| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds code to disable the TXC and RXC reference clocks if link
is not available.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds an RXC auto power-down feature to the code that supports
the gphys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 5785 does not use the RXC reference clock. Turning it off is
desirable as it saves power.
By default, the 50610 enables the RXC reference clock and the 50610M
disables it. Presumably this is one of the reasons why the hardware
architect chose one over the other.
Adding a "rx reference clock disable" flag is not the ideal way to
describe the option, as it would force the MAC using a 50610M to set
the flag. Ideally we want the flags to represent opt-in behavior that
deviates from hardware defaults. Furthermore, the lack of a
"disable" flag implies that the requester wants the rx reference clock
enabled, which doesn't necessarily follow.
By presenting the option as a passive statement (rx reference clock
unused) rather than a command, I hope to convey an opt-in option to
disable the rx reference clock that falls back to hardware defaults if
not set. A secondary benefit of this is that it keeps the
intelligence about phy defaults in the broadcom module where it belongs
and allows the broadcom module more latitude should a bug arise.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Auto power-down (APD) support is a power-saving feature. It should be
selectively enabled since it might expose MAC bugs. This patch changes
the code to enable APD only if the PHY_BRCM_AUTO_PWRDWN_ENABLE flag is
set. The tg3 driver was changed to set this bit.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Broadcom 50610M parts changed the default definitions of the RGMII mode
shadow register. The 5785 needs the RGMII mode selection bits [4:3]
cleared.
The default value of the remaining bits in this register are zero.
Rather than unnecessarily burn an extra bit in the dev_flags member in
an attempt to enumerate all possible combinations, this patch take a
more course grained approach and labels the option as "clear all bits".
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves all the dev_flags enumerations outside the broadcom.c
file to include/linux/brcmphy.h. The existing flags were not used yet
and have been re-enumerated to avoid conflicts.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a 50610 or 50610M is paired against particular remote partners,
link is slow to come up. This patch works around the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch consolidates the code that requires the SMDSP clock to be
enabled into a single function that (hopefully) makes the dependency
obvious.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some OF platform drivers are missing module device tables, so they won't
load automatically on boot. This patch fixes the issue by adding proper
MODULE_DEVICE_TABLE() macros to the drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to specs, when auto-negotiation is disabled, Marvell PHYs need
a software reset after changing speed/duplex forcing bits. Otherwise,
the modified bits have no effect.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This brings the 57780's phy into IEEE compliance by suppressing the
common mode oscillation.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the AC131 fast ethernet transceiver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the BCM50610M phy ID.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/iwmc3200wifi/netdev.c
net/wireless/scan.c
|
|
Changes to the fs_enet driver aa73832c5a80d6c52c69b18af858d88fa595dd3c
("net: Rework fs_enet driver to use of_mdio infrastructure")
cause kernel crashes when using the mdio-ofgpio driver.
This patch replicates similar changes made to the fs_enet mii-bitbang
drivers. It has been tested on a custom mpc8280 based board using an
NFS mounted root.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/orinoco/main.c
|
|
Don't forget to unlock a mutex in phy_scan_fixups on a fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/phy/Kconfig | 6 ++
drivers/net/phy/Makefile | 1
drivers/net/phy/bcm63xx.c | 132 ++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 139 insertions(+)
create mode 100644 drivers/net/phy/bcm63xx.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY_HALTED state disables phydev->link, but the link will not be
updated upon entering PHY_RESUMING. Add a call to phy_read_status() to
update the link before entering PHY_RUNNING. If the link is not up at
this point, enter the PHY_NOLINK state instead.
Also, when transitioning from PHY_RESUMING to PHY_RUNNING, calls to
netif_carrier_on() and phydev->adjust_link() are missing. Add the calls
similar to the other transitions to PHY_RUNNING.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix kernel-doc parameter name in phy_device.c.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disable fiber/copper auto selection for Marvell m88e1111 SGMII support.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add phy_connect_direct() and phy_attach_direct() functions so that
drivers can use a pointer to the phy_device instead of trying to determine
the phy's bus_id string.
This patch is useful for OF device tree descriptions of phy devices where
the driver doesn't need or know what the bus_id value in order to get a
phy_device pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes changes in preparation for supporting open firmware
device tree descriptions of MDIO busses. Changes include:
- Cleanup handling of phy_map[] entries; they are already NULLed when
registering and so don't need to be re-cleared, and it is good practice
to clear them out when unregistering.
- Split phy_device registration out into a new function so that the
OF helpers can do two stage registration (separate allocation and
registration steps).
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit a390d1f3 ("phylib: convert state_queue work to
delayed_work") missed converting 'expires' value to 'delay' value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add did_interrupt() function to check if a PHY port
really caused an interrupt. This is needed in the case
of shared PHY interrupt pin configuration to stop
interrupt event processing for PHY ports which didn't
cause an interrupt.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell 88E1121R Dual PHY device can be hardware-configured
to use shared interrupt pin for both PHY ports. For such
PHY configurations using shared PHY interrupt phy_interrupt()
handler will also schedule a work for PHY port which didn't
cause an interrupt.
This patch adds a possibility for PHY drivers to provide
did_interrupt() function which reports if the PHY (or a PHY
port in a multi-PHY device) generated an interrupt. This
function is called in phy_change() as phy_change() shouldn't
proceed if it is invoked for a PHY which didn't cause an
interrupt. So check for interrupt originator in phy_change()
to allow early-out.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Marvell M88E1121R Dual GigE PHY
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
platform_device_register_simple() returns ERR_PTR() and not NULL.
