Age | Commit message (Collapse) | Author |
|
Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver supports Autoneg and at least MII. Tell the PHY
that to avoid any confusion in the PHY code.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to check for the address being a multicast address in
the netdev_for_each_mc_addr loop, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables software (and phy device) transmit time stamping.
Compile tested only.
Cc: Shlomi Gridish <gridish@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of users of of_platform_driver in drivers/net. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
|
|
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
This script:
while [ 1==1 ] ; do ifconfig eth0 up; usleep 1950000 ;ifconfig eth0 down; dmesg -c ;done
causes in just a second or two:
INFO: task ifconfig:572 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
ifconfig D 0ff65760 0 572 369 0x00000000
Call Trace:
[c6157be0] [c6008460] 0xc6008460 (unreliable)
[c6157ca0] [c0008608] __switch_to+0x4c/0x6c
[c6157cb0] [c028fecc] schedule+0x184/0x310
[c6157ce0] [c0290e54] __mutex_lock_slowpath+0xa4/0x150
[c6157d20] [c0290c48] mutex_lock+0x44/0x48
[c6157d30] [c01aba74] phy_stop+0x20/0x70
[c6157d40] [c01aef40] ucc_geth_stop+0x30/0x98
[c6157d60] [c01b18fc] ucc_geth_close+0x9c/0xdc
[c6157d80] [c01db0cc] __dev_close+0xa0/0xd0
[c6157d90] [c01deddc] __dev_change_flags+0x8c/0x148
[c6157db0] [c01def54] dev_change_flags+0x1c/0x64
[c6157dd0] [c0237ac8] devinet_ioctl+0x678/0x784
[c6157e50] [c0239a58] inet_ioctl+0xb0/0xbc
[c6157e60] [c01cafa8] sock_ioctl+0x174/0x2a0
[c6157e80] [c009a16c] vfs_ioctl+0xcc/0xe0
[c6157ea0] [c009a998] do_vfs_ioctl+0xc4/0x79c
[c6157f10] [c009b0b0] sys_ioctl+0x40/0x74
[c6157f40] [c00117c4] ret_from_syscall+0x0/0x38
The reason appears to be ucc_geth_stop meets adjust_link as the
PHY reports PHY changes. I belive adjust_link hangs somewhere,
holding the PHY lock, because ucc_geth_stop disabled the
controller HW.
Fix is to stop the PHY before disabling the controller.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ucc_geth_close lacks a cancel_work_sync(&ugeth->timeout_work)
to stop any outstanding processing of TX fail. However, one
can not call cancel_work_sync without fixing the timeout function
otherwise it will deadlock. This patch brings ucc_geth in line with
gianfar:
Don't bring the interface down and up, just reinit controller HW
and PHY.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two identical implementations of of_get_mac_address(), one
each in arch/powerpc/kernel/prom_parse.c and
arch/microblaze/kernel/prom_parse.c. Move this function to a new
common file of_net.{c,h} and adjust all the callers to include the new
header.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
[grant.likely@secretlab.ca: protect header with #ifdef]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
|
|
This patch contains a fix for UCC device number in verbose debug message.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.
Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
net/ipv4/ip_output.c
|
|
This patch implements a proper modification of RX skb buffers before
recycling. Adjusting only skb->data is not enough because after that
skb->tail and skb->len become incorrect.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ioctl operation (ndo_do_ioctl) is added to make mii-tools work
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
|
|
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
Documentation/filesystems/proc.txt
arch/arm/mach-u300/include/mach/debug-macro.S
drivers/net/qlge/qlge_ethtool.c
drivers/net/qlge/qlge_main.c
drivers/net/typhoon.c
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
Old method only set tbi-phy for eth0.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 7583605b6d29f1f7f6fc505b883328089f3485ad ("ucc_geth: Fix empty
TX queue processing") fixed empty TX queue mishandling, but didn't
account another corner case: when TX queue becomes full.
Without this patch the driver will stop transmiting when TX queue
becomes full since 'bd == ugeth->txBd[txQ]' actually checks for
two things: queue empty or full.
Let's better check for NULL skb, which unambiguously signals an empty
queue.
