| Age | Commit message (Collapse) | Author |
|---|
|
Jumbograms are frames put together linked together through
more than one descriptor. For example ath9k_htc will use this
to send from the target a large frame split up into 2 or more
segments. The driver then would be in charge of putting the
frame back together.
When jumbograms are constructed the rx_stats->rs_more will
bet set and rx_stats->rs_status will not have any valid content
as the actual status will only be avialable at the end of
the chained descriptors.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is now deprecated and unused within mac80211, so time
to remove it as otherwise we'd be doing some unecessary
computations for nothing.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k and ath9k_htc share a lot of common hardware characteristics.
They only differ in that ath9k_htc works with a target CPU and ath9k
works directly with the hardware. ath9k_htc will do *some* things in
the firmware, but a lot of others on the host.
The common 802.11n hardware code is already shared through the ath9k_hw
module. Common helpers amongst all Atheros drivers can use the ath module,
this includes ath5k and ar9170 as users. But there is some common driver
specific helpers which are not exactly hardware code which ath9k and
ath9k_htc can share. We'll be using ath9k_common for this to avoid
bloating the ath module and the common 802.11n hardware module ath9k_hw.
We start by sharing skb pre and post processing in preparation for a hand
off to mac80211.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use a helper for the RX skb post processing,
ath9k_rx_skb_postprocess().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This will make sharing code easier between ath9k and ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
And change the return value to something more obvious.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
While at it flip the order, seems easier to read and also
add some better description as to why we do this check.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath5k is using the (csz - 1) twice as ath_rxbuf_alloc() already allocates
and moves skb->data accordingly. Remove the extra (csz -1).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This will also be used by ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The skb->cb (control buffer, 48 bytes) is available to the skb
upon skb allocation. You can fill it up imediately after skb
allocation. ath9k was copying onto the skb->cb the data from the
processed skb for mac80211 from a stack struct ieee80211_rx_status
structure. This is unnecessary, instead use the skb->cb for the
rx status immediately after the skb becomes available and DMA
synched.
Additionally, avoid the copy of the skb->cb also for virtual wiphys
as skb_copy() will copy over the skb->cb for us as well.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This moves all the RX processing of RSSI into a helper,
ath_rx_prepare(). ath_rx_prepare() should now be really
easy to read and follow.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This moves the qual computing into a small helper,
ath9k_compute_qual()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k_process_rate() now does all the rx status processing to
read the rate the hardware passed and translate it to whatever
mac80211 wants.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Its just a distraction when reading the code, instead use the
rx_stats->rs_rate directly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This does sanity checking on the skb and RX status descriptor
prior to processing.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
No need to use the private driver structure to get to an sband.
This will make it easier to share this code with ath9k_htc.
With the sc gone we can now just pass the common structure to
ath_rx_prepare().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This can be shared between ath9k and ath9k_htc. It will also
help with sharing routine helpers on the RX path.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This will be shared between ath9k and ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Its not needed, so just pass the hardware RX status.
We'll be simplfying ath_rx_prepare() with code we can share
between ath9k and ath9k_htc. This will help make that code
easier to read and manage.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k virtual wiphys all share the same internal buffer space
for TX but they do not share the mac80211 skb queues. When
ath9k detects it is running low on buffer space to TX it tells
mac80211 to stop sending it skbs its way but it always does
this only for the primary wiphy. This means mac80211 won't know
its best to avoid sending ath9k more skbs on a separate virtual
wiphy. The same issue is present for reliving the skb queue.
Since ath9k does not keep track of which virtual wiphy is hammering
on TX silence all wiphy's TX when we're low on buffer space. When
we're free on buffer space only bother informing the virtual wiphy
which is active that we have free buffers.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When using virtual wiphys the base sc->hw was being used, the correct
hw is passed along the caller already so just use that.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When ath9k virtual wiphys are used the sc->hw will not always represent
the active hw, instead we need to get it from the skb->cb private
driver area. This ensures the right hw is used to find a sta for
the TX'd skb.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We use the ieee80211_hw for radio enable/disable but the wrong
structure hw was being used in consideration for virtual wiphys
as each virtual wiphy has its own ieee80211_hw struct.
