| Age | Commit message (Collapse) | Author |
|---|
|
Correct a mistake made in the previous commit due to reckless
copy-and-pasting.
Signed-off-by: Patrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A SMSC PHY in power down mode can't be used.
If a SMSC PHY is in this mode in the config_init
stage, the mode "all capable" is set. So the PHY
could then be used.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added functions for ack_interrupt and config_intr. Tested on an mpc5200b
powerpc board.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
this will allow to detect the link between the switch and the soc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor line offset auto-merges.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch re-enables Energy Detect Power Down (EDPD) mode for the
LAN8710/LAN8720. EDPD mode was disabled in a previous commit,
(b629820d18fa65cc598390e4b9712fd5f83ee693), because it was causing the
PHY to not be able to detect a link when cold started without a cable
connected.
The LAN8710/LAN8720 requires a minimum of 2 link pulses within 64ms of
each other in order to set the ENERGYON bit and exit EDPD mode. If a
link partner does send the pulses within this interval, the PHY will
remained powered down.
This workaround will manually toggle the PHY on/off upon calls to
read_status in order to generate link test pulses if the link is down.
If a link partner is present, it will respond to the pulses, which will
cause the ENERGYON bit to be set and will cause the EDPD mode to be
exited.
Signed-off-by: Patrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mdiobus_free"
This reverts commit aa731872f7d33dcb8b54dad0cfb82d4e4d195d7e.
As pointed out by Ben Hutchings, this change is not correct.
mdiobus_unregister() can't be called if the bus isn't registered yet,
however this change can result in situations which cause that to
happen.
Part of the confusion here revolves around the fact that the
callers of this module control registration/unregistration,
rather than the module itself.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both these PHYs support interrupt generation on IC pin 32.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a phy_id sysfs attribute to MDIO devices, containing the
32-bit PHY identifier reported by the device. This attribute can
be useful when debugging problems related to phy drivers. Other
enumerable buses already have similar attributes.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on commit b27393aecf66199f5ddad37c302d3e0cfadbe6c0
Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.
The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
... when != mdiobus_unregister(E);
+ mdiobus_unregister(E);
mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver add support for wake over lan on AT803x phys.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that of_mdio_find_bus() matches the prototype in the header (and
stop sparse complaining) by including the header with the prototype.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LAN8710/LAN8720 chips do have broken the "FlexPWR" smart power-saving
capability. Enabling it leads to the PHY not being able to detect Link when
cold-started without cable connected. Thus, make sure this is disabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christian Hohnstaedt <chohnstaedt@innominate.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds proper handling of the buggy revision A2 of LXT973 phy, adding
precautions linked to ERRATA Item 4:
Revision A2 of LXT973 chip randomly returns the contents of the previous even
register when you read a odd register regularly
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no such part as KS8001, KS8041 or KS8051. There are only
KSZ8001, KSZ8041 and KSZ8051. Rename these parts as such to match
the Micrel naming.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ8021 PHY was previously caught by KS8051, which is not correct.
This PHY needs additional setup if it is strapped for address 0. In such
case an reserved bit must be written in the 0x16, "Operation Mode Strap
Override" register. According to the KS8051 datasheet, that bit means
"PHY Address 0 in non-broadcast" and it indeed behaves as such on KSZ8021.
The issue where the ethernet controller (Freescale FEC) did not communicate
with network is fixed by writing this bit as 1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PTP Hardware Clock devices appear as class devices in sysfs. This patch
changes the registration API to use the parent device, clarifying the
clock's relationship to the underlying device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the driver has no MODULE_LICENSE attribute in its source which
results in a kernel taint if I load this:
root@(none):~# modprobe bcm87xx
bcm87xx: module license 'unspecified' taints kernel.
Since the first lines of the source code clearly state:
* This file is subject to the terms and conditions of the GNU General
* Public License. See the file "COPYING" in the main directory of this
* archive for more details.
I think it's safe to add the MODULE_LICENSE("GPL") macro and thus remove
the kernel taint.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mdio-mux-mmioreg.c uses function of_address_to_resource(), which is defined
in linux/of_address.h. This fixes a compilation error:
drivers/net/phy/mdio-mux-mmioreg.c: In function 'mdio_mux_mmioreg_probe':
drivers/net/phy/mdio-mux-mmioreg.c:83:2: error: implicit declaration of
function 'of_address_to_resource'
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for an MDIO bus multiplexer controlled by a simple memory-mapped
device, like an FPGA. The device must be memory-mapped and contain only
8-bit registers (which keeps things simple).