Signed-off-by: Jiajun Wu <b06378@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sometimes ucc_geth fails to suspend with the following trace:
ucc_geth e0103000.ucc: suspend
ucc_geth e0102000.ucc: suspend
NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at net/sched/sch_generic.c:255
NIP: c021cb5c LR: c021cb5c CTR: c01ab4b4
[...]
NIP [c021cb5c] dev_watchdog+0x298/0x2a8
LR [c021cb5c] dev_watchdog+0x298/0x2a8
Call Trace:
[c0389da0] [c021cb5c] dev_watchdog+0x298/0x2a8 (unreliable)
[c0389e00] [c0031ed8] run_timer_softirq+0x16c/0x1dc
[c0389e50] [c002c638] __do_softirq+0xa4/0x11c
[...]
This patch fixes the issue by properly detaching the device on
suspend, and attaching it back on resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If PHY doesn't have an IRQ, phylib would poll for link changes, and
would call adjust_link() every second. In that case we disable and
enable the controller every second.
Let's better check if there is actually anything changed, and, if so,
change the MAC settings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 864fdf884e82bacbe8ca5e93bd43393a61d2e2b4 ("ucc_geth:
Fix hangs after switching from full to half duplex") ucc_geth driver
disables the controller during MAC configuration changes. Though,
disabling the controller might take quite awhile, and so the netdev
watchdog might get upset:
NETDEV WATCHDOG: eth2 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at c02729a8 [verbose debug info unavailable]
NIP: c02729a8 LR: c02729a8 CTR: c01b6088
REGS: c0451c40 TRAP: 0700 Not tainted (2.6.32-trunk-8360e)
[...]
NIP [c02729a8] dev_watchdog+0x280/0x290
LR [c02729a8] dev_watchdog+0x280/0x290
Call Trace:
[c0451cf0] [c02729a8] dev_watchdog+0x280/0x290 (unreliable)
[c0451d50] [c00377c4] run_timer_softirq+0x164/0x224
[c0451da0] [c0032a38] __do_softirq+0xb8/0x13c
[c0451df0] [c00065cc] do_softirq+0xa0/0xac
[c0451e00] [c003280c] irq_exit+0x7c/0x9c
[c0451e10] [c00640c4] __ipipe_sync_stage+0x248/0x24c
[...]
This patch fixes the issue by detaching the netdev during the
time we change the configuration.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following oops was seen with the ucc_geth driver:
Unable to handle kernel paging request for data at address 0x00000058
Faulting instruction address: 0xc024f2fc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c024f2fc] skb_recycle_check+0x14/0x100
LR [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
Call Trace:
[df857d50] [c000b03c] __ipipe_grab_irq+0x3c/0xa4 (unreliable)
[df857d60] [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
[df857dd0] [c0258cf8] net_rx_action+0xf8/0x1b8
[df857e10] [c0032a38] __do_softirq+0xb8/0x13c
[df857e60] [c00065cc] do_softirq+0xa0/0xac
[...]
This is because ucc_geth_tx() tries to process an empty queue when
queues are logically stopped. Stopping the queues doesn't disable
polling, and since nowadays ucc_geth_tx() is actually called from
the polling routine, the oops above might pop up.
Fix this by removing 'netif_queue_stopped() == 0' check.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
tree-wide: fix misspelling of "definition" in comments
reiserfs: fix misspelling of "journaled"
doc: Fix a typo in slub.txt.
inotify: remove superfluous return code check
hdlc: spelling fix in find_pvc() comment
doc: fix regulator docs cut-and-pasteism
mtd: Fix comment in Kconfig
doc: Fix IRQ chip docs
tree-wide: fix assorted typos all over the place
drivers/ata/libata-sff.c: comment spelling fixes
fix typos/grammos in Documentation/edac.txt
sysctl: add missing comments
fs/debugfs/inode.c: fix comment typos
sgivwfb: Make use of ARRAY_SIZE.
sky2: fix sky2_link_down copy/paste comment error
tree-wide: fix typos "couter" -> "counter"
tree-wide: fix typos "offest" -> "offset"
fix kerneldoc for set_irq_msi()
spidev: fix double "of of" in comment
comment typo fix: sybsystem -> subsystem
...
|
|
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MPC8360 QE UCC ethernet controllers hang when changing link duplex
under a load (a bit of NFS activity is enough).