Just pass the hw struct to ensure we use the right one. This should
fix the hw used and passed for radio enable/disable. This includes
the stoping / starting of the software TX queues so mac80211 doesn't
send us data for a specific virtual wiphy. ath9k already takes care
of pausing virtual wiphys and stopping the respective queues on its
own, but this should handle the idle mac80211 conf calls as well.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
this now uses the proper hw which should mean finding the
right sta when using ath9k virtual wiphy stuff. Only
advantage I see here is getting the rssi properly updated
so the 'fix' itself isn't that great, but at least this
is correct.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath_get_virt_hw() is required on RX to determine for which virtual
wiphy an skb came in for. Instead of searching for the hw twice do
it only once.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k supports its own virtual wiphys. The hardware code
relies on the ieee80211_hw for the present interface but
with recent changes introduced the common->hw was never
updated and is required for virtual wiphys.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The way idle configuration detection was implemented as
busted due to the fact that it assumed the ath9k virtual wiphy,
the aphy, would be marked as inactive if it was not used but
it turns out an aphy is always active if its the only wiphy
present. We need to distinguish between aphy activity and
idleness so we now add an idle bool for the aphy and mark
it as such based on the passed IEEE80211_CONF_CHANGE_IDLE
from mac80211.
Previous to all_wiphys_idle would never be true when using
only one device so we never really were using
IEEE80211_CONF_CHANGE_IDLE -- we never turned the radio
off or on upon IEEE80211_CONF_CHANGE_IDLE changes as radio
changes depended on all_wiphys_idle being true either to
turn the radio on or off. Since it was always false for
one device this code was doing nothing.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/iwlwifi/iwl-1000.c
drivers/net/wireless/iwlwifi/iwl-6000.c
drivers/net/wireless/iwlwifi/iwl-core.h
|
|
Setup the GPIOs for the BenQ Joybook netbook.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add GPIO configuration for the Compaq CQ60 laptop
Reported-by: David Dreggors <ddreggors@jumptv.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We should not zero out the multicast hash when configuring
the operating mode, since a zero value means all multicast
frames will get dropped. Also, ath5k_mode_setup() gets
called after any reset, so the hash already set up in
configure_filter() is lost.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
Add LED support for a Foxconn AR242X module, found on
the Acer Aspire One models AO751h/AO531h
Signed-off-by: Keng-Yu Lin <keng-yu.lin@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we have a TODO item to make all station
management dependent on virtual interfaces, I
figured I'd start with pushing such a change
to drivers before more drivers start using the
ieee80211_find_sta() API with a hw pointer and
cause us grief later on.
For now continue exporting the old API in form
of ieee80211_find_sta_by_hw(), but discourage
its use strongly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To do this we reorder callers in order in which they are called.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Force bias is a fix for usage of AR5416 radios on the 2.4 GHz band
for orientation sensitivity. This was only partially implemented
with the ath9k_hw_decrease_chain_power() but first -- this was being
called for all chipsets which is not correct and second -- it was
missing the actual orientation code.
We now ensure to only enable force bias only for AR5416 and BUG_ON()
on other chipsets. Although ath9k_hw_decrease_chain_power() was enabled
for newer chipsets I suspect that it never ran unless the EEPROM had
ATH9K_ANT_FIXED_A or ATH9K_ANT_FIXED_B for antenna diversity.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This only differs between single-chip solutions and non single-chip
solutions.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reorders phy.c routines in the order in the order in which they are used
and also moves the spur mitigation helpers for each type of chip into phy.c
as they are RF related.
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This avoids a branch on every channel change.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This allows us to later define a callback for both.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This clarifies this is only required for external radios.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is calling an allocation and checking for it, simplify
this process in a macro.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k_hw_rfattach() was just calling a helper and this helper was
doing nothing for single-chip devices, and for non single-chip devices
it is just allocating memory for banks to program the RF registers
at a later time. Simplify this by having the hw initialization call
the rf bank allocation directly for external radios.
Also, propagate an -ENOMEM properly now upon failure.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We a huge branch for old hardware and nothing for newer
hardware. Instead of doing this just bail out early for
newer hardware.
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Document what we can about the RF analog front ends (radios)
of Atheros 802.11n devices. What should be clearer now is the
what we do for old pre AR5416 and AR5418 MAC based devices in
comparison to the modern sigle-chip 802.11n solutions.
All devices after AR9280 are single chip and require less
programming -- the RF registers no longer need to be initialized
as they all have the RF analog front end embedded together with
the MAC/BB; this includes the AR9271. Older devices such as the
ones with the AR5416 MACs (PCI) or AR5418 MACs (PCI-E) have an
external 2.4 GHz AR2133 radio or a dual band 2.4 GHz / 5 GHz
AR5133 radio. These external radios require additional programming
of the RF registers.
Clarify which parts are for what devices and which code is
shared. This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We adjust the core clock for ar9271 to 117 MHz; this also
requires us to adjust the baud divider based on the targetted
baud rate.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
