summaryrefslogtreecommitdiffstats
path: root/drivers/net/qlcnic
AgeCommit message (Collapse)Author
2010-09-21qlcnic: dont set skb->truesizeEric Dumazet
skb->truesize is set in core network. Dont change it unless dealing with fragments. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-17qlcnic: dont assume NET_IP_ALIGN is 2Eric Dumazet
qlcnic driver allocates rx skbs and gives to hardware too bytes of extra storage, allowing for corruption of kernel data. NET_IP_ALIGN being 0 on some platforms (including x86), drivers should not assume it's 2. rds_ring->skb_size = rds_ring->dma_size + NET_IP_ALIGN; ... skb = dev_alloc_skb(rds_ring->skb_size); skb_reserve(skb, 2); pci_map_single(pdev, skb->data, rds_ring->dma_size, PCI_DMA_FROMDEVICE); (and rds_ring->skb_size == rds_ring->dma_size) -> bug Because of extra alignment (1500 + 32) -> four extra bytes are available before the struct skb_shared_info, so corruption is not noticed. Note: this driver could use netdev_alloc_skb_ip_align() Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-23qlcnic: fix poll implementationYinglin Luan
Function qlcnic_intr has pointer to qlcnic_host_sds_ring as second parameter not pointer to qlcnic_adapter. Signed-off-by: Yinglin Luan <synmyth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-19qlnic: fix a race in qlcnic_get_stats()Eric Dumazet
Dont clear netdev->stats, it might give transient wrong values to concurrent stat readers. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-10qlcnic: using too much stackDan Carpenter
qlcnic_pci_info structs are 128 bytes so an array of 8 uses 1024 bytes. That's a lot if you run with 4K stacks. I allocated them with kcalloc() instead. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-10qlcnic: clean up qlcnic_init_pci_info()Dan Carpenter
In the original code we allocated memory conditionally and freed it in the error handling unconditionally. It turns out that this function is only called during initialization and "adapter->npars" and "adapter->eswitch" are always NULL at the start of the function. I removed those checks. Also since I was cleaning things, I changed the error handling for qlcnic_get_pci_info() and pulled everything in an indent level. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-25qlcnic: fix diag resource allocationSony Chacko
netif_device_attach missing from error path in qlcnic_diag_alloc_res Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-25qlcnic: fix loopback testAmit Kumar Salecha
o Loopback not supported for virtual function. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-24qlcnic: fix bandwidth checkRajesh Borundia
Fix maximum and minmum bandwith value. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-18qlcnic: fix pci resource leakAmit Kumar Salecha
pci_get_domain_bus_and_slot: caller must decrement the reference count by calling pci_dev_put(). Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-14qlcnic: restore NPAR config data after recoveryAnirban Chakraborty
o NPAR configuration which is programmed in fw, need to restore after fw recovery. o Update version to 5.0.7 Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-14qlcnic: aer supportSucheta Chakraborty
Pci error recovery support added. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-14qlcnic: fix netdev notifier in error pathAmit Kumar Salecha
netdev notifier are not unregistered if pci_register_driver fails. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-14qlcnic: disable tx timeout recoveryAmit Kumar Salecha
Disable tx timeout recovery, if auto_fw_reset is disable Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-14qlcnic: fix pause params settingRajesh Borundia
Turning off rx pause param and autoneg param is not supported so return error in that case. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-09qlcnic: Disable admin tools interface for VF driver modeAnirban Chakraborty
Non privileged (VF) driver will not be able to carry out any of the FW update, etc. operations. Disable the tools interface by not creating the sysfs nodes. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-09qlcnic: Check FW capability for TSOAnirban Chakraborty
Driver checks TSO capability from FW before enabling it. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-30netdev: Make ethtool_ops::set_flags() return -EINVAL for unsupported flagsBen Hutchings
The documented error code for attempts to set unsupported flags (or to clear flags that cannot be disabled) is EINVAL, not EOPNOTSUPP. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29qlcnic: Add support for configuring eswitch and nparsRajesh K Borundia
Following changes are made: 1.Obtain capabilities of Nic partition. 2.Configure tx bandwidth of particular Nic partition. 3.Configure the eswitch for setting port mirroring, enable mac learning, promiscous mode. Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29qlcnic: Remove obsolete codeAnirban Chakraborty
Current driver uses FW API version 2 and thus code corresponding to FW API version 1 has become obsolete. Clean up this from the driver. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29qlcnic: fail when try to setup unsupported featuresStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23qlcnic: update version to 5.0.6Amit Kumar Salecha
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23qlcnic: mark context state freed after destroyAmit Kumar Salecha
After destroying recv ctx, context state remain same. Fix it by marking as FREED. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23qlcnic: offload tx timeout recoveryAmit Kumar Salecha
Offload tx timeout recovery to fw recovery func(check_health). In check_health, first check health of device, if it its ok, then do tx timeout recovery otherwise device recovery. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23qlcnic: dont free host resources during fw recoveryAmit Kumar Salecha
There is no need to free/alloc host resources during firmware recovery. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23qlcnic: release device resources during interface downAmit Kumar Salecha
Previously we were allocating device resources during probe and release them during remove. Now alloc during interface up and release in interface down. This helps in device performance, as it doesn't need to keep track of inactive resources. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23qlcnic: fix mac address mgmtAmit Kumar Salecha