Tested on a Freescale P5020DS board which uses the "PIXIS" FPGA attached
to the localbus.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch cleans up the way device tree support is added in mdio-gpio
driver. I found lot of code duplication which is not necessary.
Also strangely a new platform driver was also introduced for device tree
support. All this forced me to do this cleanup patch.
After this patch, the driver probe checks the of_node pointer to get the
data from device tree.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The helper functions which translate IEEE MDIO Manageable Device (MMD)
Energy-Efficient Ethernet (EEE) registers 3.20, 7.60 and 7.61 to and from
the comparable ethtool supported/advertised settings will be needed by
drivers other than those in PHYLIB (e.g. e1000e in a follow-on patch).
In the same fashion as similar translation functions in linux/mii.h, move
these functions from the PHYLIB core to the linux/mdio.h header file so the
code will not have to be duplicated in each driver needing MMD-to-ethtool
(and vice-versa) translations. The function and some variable names have
been renamed to be more descriptive.
Not tested on the only hardware that currently calls the related functions,
stmmac, because I don't have access to any. Has been compile tested and
the translations have been tested on a locally modified version of e1000e.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mdio-mux driver scans all child mdio nodes, without regard to whether
the node is actually used. Some device trees include all possible
mdio-mux nodes and rely on the boot loader to disable those that are not
present, based on some run-time configuration. Those nodes need to be
skipped.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
devm_kfree should not have to be explicitly used.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,d;
@@
x = devm_kzalloc(...)
...
?-devm_kfree(d,x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull MIPS updates from Ralf Baechle:
"More hardware support across the field including a bunch of device
drivers. The highlight however really are further steps towards
device tree.
This has been sitting in -next for ages. All MIPS _defconfigs have
been tested to boot or where I don't have hardware available, to at
least build fine."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (77 commits)
MIPS: Loongson 1B: Add defconfig
MIPS: Loongson 1B: Add board support
MIPS: Netlogic: early console fix
MIPS: Netlogic: Fix indentation of smpboot.S
MIPS: Netlogic: remove cpu_has_dc_aliases define for XLP
MIPS: Netlogic: Remove unused pcibios_fixups
MIPS: Netlogic: Add XLP SoC devices in FDT
MIPS: Netlogic: Add IRQ mappings for more devices
MIPS: Netlogic: USB support for XLP
MIPS: Netlogic: XLP PCIe controller support.
MIPS: Netlogic: Platform changes for XLR/XLS I2C
MIPS: Netlogic: Platform NAND/NOR flash support
MIPS: Netlogic: Platform changes for XLS USB
MIPS: Netlogic: Remove NETLOGIC_ prefix
MIPS: Netlogic: SMP wakeup code update
MIPS: Netlogic: Update comments in smpboot.S
MIPS: BCM63XX: Add 96328avng reference board
MIPS: Expose PCIe drivers for MIPS
MIPS: BCM63XX: Add PCIe Support for BCM6328
MIPS: BCM63XX: Move the PCI initialization into its own function
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
|
|
Get the MDIO bus controller addresses from the device tree, small
clean up in use of devm_*
Remove, now unused, platform device setup code.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3938/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
I no longer have a mailbox at smsc.com, and I've had two reports
that that email address now bounces from people trying to
contact me. This patch updates all references to that invalid
address to one that I can be contacted on more permanently.
This patch also updates the maintainer status to reflect
the fact I'm no longer directly paid to maintain these drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With lockdep enabled we get:
=============================================
[ INFO: possible recursive locking detected ]
3.4.4-Cavium-Octeon+ #313 Not tainted
---------------------------------------------
kworker/u:1/36 is trying to acquire lock:
(&bus->mdio_lock){+.+...}, at: [<ffffffff813da7e8>] mdio_mux_read+0x38/0xa0
but task is already holding lock:
(&bus->mdio_lock){+.+...}, at: [<ffffffff813d79e4>] mdiobus_read+0x44/0x88
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&bus->mdio_lock);
lock(&bus->mdio_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
.
.
.
This is a false positive, since we are indeed using 'nested' locking,
we need to use mutex_lock_nested().
