summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath
AgeCommit message (Collapse)Author
2014-03-31Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
2014-03-27carl9170: Remove casts of pointer to same typeJoe Perches
Casting a pointer to a pointer of the same type is pointless, so remove these unnecessary casts. Done via coccinelle script: $ cat typecast_2.cocci @@ type T; T *foo; @@ - (T *)foo + foo Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-25Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: Documentation/devicetree/bindings/net/micrel-ks8851.txt net/core/netpoll.c The net/core/netpoll.c conflict is a bug fix in 'net' happening to code which is completely removed in 'net-next'. In micrel-ks8851.txt we simply have overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-21Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
2014-03-17wil6210: fix race between disconnect and Tx NAPIVladimir Kondratiev
When disconnecting some CID, corresponded Tx vring get released. During vring release, all descriptors get freed. It is possible that Tx NAPI working on the same vring simultaneously. If it happens, descriptor may be double freed. To protect from the race above, make sure NAPI won't process the same vring. Introduce 'enabled' flag in the struct vring_tx_data. Proceed with Tx NAPI only if 'enabled' flag set. Prior to Tx vring release, clear this flag and make sure NAPI get synchronized. NAPI enablement status protected by wil->mutex, add protection where it was missing and check for it. During reset, disconnect all peers first, then proceed with the Rx vring. It allows for the disconnect flow to observe proper 'wil->status' and correctly notify cfg80211 about connection status change Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: add memory barriers for the reset flowVladimir Kondratiev
make sure reset flow executed in order Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: target reset flow updateVladimir Kondratiev
Use 'real' indication for hardware state. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: use GROVladimir Kondratiev
GRO is easy to enable when already using NAPI framework, and it improves CPU utilisation. Enable it by default. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: serialize fw_recovery and start_apVladimir Kondratiev
These methods can change device state, serialize with others similar ones like up/down Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fix secondary connectVladimir Kondratiev
when STA receiving connect() when already connected, it should return error Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fw error recoveryVladimir Kondratiev
upon fw error interrupt - in STA mode, disconnect/cancel scan and then reset FW/HW added module param - no_fw_recovery which is false by default Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: Fix kernel oops in reset flowVladimir Kondratiev
wil_reset() removes vring's At the same time NAPI may be active performing Rx/Tx completion. If this happens, Rx/Tx polling functions going to access already removed vrings Make sure NAPI is idle and won't be started prior to vring removal. For this, track NAPI enabled state Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fix memory leak in the AP flowVladimir Kondratiev
When switching between STA and AP modes, memory allocated for Rx vring leaks This is because start_ap() allocates Rx vring but stop_ap() do not free it. Logically, Rx vring is not valid (HW can't use it anymore), so free it in reset() Also, check double init for Rx vring and bail out with -EINVAL Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: reduce printingVladimir Kondratiev
Convert 2 often printed messages to dynamic ones Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: reset on power goodVladimir Kondratiev
Configure hardware to perform full reset on "power good". This mean, reset HW on system boot. This improves card stability. By default this is off. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: sort HW registers definitionsVladimir Kondratiev
Put all registers in order for easier navigation; fix naming to reflect hardware cluster Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fix for HW bug in interrupt setup logicVladimir Kondratiev
Hardware bug triggered by the MSI init while INTx asserted for some reason. De-assert INTx prior to MSI set-up Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: report reset timeVladimir Kondratiev
Useful to detect hardware problems Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: reduce dmesg pollution after FW crashVladimir Kondratiev
When FW crashes, dmesg get polluted with the "FW not ready" error message. Print it only once per FW lifecycle Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: update target reset to support new HWVladimir Kondratiev
Support for new chip revision. Revision read from the internal register, PCIE config's "revision id" register do not indicate HW version properly Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: generalize tx desc mappingVladimir Kondratiev
Introduce enum to describe mapping type; allow 'none' in addition to 'single' and 'page'; this is preparation for GSO Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: add scatter-gather supportVladimir Kondratiev
When setting fragmented skb for Tx, assign skb to the last descriptor and set number of fragments in the 1-st one On Tx complete, HW sets "DU" bit in Tx descriptor only for the last descriptor; so search for it using number of fragments field. Middle descriptors may have "DU" bit not set by the hardware. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: enable scan while connectedVladimir Kondratiev
New firmware do support scan while connected. Enable it. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: Block data till "data port open" reportedVladimir Kondratiev
When connection established, as reported by WMI_CONNECT_EVENTID, 4-way handshaking required for the secure connection is not done yet. It is indicated by another WMI event. Wait for it and only then allow data traffic. In case of non-secure connection, FW reports "data port open" immediately after connection. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: Helpers to deal with 'cidxtid' fieldsVladimir Kondratiev
Encode/decode helpers Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k: Fix temperature compensationSujith Manoharan
The registers for temperature compensation need to be programmed only for active chains. Use the TX chainmask to make sure that this is done properly for QCA953x. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k: Disable AR_INTR_SYNC_HOST1_FATAL for QCA953xSujith Manoharan
Along with AR9340 and AR955x, this is also needed for the QCA953x SoC. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k: Add QCA953x WMAC platform supportSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: move DEFAULT_SWBA_RESPONSE check to ath9k_htc_beacon_initOleksij Rempel
... to remove some more dups. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: use ath9k_cmn_beacon_config_apOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k: remove unused ath9k_get_next_tbttOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k: move ath9k_beacon_config_ap commonOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: use ath9k_cmn_beacon_config_adhocOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: use ath9k_htc_beacon_init in ath9k_htc_beacon_config_adhocOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: use ath9k_htc_beacon_init in ath9k_htc_beacon_config_apOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: add ath9k_htc_beacon_init (but not use it)Oleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k: move ath9k_beacon_config_adhoc to commonOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: use ath9k_cmn_beacon_config_staOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k: move ath9k_beacon_config_sta to common-beaconOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k-common: add nexttbtt and intval to ath_beacon_configOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k|ath9k_htc: move IEEE80211_MS_TO_TU to commonOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k: remove unused beacon_qiOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: sync beacon slot code with ath9kOleksij Rempel
we will need it for common-beacon Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k: remove unused bc_tstampOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: add ATH_OP_PRIM_STA_VIFOleksij Rempel
we will need it to make common-beacon code work. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: use common->op_flagsOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k: move sc_flags to ath_commonOleksij Rempel
we will need it for ath9k_htc, may be other drivers too Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: use ath_beacon_conf.enable_beaconOleksij Rempel
to reduce difference between ath9k and ath9k_htc Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: move beaconq to struct htc_beaconOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17ath9k_htc: use common ath_beacon_configOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-16 12:51:12 +0000