| Age | Commit message (Collapse) | Author |
|---|
|
CC [M] drivers/net/wireless/ath/ath6kl/cfg80211.o
drivers/net/wireless/ath/ath6kl/cfg80211.c:1838:2: warning: initialization from incompatible pointer type
Caused by commit e9f935e3e8dc0bddd0df6d148165d95925422502...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
the AR_SREV register does not seems to indicate whether AR9480 is
pci_express capable or not though the other information like macVersion
etc can be obtained properly. this fix is essential as ASPM won't be intialized
and its related driver functionality ath9k_hw_configpcipowersave won't be
called
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
this patch fixes the assumption of maximum number of GPIO pins present
in AR9287/AR9300. this fix is essential as we might encounter some
functionality issues involved in accessing the status of GPIO pins which
are all incorrectly assumed to be not within the range of max_num_gpio
of AR9300/AR9287 chipsets
Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.
The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
ops.conf_tx = conf_tx_op;
@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
conf_tx_op (
- struct ieee80211_hw *hw,
+ struct ieee80211_hw *hw, struct ieee80211_vif *vif,
u16 queue,
const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
this extends the bits for rf kill GPIO selection to [7:2] from [4:2] as
we use GPIO pin 11 as rfkill for AR9480 and also remove few unused
macros
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: "Hu, Russell" <rhu@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This was reported and tested by Martin Walter over at AVM GmbH Berlin.
This also applies to 3.0.1 so sendint to stable.
Cc: s.kirste@avm.de
Cc: d.friedel@avm.de
Cc: Martin Walter <m.walter@avm.de>
Cc: Peter Grabienski <pgrabien@qca.qualcomm.com>
Cc: stable@kernel.org
Tested-by: Martin Walter <m.walter@avm.de>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
|
|
Fixes compilation errors when compiling for ARM:
ath6kl/debug.c:312: error: implicit declaration of function 'vmalloc'
ath6kl/debug.c:312: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:342: error: implicit declaration of function 'vfree'
ath6kl/debug.c:696: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:871: warning: assignment makes pointer from integer without a cast
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
My earlier debug log additions added these warnings when compiling 64 bit
kernels:
ath6kl/init.c:962: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:975: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:988: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:1009: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:1192: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
ath6kl/init.c:1236: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
ath6kl/init.c:1267: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
Reported-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
For uAPSD implementation, it is necessary to know on
which ACs frames are buffered. mac80211 obviously
knows about the frames it has buffered itself, but
with aggregation many drivers buffer frames. Thus,
mac80211 needs to be informed about this.
For now, since we don't have APSD in any form, this
will unconditionally set the TIM bit for the station
but later with uAPSD only some ACs might cause the
TIM bit to be set.
ath9k is the only driver using this API and I only
modify it in the most basic way, it won't be able
to implement uAPSD with this yet. But it can't do
that anyway since there's no way to selectively
release frames to the peer yet.
Since drivers will buffer frames per TID, let them
inform mac80211 on a per TID basis, mac80211 will
then sort out the AC mapping itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k_hw_gpio_get reads the GPIO in/out registers to get the status of
GPIO pins, so use PS wrappers
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Make use of the rx status's is_mybeacon in order to avoid
redundant memcmp.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fill the ampdu_[ack]_len for both aggregation and normal frames.
So that we could avoid unnecesary conditional at tx status.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Otheriwse the module.h split up fails like this:
drivers/net/wireless/ath/ath6kl/init.c:27:26: error: expected ')' before 'uint'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add a new debug level ATH6KL_DBG_WMI_DUMP and other minor
improvements to the wmi debug messages.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Just to make it easier to find out why boot fails.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add extensive debug messages to sdio.c. Makes it easier to debug
various problems.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Makes it easier to recognise longs dumps.
Obligatory screenshot using "rx" prefix:
ath6kl: ath6kl_rx
rx 00000000: 10 10 00 00 00 00 08 30 00 00 00 00 00 00 f9 0b .......0........
rx 00000010: 2c 44 08 30 00 00 f9 0b 0c a4 02 00 00 00 73 d2 ,D.0..........s.
rx 00000020: 94 00 f9 0b 04 8c 01 00 02 00 07 02 02 00 f9 0b ................
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
For some reason firmware is sending invalid rates when we try to
query current bitrate from ath6kl_get_station() and a warning is issued:
[ 3810.415720] ath6kl: invalid rate: 1935633515
[ 3811.105493] ath6kl: invalid rate: 1935633515
[ 3811.556063] ath6kl: invalid rate: 1935633515
As the warning happens way too often, convert the warning to a debug
message once we have a proper fix. But to make it easy to follow
how often the problem appears, add a debugfs to print
various statistics about workarounds and make this issue the first WAR.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Conflicts:
drivers/net/wireless/iwlwifi/iwl-scan.c
net/wireless/nl80211.c
|
|
After 'ath9k: optimize ath9k_ps_restore', it would only send the device to
network sleep and not to full sleep anymore, potentially causing more
battery drain.