Now in theory we can stack multiple MDIO multiplexers, but that would
require passing the nesting level (which is difficult to know) to
mutex_lock_nested(). Instead we assume the simple case of a single
level of nesting. Since these are only warning messages, it isn't so
important to solve the general case.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
broadcom, not marvell.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If registering of one of them fails, all already registered drivers
of this module will be unregistered.
Use the new register/unregister functions in all drivers
registering more than one driver.
amd.c, realtek.c: Simplify: directly return registration result.
Tested with broadcom.c
All others compile-tested.
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bcm87xx phys don't support autonegotiation, so don't use it by
default, as otherwise phy_state_machine() will try to enable it (using
c22 requests, which also don't make any sense for the bcm78xx).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).
An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.
In the end, this patch also adds the EEE ethtool support implementing:
o phy_ethtool_set_eee
o phy_ethtool_get_eee
v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
values according to ethtool API (thanks to Ben's feedback).
Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
Fixed the phy_init_eee function: we need to check which link mode
was autonegotiated and then the corresponding bits in 7.60 and 7.61
registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/phy/phy_device.c: In function ‘get_phy_device’:
drivers/net/phy/phy_device.c:340:14: warning: ‘phy_id’ may be used uninitialized in this function [-Wmaybe-uninitialized]
GCC can't see that when we return zero we always initialize
phy_id and that's the only path where we use it.
Initialize phy_id to zero to shut it up.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a driver for BCM8706 and BCM8727 devices. These are a 10Gig PHYs
which use MII_ADDR_C45 addressing. They are always 10G full duplex, so
there is no autonegotiation. All we do is report link state and send
interrupts when it changes.
If the PHY has a device tree of_node associated with it, the
"broadcom,c45-reg-init" property is used to supply register
initialization values when config_init() is called.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow PHY drivers to supply their own device matching function
(match_phy_device()), or to be matched OF compatible properties.
PHYs following IEEE802.3 clause 45 have more than one device
identifier constants, which breaks the default device matching code.
Other 10G PHYs don't follow the standard manufacturer/device
identifier register layout standards, but they do use the standard
MDIO bus protocols for register access. Both of these require
adjustments to the PHY driver to device matching code.
If the there is an of_node associated with such a PHY, we can match it
to its driver using the "compatible" properties, just as we do with
certain platform devices. If the "compatible" property match fails,
first check if there is a driver supplied matching function, and if
not fall back to the existing identifier matching rules.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IEEE802.3 clause 45 MDIO bus protocol allows for directly
addressing PHY registers using a 21 bit address, and is used by many
10G Ethernet PHYS. Already existing is the ability of MDIO bus
drivers to use clause 45, with the MII_ADDR_C45 flag. Here we add
struct phy_c45_device_ids to hold the device identifier registers
present in clause 45. struct phy_device gets a couple of new fields:
c45_ids to hold the identifiers and is_c45 to signal that it is clause
45.
get_phy_device() gets a new parameter is_c45 to indicate that the PHY
device should use the clause 45 protocol, and its callers are adjusted
to pass false. The follow-on patch to of_mdio.c will pass true where
appropriate.
EXPORT phy_device_create() so that the follow-on patch to of_mdio.c
can use it to create phy devices for PHYs, that have non-standard
device identifier registers, based on the device tree bindings.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On a freescale imx6q platform, a hardware phy chip KSZ9021 is
recognized as a KS8001 chip by the current driver like this:
eth0: Freescale FEC PHY driver [Micrel KS8001 or KS8721]
KSZ9021 has phy_id 0x00221610, while KSZ8001 has phy_id
0x0022161a, the current phy_id_mask (0x00fffff0/0x00ffff10) can't
distinguish them. So change phy_id_mask to resolve this problem.
Although the micrel datasheet says that the 4 LSB of phyid2 register
contains the chip revision number and the current driver is designed
to follow this rule, in reality the chip implementation doesn't follow
it.
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a more current logging style.
Add pr_fmt and missing newlines.
Remove embedded prefixes.
Neaten phy_print_status to avoid using KERN_CONT.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix kernel-doc warnings in drivers/net/phy:
Warning(drivers/net/phy/mdio_bus.c:109): No description found for parameter 'mdio_bus_np'
Warning(drivers/net/phy/mdio_bus.c:109): Excess function parameter 'mdio_np' description in 'of_mdio_find_bus'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the interrupt mask for IC101 A/G devices
and now enables the link/speed/duplex interrupts.
This is done by setting the "INTR pin used" bit and cleaning
all the other bits in the Register 17.
Reported-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