We first add mac address in driver local list and then send command to fw to add same. There are checks in driver to ensure send command doesn't fail before adding mac address in local list. But instead fix should be: Add mac address in fw and if it succeeds, add it in driver local list. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23qlcnic: handshake with card after fw loadAmit Kumar Salecha
Instead of delaying rcv handshake till interface comes up, do it just after fw load. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23qlcnic: cleanup skb allocationAmit Kumar Salecha
No need to maintian separate state for alloced and freed skb. This can be done by null check. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-17qlcnic: fix register accessAmit Kumar Salecha
For certain set of register, base window addresses are not defined. In such cases window should not set. Return with error for such cases to avoid NMI. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-17qlcnic: fix race in tx stop queueRajesh K Borundia
There is a race between netif_stop_queue and netif_stopped_queue check. So check once again if buffers are available to avoid race. With above logic we can also get rid of tx lock in process_cmd_ring. Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-17qlcnic: seperate interrupt for TXschacko
Earlier all poll routine can process rx and tx, But now one poll routine to process rx + tx and other for rx only. Last msix vector will be used for separate tx interrupt. o This is supported from fw version 4.4.2. o Bump version 5.0.5 Signed-off-by: Sony Chacko <schacko@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-17qlcnic: change driver descriptionSritej Velaga
o Remove extra printing of mac address o This driver also supports NIC only Qlogic adapters. Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-17qlcnic: fix device soft resetSucheta Chakraborty
During device soft reset, don't halt every device block. Access to some blocks is required during recovery. Signed-off-by: Sucheta Chakraborty <sucheta@dut4145.unminc.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-16qlcnic: Bumped up version numberAnirban Chakraborty
Changed the driver version number to 5.0.4 Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-16qlcnic: Fix a bug in setting up NIC partitioning modeAnirban Chakraborty
The driver was not detecting the presence of NIC partitioning capability of the firmware properly. Now, it checks the eswitch set bit in the FW capabilities register and accordingly sets the driver mode as NPAR capable or not. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-03qlcnic: Fix Compilation Issue when CONFIG_INET was not setAnirban Chakraborty
Original code was placed incorrectly inside a block of code marked with CONFIG_INET directive. Fix by moving it outside. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Tested-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02qlcnic: NIC Partitioning - Add non privileged mode supportAnirban Chakraborty
Added support for NIC functions that work in non privileged mode where these functions are privileged to do IO only, the control operations are handled via privileged functions. Bumped up version number to 5.0.3. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02qlcnic: NIC Partitioning - Add basic infrastructure supportAnirban Chakraborty
Following changes have been added to enable the adapter to work in NIC partitioning mode where multiple PCI functions of an adapter port can be configured to work as NIC functions. The first function that is enumerated on the PCI bus assumes the role of management function which, besides being able to do all the NIC functionality, can configure other NIC partitions. Other NIC functions can be configured as privileged or non privileged functions. Privileged function can not configure other NIC functions but can do all the NIC functionality including any firmware initialization, chip reset etc. Non privileged functions can do only basic IO. For chip reset etc, it depends on the privilege or management function. 1. Added code to determine PCI function number independent of kernel API. 2. Added Driver - FW version 2.0 support. 3. Changed producer and consumer register offset calculation. 4. Added management and privileged operation modes for npar functions. A module parameter has been added to control it. 5. Added support for configuring the eswitch in the adapter. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-21sysfs: add struct file* to bin_attr callbacksChris Wright
This allows bin_attr->read,write,mmap callbacks to check file specific data (such as inode owner) as part of any privilege validation. Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-17qlcnic: mark device state failAmit Kumar Salecha
Device state need to be mark as FAILED, if fail to start firmware. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17qlcnic: remove unused registerAmit Kumar Salecha
Removing register defines which are not used by Qlgoic CNA device. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17qlcnic: fix internal loopback testSucheta Chakraborty
Reset/set DEV_UP bit during allocation and deallocation of resources. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17qlcnic: module param for firmware load optionAmit Kumar Salecha
By default fw is loaded from flash, user can change this priority using load_fw_file module param. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17qlcnic: fix rx bytes statisticsSucheta Chakraborty
Added lrobytes to it. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17qlcnic: change adapter name displaySucheta Chakraborty
Append mac address to adapter name. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17qlcnic: fix memory leaksAnirban Chakraborty
Fixes memory leak in error path when memory allocation for adapter data structures fails. Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14qlcnic: add idc debug registersSucheta Chakraborty
When ever driver changes the device state, it should write pci-func number and timestamp in debug registers. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14qlcnic: support quisce modeSucheta Chakraborty
Device can go to quiescent state, during which drivers should refrain from using the device. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14qlcnic: check device classSucheta Chakraborty
pci-func class can be other than ethernet in Qlogic CNA device. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-26 17:53:45 +0000