Reported-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.
Update all the drivers that implement these callbacks.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
this represents the bitmap of block ACK received after the
successful transmission of an aggregate frame. also made few
changes to beautify the display
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In some firmware versions their patch address has changed. If the firmware
provides one, use it to override the default address.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Commit 94e532d1a ("ath6kl: Fix system freeze under heavy data load")
aligns the skb data without checking if the skb is cloned. Because of
this ath6kl can corrupt the local TCP stack information that can result
in TCP retransmission failing and TCP connections stalling.
To avoid the corruption we need to copy the skb. Now the alignment
in ath6kl_htc_tx_buf_align() doesn't corrupt TCP packets anymore (and is
not even used for the cloned skb's that got copied since the alignment
of the data is handled at the copy time).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
ath6kl_htc_tx_setup_scat_list()
It is unnecessary to take the first list entry from queue again for
transmission. Sometimes it may look racy when the head of the list
changes between subsequent retrival, but should not happen in
practical.
Reported-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
drivers/net/wireless/ath/ath6kl/htc_hif.o:
In function `ath6kl_debug_fwlog_event':
drivers/net/wireless/ath/ath6kl/debug.h:109:
multiple definition of `ath6kl_debug_fwlog_event'
drivers/net/wireless/ath/ath6kl/debug.o:
drivers/net/wireless/ath/ath6kl/debug.h:109: first defined here
drivers/net/wireless/ath/ath6kl/htc_hif.o:
In function `ath6kl_debug_cleanup':
drivers/net/wireless/ath/ath6kl/debug.h:118:
multiple definition of `ath6kl_debug_cleanup'
drivers/net/wireless/ath/ath6kl/debug.o:
drivers/net/wireless/ath/ath6kl/debug.h:118: first defined here
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
proper dma_unmapping and freeing of skb's has to be done in the rx
cleanup for EDMA chipsets when the device is unloaded and this also
seems to address the following warning which shows up occasionally when
the device is unloaded
Call Trace:
[<c0148cd2>] warn_slowpath_common+0x72/0xa0
[<c03b669c>] ? dma_debug_device_change+0x19c/0x200
[<c03b669c>] ? dma_debug_device_change+0x19c/0x200
[<c0148da3>] warn_slowpath_fmt+0x33/0x40
[<c03b669c>] dma_debug_device_change+0x19c/0x200
[<c0657f12>] notifier_call_chain+0x82/0xb0
[<c0171370>] __blocking_notifier_call_chain+0x60/0x90
[<c01713bf>] blocking_notifier_call_chain+0x1f/0x30
[<c044f594>] __device_release_driver+0xa4/0xc0
[<c044f647>] driver_detach+0x97/0xa0
[<c044e65c>] bus_remove_driver+0x6c/0xe0
[<c029af0b>] ? sysfs_addrm_finish+0x4b/0x60
[<c0450109>] driver_unregister+0x49/0x80
[<c0299f54>] ? sysfs_remove_file+0x14/0x20
[<c03c3ab2>] pci_unregister_driver+0x32/0x80
[<f92c2162>] ath_pci_exit+0x12/0x20 [ath9k]
[<f92c8467>] ath9k_exit+0x17/0x36 [ath9k]
[<c06523cd>] ? mutex_unlock+0xd/0x10
[<c018e27f>] sys_delete_module+0x13f/0x200
[<c02139bb>] ? sys_munmap+0x4b/0x60
[<c06547c5>] ? restore_all+0xf/0xf
[<c0657a20>] ? spurious_fault+0xe0/0xe0
[<c01832f4>] ? trace_hardirqs_on_caller+0xf4/0x180
[<c065b863>] sysenter_do_call+0x12/0x38
---[ end trace 16e1c1521c06bcf9 ]---
Mapped at:
[<c03b7938>] debug_dma_map_page+0x48/0x120
[<f92ba3e8>] ath_rx_init+0x3f8/0x4b0 [ath9k]
[<f92b5ae4>] ath9k_init_device+0x4c4/0x7b0 [ath9k]
[<f92c2813>] ath_pci_probe+0x263/0x330 [ath9k]
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Driver does not report disconnect event properly when in connecting state,
this leads to issues failures in starting reconnection. Send a disconnect
command to target when a disconnect event is received with reason code
other than 3 (DISCONNECT_CMD - disconnect request from host) to make the
frimware stop trying to connect even after giving disconnect event. There
will be one more disconnect event for this disconnect command with reason
code DISCONNECT_CMD which will be notified to cfg80211.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When pinging form ar6003 to the AP RTT was high even when power save was
disabled:
100 packets transmitted, 97 received, 3% packet loss, time 99125ms
rtt min/avg/max/mdev = 1.875/46.733/795.506/139.181 ms
After some investigation one reason for this was that received
multicast traffic confused the aggrecation logic and caused 400 ms
timeouts when receiving multicast frames from AP.
