloading firmware in pci probe allows recovery in case of
firmware failure by reloading the driver.
Also reduced delays in firmware load.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
o Remove unnecessary debug prints and functions.
o Explicitly specify pci class (0x020000) to avoid enabling
management function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Store physical port number in netxen_adapter structure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This fixes a the issue where logical port number is set incorrectly
for HP blade mezz cards.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (48 commits)
net: Fix wrong interpretation of some copy_to_user() results.
xfrm: alg_key_len & alg_icv_len should be unsigned
[netdrvr] tehuti: move ioctl perm check closer to function start
ipv6: Fix typo in net/ipv6/Kconfig
via-velocity: fix vlan receipt
tg3: sparse cleanup
forcedeth: realtek phy crossover detection
ibm_newemac: Increase MDIO timeouts
gianfar: Fix skb allocation strategy
netxen: reduce stack usage of netxen_nic_flash_print
smc911x: test after postfix decrement fails in smc911x_{reset,drop_pkt}
net drivers: fix platform driver hotplug/coldplug
forcedeth: new backoff implementation
ehea: make things static
phylib: Add support for board-level PHY fixups
[netdrvr] atlx: code movement: move atl1 parameter parsing
atlx: remove flash vendor parameter
korina: misc cleanup
korina: fix misplaced return statement
WAN: Fix confusing insmod error code for C101 too.
...
|
|
Don't need to keep a struct netxen_new_user_info on the stack
when we only are interested in printing the serial_num. Change
to only reading the serial_num.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
This patch #if 0's the no longer used netxen_nic_link_ok().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
netxen_workq can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Don't count rx dropped packets based on return value of netif_receive_skb(),
which is misleading.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
o eliminate tx lock in netxen adapter struct, instead pound on netdev
tx lock appropriately.
o remove old "concurrent transmit" code that unnecessarily drops and
reacquires tx lock in hard_xmit_frame(), this is already serialized
the netdev xmit lock.
o reduce scope of tx lock in tx cleanup. tx cleanup operates on
different section of the ring than transmitting cpus and is
guarded by producer and consumer indices. This fixes a race
caused by rx softirq preemption on realtime kernels.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
o separate and simpler irq handler for msi interrupts, avoids few checks
than legacy mode.
o avoid redudant tx_has_work() and rx_has_work() checks in interrupt
and napi, which can uncork irq based on racy (lockless) access to tx
and rx ring indices. If we get interrupt, there's sufficient reason to
schedule napi.
o replenish rx ring more often, remove self-imposed threshold rcv_free
that prevents posting rx desc to card. This improves performance in
low memory.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Recent netxen firmware has new scheme of generating MSI interrupts, it
raises interrupt and blocks itself, waiting for driver to unmask. This
reduces chance of spurious interrupts.
The driver will be able to deal with older firmware as well.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch contains the following cleanups:
- static functions in .c files shouldn't be marked inline
- make needlessly global code static
- #if 0 unused code
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Using ARRAY_SIZE() on arrays of the form array[][K] makes it unnecessary
to know the value of K when checking its size.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Here's the reworked patch.
This cleans up some unnecessary byte-swapping while setting up tx and
interpreting rx desc. The 64 bit rx status data should be converted
to host endian format only once and the macros just need to extract
bitfields.
This saves a spate of interrupts on pseries blades caused by buggy
(non) processing rx status ring.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
netxen driver allows limited number of threads simultaneously posting
skb's in tx ring. If transmit slot is unavailable, driver calls
schedule() or loops in xmit_frame().
This patch returns TX_BUSY and lets the stack reschedule the packet if
transmit slot is unavailable. Also removes unnecessary check for tx
timeout in the driver itself, the network stack does that anyway.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch fixes bug that doesn't quiesce second port when interface is
brought down, which could lead to unwarranted interrupt during rmmod /
ifdown.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Bumping up driver version to 3.4.18, several fixes have gone in since
version 3.4.2.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
If work_done >= budget we should always elide the NAPI
completion.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove always-false tests in irq handler.
Also a few other minor cleanups.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Remove redundant DMA_..BIT_MASK definitions across two drivers. The
computation of the majority of the bitmasks is done by the compiler. The
initial split of the patch touching each a different file got removed due
to possible git bisect breakage.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Reviewed-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Resubmitting the patch.
This patch improves ethtool support for printing correct ring statistics,
segmentation offload status, etc.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is nicer than the MAC_FMT stuff.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch covers something like this:
dev = alloc_*dev(...
...
priv = netdev_priv(dev);
memset(priv, 0, sizeof(*priv));
The memset() here is superfluous. alloc_netdev() uses kzalloc()
to allocate needed memory so there is no need to zero the priv region
twice.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch cleans up duplicate includes in
drivers/net/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes two problems during driver unload. The pci_disable_device()
call is before firmware reload, causing reads and writes across PCI bus after
disabling device. Second problem is the register window was wrong during
firmware reload
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
