summaryrefslogtreecommitdiffstats
path: root/drivers/net/phy/Makefile
AgeCommit message (Collapse)Author
2012-10-18phy: add AT803x driverMatus Ujhelyi
This driver add support for wake over lan on AT803x phys. Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-30netdev/phy: add MDIO bus multiplexer driven by a memory-mapped deviceTimur Tabi
Add support for an MDIO bus multiplexer controlled by a simple memory-mapped device, like an FPGA. The device must be memory-mapped and contain only 8-bit registers (which keeps things simple). Tested on a Freescale P5020DS board which uses the "PIXIS" FPGA attached to the localbus. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-27netdev/phy: Add driver for Broadcom BCM87XX 10G Ethernet PHYsDavid Daney
Add a driver for BCM8706 and BCM8727 devices. These are a 10Gig PHYs which use MII_ADDR_C45 addressing. They are always 10G full duplex, so there is no autonegotiation. All we do is report link state and send interrupts when it changes. If the PHY has a device tree of_node associated with it, the "broadcom,c45-reg-init" property is used to supply register initialization values when config_init() is called. Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-07netdev/of/phy: Add MDIO bus multiplexer driven by GPIO lines.David Daney
The GPIO pins select which sub bus is connected to the master. Initially tested with an sn74cbtlv3253 switch device wired into the MDIO bus. Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-07netdev/of/phy: Add MDIO bus multiplexer support.David Daney
This patch adds a somewhat generic framework for MDIO bus multiplexers. It is modeled on the I2C multiplexer. The multiplexer is needed if there are multiple PHYs with the same address connected to the same MDIO bus adepter, or if there is insufficient electrical drive capability for all the connected PHY devices. Conceptually it could look something like this: ------------------ | Control Signal | --------+--------- | --------------- --------+------ | MDIO MASTER |---| Multiplexer | --------------- --+-------+---- | | C C h h i i l l d d | | --------- A B --------- | | | | | | | PHY@1 +-------+ +---+ PHY@1 | | | | | | | --------- | | --------- --------- | | --------- | | | | | | | PHY@2 +-------+ +---+ PHY@2 | | | | | --------- --------- This framework configures the bus topology from device tree data. The mechanics of switching the multiplexer is left to device specific drivers. The follow-on patch contains a multiplexer driven by GPIO lines. Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-19phy: add am79c874 PHY supportHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-19phy: Micrel KS8995MA 5-ports 10/100 managed Ethernet switch support addedFrederic LAMBERT
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Frederic Lambert <frdrc66@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-23ptp: Added a clock driver for the National Semiconductor PHYTER.Richard Cochran
This patch adds support for the PTP clock found on the DP83640. The basic clock operations and one external time stamp have been implemented. Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: John Stultz <john.stultz@linaro.org>
2010-05-03drivers/net/phy: micrel phy driverDavid J. Choi
This is the first version of phy driver from Micrel Inc. Signed-off-by: David J. Choi <david.choi@micrel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-17NET: Add driver for Octeon MDIO buses.David Daney
The Octeon SOC has two types of Ethernet ports, each type with its own driver. However, the PHYs for all the ports are controlled by a common MDIO bus. Because the mdio driver is not associated with a particular driver, but is instead a system level resource, we create s stand-alone driver for it. As for the driver, we put the register definitions in arch/mips/include/asm/octeon where most of the other Octeon register definitions live. This is a platform driver with the platform device for "mdio-octeon" being registered in the platform startup code. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-07-07MIPS: BCM63XX: Add integrated ethernet PHY support for phylib.Maxime Bizon
Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> drivers/net/phy/Kconfig | 6 ++ drivers/net/phy/Makefile | 1 drivers/net/phy/bcm63xx.c | 132 ++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 139 insertions(+) create mode 100644 drivers/net/phy/bcm63xx.c Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09phy: Add LSI ET1011C PHY driverChaithrika U S
Adds LSI ET1011C PHY driver. This driver is used by TI DM646x EVM. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-28phy: add the ST ste10Xp PHYsGiuseppe Cavallaro