A simple way to fix is to pass only unicast frames for aggregation. This
improves RTT:
100 packets transmitted, 99 received, 1% packet loss, time 99144ms
rtt min/avg/max/mdev = 2.083/13.084/403.390/56.794 ms
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This allows RSN pre-authentication to be used when roaming decisions are
done in the target.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When the rssi of the current AP drops, both wpa_supplicant and the
firmware may do a background scan to find a better AP and try to
associate. This might lead to a race condition where both may try
to connect to some AP based on their scan results.
Since the firmware is capable of handling roaming, let
wpa_supplicant know about this capability so that it will back off
from bgscan based roaming.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
|
|
Now that we allow the first Beacon frame after each connection to
be processed at the host, we can figure out the DTIM period and
expose it with Beacon interval through STA info BSS parameters
to user space.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Since we may end up using a dummy BSS entry when roaming, allow one Beacon
frame -based bssinfo from the current BSS to be processed prior to starting
to filter all bssinfo events. This allows cfg80211 BSS table to be filled
with proper data in the roaming case where the full Beacon data may not
have been present at the time of roamed event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
There is no point in unconditionally converting the bssinfo header
to the old version since only the new header is being used and the
driver can as well read the values from it when needed. Leaving out
the conversion saves some extra memory copying.
In addition, use the calculated "rssi" value snr - 95 dBm to get the
proper value in cfg80211 BSS table (i.e., something that more or less
matches with the value used in STA info).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Now that the scan results are reported directly to the cfg80211 BSS
table there is no need for maintaining this internal node table
implementation for scan results. Remove the definitions and node
table functions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The internal node table in ath6kl was not really used for any useful
purpose. It was just used to collect scan results during a scan and then
provide them in a burst to cfg80211 at the completion of the scan. There
is no point in doing this since cfg80211 is perfectly capable of
maintaining the BSS table and the BSS inform messages are sent in
separate function calls anyway.
This provides more complete information in the cfg80211 BSS table since
this allows Beacon and Probe Response frames to be distinguished and IEs
from them reported separately.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Since ath6kl does not actually update cfg80211 BSS table when this
event occurs, there is not much need for removing the entries from
the internal table that is not really used or exposed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
ath6kl does not actually update cfg80211 BSS table when this update
occurs, so there is not much need in updating the internal table
that is not used or exposed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This event has been deprecated and there is no need for ath6kl to
include code for processing it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This fixes the BSS "update" just before the connected or roamed event.
The previous implementation was completely broken: it forced a hardcoded
signal strength and IEs from Association _Request_ frame instead of any
Beacon information. This broke various things, including PMKSA caching.
The current workaround for creating a dummy BSS entry before the roamed
event is not exactly ideal, but that is quite a bit better than the
previous state. As a future improvement, cfg80211 could potentially be
extended to allow this type of use or ath6kl could delay sending the
roamed event before receiving a BSS info event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
During the endurance testing, rx frames are not getting DMAd from
MAC whereas pcu rx frame counters are getting updated properly.
As per systems team input updated the initval to fix rx dma stuck
issue.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
CCK/OFDM noise immunilty values are always reset to defaults
during bgscan. This could affect the link quality and
performance when the STA is associated in a noisy channel.
So do not override the learned values across the scanning.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Conflicts:
drivers/net/wireless/iwlwifi/iwl-pci.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-tx.c
drivers/net/wireless/rt2x00/rt2800usb.c
drivers/net/wireless/wl12xx/main.c
|
|
Not doing so, the caldata continues to retain older history
values learned on that channel. It is always safer to start
noise floor calibration from the defaults after the assoication.
So this patch resets the nf history buffer when none of the
STA vifs are associated.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently during the full reset, the nf calibration is always
restarted from the defaults. The noise floor history buffers are
never be used again after the scan and ath reset. This patch
ensures that nf histories are always be used that helps to
improve the signal quality on congested environment
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Do the magnitude/phase coeff correction only if the outlier
is detected. Updating wrong magnitude/phase coeff factor
impacts not only tx gain setting but also leads to poor
performance in congested networks. In the clear environment
the impact is very minimal because the outlier happens
very rarely according to the past experiment. It occured
less than once every 1000 calibrations.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AR913x uses the same PLL register layout as AR9160 and later.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k_hw_set_diversity is only called from init.c where it cannot affect
the hardware setting because it's cleared on the next reset.
Instead of using a PHY op for something that's supposed to be initialized
statically, set the register value directly in the INI override function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