Found by smatch (http://repo.or.cz/w/smatch.git). Compile tested.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is a fairly common operation to have a pointer to a work and to need a
pointer to the delayed work it is contained in. In particular, all
delayed works which want to rearm themselves will have to do that. So it
would seem fair to offer a helper function for this operation.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
LAN8710 and LAN8720 are two new 10/100 ethernet PHY models. The two
share the same phy id, this patch adds it to the smsc phy driver.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It closes a race in phy_stop_machine when reprogramming of phy_timer
(from phy_state_machine) happens between del_timer_sync and cancel_work_sync.
Without this change it could lead to crash if phy_device would be freed after
phy_stop_machine (timer would fire and schedule freed work).
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
|
|
mdc pin should always be output. Initialize it as output,
so each board code does not need to do this.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In most cases (e.g. PCI drivers) MDIO and MAC controllers are
represented by the same device. But for SOC ethernets we have
separate devices. So, in SOC case, checking whether MDIO
controller may wakeup is not only makes little sense, but also
prevents us from doing per-netdevice wakeup management.
This patch reworks suspend/resume code so that now it checks
for net device's wakeup flags, not MDIO controller's ones.
Each netdevice should manage its wakeup flags, and phylib will
decide whether suspend an attached PHY or not.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
All supported SMSC PHYs implement the standard "power down" bit 11 of
BMCR, so this patch adds support using the generic genphy_{suspend,resume}
functions.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suspend/resume routines check for phydrv != NULL, but that is
wrong because "phydrv" comes from container_of(drv). If drv is NULL,
then container_of(drv) will return non-NULL result, and the checks
won't work.
The Freescale TBI PHYs are driver-less, so "drv" is NULL, and that
leads to the following oops:
Unable to handle kernel paging request for data at address 0xffffffe4
Faulting instruction address: 0xc0215554
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c0215554] mdio_bus_suspend+0x34/0x70
LR [c01cc508] suspend_device+0x258/0x2bc
Call Trace:
[cfad3da0] [cfad3db8] 0xcfad3db8 (unreliable)
[cfad3db0] [c01cc508] suspend_device+0x258/0x2bc
[cfad3dd0] [c01cc62c] dpm_suspend+0xc0/0x140
[cfad3e20] [c01cc6f4] device_suspend+0x48/0x5c
[cfad3e40] [c0068dd8] suspend_devices_and_enter+0x8c/0x148
[cfad3e60] [c00690f8] enter_state+0x100/0x118
[cfad3e80] [c00691c0] state_store+0xb0/0xe4
[cfad3ea0] [c018c938] kobj_attr_store+0x24/0x3c
[cfad3eb0] [c00ea9a8] flush_write_buffer+0x58/0x7c
[cfad3ed0] [c00eadf0] sysfs_write_file+0x58/0xa0
[cfad3ef0] [c009e810] vfs_write+0xb4/0x16c
[cfad3f10] [c009ed40] sys_write+0x4c/0x90
[cfad3f40] [c0014954] ret_from_syscall+0x0/0x38
[...]
This patch fixes the issue, plus removes unneeded parentheses
and fixes indentation level in mdio_bus_suspend().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
both pdata->mdc and pdata->mdio are unsigned. Notice a negative
return value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Freescale on-chip TBI PHYs reports PHY ID as 0x0, but as of
commit 3ee82383f0098a2e13acc8cf1be8e47512f41e5a
Author: Giulio Benetti <giulio.benetti@micronovasrl.com>
Date: Thu Nov 13 21:53:13 2008 +0000
phy: fix phy address bug
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
phy_device.c treats PHY ID == 0x0 as bogus IDs, and that results in
gianfar driver failure to see the TBI PHYs. This code snippet triggers:
if (!priv->tbiphy) {
printk(KERN_WARNING "SGMII mode requires that the device "
"tree specify a tbi-handle\n");
return;
}
Although tbi-handle is specified in the device tree.
Btw, technically PHY ID == 0x0 is a valid ID (if we ever see a PHY
manufactured by Xerox :-).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHYLIB mdio code has more problems in error paths:
- mdiobus_release can be called before bus->state is set to
MDIOBUS_REGISTERED
- mdiobus_scan allocates resources which need to be freed
- the comment is wrong, the resistors used are actually pull-ups.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/ppp_generic.c
|
|
kernel BUG at drivers/net/phy/mdio_bus.c:165!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
How?
mdiobus_alloc() sets bus->state = MDIOBUS_ALLOCATED.
mdiobus_register() sets bus->state = MDIOBUS_REGISTERED but then can
fail (mdiobus_scan()) returning an error to the caller.
The caller aborts correctly with mdiobus_free() which does:
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
genphy_setup_forced hasn't actually reset the PHY for a long time,
but a comment to that effect remained in the code, so code continued
to act as if it *had* reset the PHY, and called the necessary fixup
functions to respond to a PHY reset. With no reset, those functions
are no longer needed, so we remove them.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds LSI ET1011C PHY driver.
This driver is used by TI DM646x EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the STMicroelectronics ste10xp PHY device driver.
It supports both the ste100p and the ste101p devices.
Suspend/resume alredy added.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