This patch adds the STMicroelectronics ste10xp PHY device driver. It supports both the ste100p and the ste101p devices. Suspend/resume alredy added. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-28phy: add natsemi PHY driverGiuseppe Cavallaro
This patch adds the PHY device driver for the National Semiconductor DP83865 Gig PHYTER. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-16phylib: rename mdio-ofgpio to mdio-gpioPaulius Zaleckas
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-05-30net: OpenFirmware GPIO based MDIO bitbang driverLaurent Pinchart
This patch adds an MDIO bitbang driver that uses the GPIO library and its OF bindings to access the bus I/Os. Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-02-03phylib: Add Realtek 821x eth PHY supportJohnson Leung
this PHY present on the MPC8315E and MPC837xE RDB boards. Signed-off-by: Johnson Leung <r58129@freescale.com> Signed-off-by: Kevin Lam <r43770@freescale.com> Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10Generic bitbanged MDIO libraryScott Wood
Previously, bitbanged MDIO was only supported in individual hardware-specific drivers. This code factors out the higher level protocol implementation, reducing the hardware-specific portion to functions setting direction, data, and clock. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-08phylib: add the ICPlus IP175C PHY driverMichael Barkowski
The ICPlus IP175C sports a 100Mbit/s 4-port switch in addition to a dedicated 100Mbit/s WAN port. Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-02[PATCH] 2.6.18: sb1250-mac: Broadcom PHY supportMaciej W. Rozycki
This patch adds support for interrupt-driven operation of the Broadcom Gigabit Ethernet PHYs. I have included device IDs for the parts used on Broadcom SiByte evaluation boards; more can be added as a need arises. They are apparently generally software-compatible with one another. Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> patch-mips-2.6.18-20060920-broadcom-phy-15 Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-19[PATCH] PAL: Support of the fixed PHYVitaly Bordug
This makes it possible for HW PHY-less boards to utilize PAL goodies. Generic routines to connect to fixed PHY are provided, as well as ability to specify software callback that fills up link, speed, etc. information into PHY descriptor (the latter feature not tested so far). Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpcLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (139 commits) [POWERPC] re-enable OProfile for iSeries, using timer interrupt [POWERPC] support ibm,extended-*-frequency properties [POWERPC] Extra sanity check in EEH code [POWERPC] Dont look for class-code in pci children [POWERPC] Fix mdelay badness on shared processor partitions [POWERPC] disable floating point exceptions for init [POWERPC] Unify ppc syscall tables [POWERPC] mpic: add support for serial mode interrupts [POWERPC] pseries: Print PCI slot location code on failure [POWERPC] spufs: one more fix for 64k pages [POWERPC] spufs: fail spu_create with invalid flags [POWERPC] spufs: clear class2 interrupt status before wakeup [POWERPC] spufs: fix Makefile for "make clean" [POWERPC] spufs: remove stop_code from struct spu [POWERPC] spufs: fix spu irq affinity setting [POWERPC] spufs: further abstract priv1 register access [POWERPC] spufs: split the Cell BE support into generic and platform dependant parts [POWERPC] spufs: dont try to access SPE channel 1 count [POWERPC] spufs: use kzalloc in create_spu [POWERPC] spufs: fix initial state of wbox file ... Manually resolved conflicts in: drivers/net/phy/Makefile include/asm-powerpc/spu.h
2006-06-21[POWERPC] Add Vitesse 8244 PHY for MPC8641 HPCN platform.Jon Loeliger
Signed-off-by: Kriston Carson <KristonCarson@freescale.com> Signed-off-by: Xianghua Xiao <x.xiao@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-05-24[PATCH] phy: new SMSC LAN83C185 PHY driverHerbert Valerio Riedel
new SMSC LAN83C185 10BaseT/100BaseTX PHY driver for the PHY subsystem Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2005-08-28[PATCH] PHY Layer fixupAndy Fleming
This patch adds back the code that was taken out, thus re-enabling: * The PHY Layer to initialize without crashing * Drivers to actually connect to PHYs * The entire PHY Control Layer This patch is used by the gianfar driver, and other drivers which are in development. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-08-11Fix numerous minor problems with new phy subsystem.Jeff Garzik
Includes fixes for problems noted by Adrian Bunk, Andrew Morton, and one other person lost in the annals of history (and email folders).
2005-07-30This patch adds a PHY Abstraction Layer to the Linux Kernel, enablingAndy Fleming
ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>