PHY: mdio@e0102120:00 - Link is Up - 1000/Full
sh-3.00# ethtool -s eth0 speed 100 duplex half autoneg off
PHY: mdio@e0102120:00 - Link is Down
PHY: mdio@e0102120:00 - Link is Up - 100/Half
NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at c01fcbd0 [verbose debug info unavailable]
NIP: c01fcbd0 LR: c01fcbd0 CTR: c0194e44
...
The cure is to disable the controller before changing speed/duplex
and enable it afterwards.
Though, disabling the controller might take quite a while, so we
better not grab any spinlocks in adjust_link(). Instead, we quiesce
the driver's activity, and only then disable the controller.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We'll need ugeth_disable() and ugeth_enable() calls earlier in the
file, so rearrange some code to avoid forward declarations.
The patch doesn't contain any functional changes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/yellowfin.c
|
|
This patch implements suspend/resume and WOL support for UCC Ethernet
driver.
We support two wake up events: wake on PHY/link changes and wake
on magic packet.
In some CPUs (like MPC8569) QE shuts down during sleep, so magic packet
detection is unusable, and also on resume we should fully reinitialize
UCC structures.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes currently unused UGETH_MAGIC_PACKET Kconfig symbol
and code, i.e. magic_packet_detection_{enable,disable} functions.
The two functions each contain just two steps that we'll place into
suspend/resume code path under CONFIG_PM.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch factors out MAC initialization into ucc_geth_init_mac()
function that we'll use for suspend/resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NETPOLL API requires that interrupts remain disabled in
netpoll_send_skb(). The use of spin_lock_irq() and spin_unlock_irq()
in the NETPOLL API callbacks causes the interrupts to get enabled and
can lead to kernel instability.
The solution is to use spin_lock_irqsave() and spin_unlock_restore()
to prevent the irqs from getting enabled while in netpoll_send_skb().
Call trace:
netpoll_send_skb()
{
-> local_irq_save(flags)
---> dev->ndo_start_xmit(skb, dev)
---> spin_lock_irq()
---> spin_unlock_irq() *******here would enable the interrupt.
...
-> local_irq_restore(flags)
}
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/iwmc3200wifi/netdev.c
net/wireless/scan.c
|
|
Since commit 0b9da337dca972e7a4144e298ec3adb8f244d4a4 ("Rework
ucc_geth driver to use of_mdio infrastructure") the fixed-link
support is broken.
This patch fixes the support by removing !ug_info->phy_node check,
and adds a call to of_phy_connect_fixed_link() if a phy is not attached
to the MAC.
Also, remove an old fixed-link code that we don't use any longer.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can reclaim transmitted skbs to use in the receive path, so-called
skb recycling support.
Also reorder ucc_geth_poll() steps, so that we'll clean tx ring firstly,
thus maybe reclaim some skbs for rx.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (55 commits)
netxen: fix tx ring accounting
netxen: fix detection of cut-thru firmware mode
forcedeth: fix dma api mismatches
atm: sk_wmem_alloc initial value is one
net: correct off-by-one write allocations reports
via-velocity : fix no link detection on boot
Net / e100: Fix suspend of devices that cannot be power managed
TI DaVinci EMAC : Fix rmmod error
net: group address list and its count
ipv4: Fix fib_trie rebalancing, part 2
pkt_sched: Update drops stats in act_police
sky2: version 1.23
sky2: add GRO support
sky2: skb recycling
sky2: reduce default transmit ring
sky2: receive counter update
sky2: fix shutdown synchronization
sky2: PCI irq issues
sky2: more receive shutdown
sky2: turn off pause during shutdown
...
Manually fix trivial conflict in net/core/skbuff.c due to kmemcheck
|
|
-- derived from reverted commit 047584ce94108012288554a5f84585d792cc7f8f
-- reworked by Grant Likely to play nice with commit:
"net: Rework ucc_geth driver to use of_mdio infrastructure"
(0b9da337dca972e7a4144e298ec3adb8f244d4a4)
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|