| Age | Commit message (Collapse) | Author |
|---|
|
queue == __AR9170_NUM_TXQ would cause a bug on the next line.
found by Smatch ( http://repo.or.cz/w/smatch.git ).
Cc: stable@kernel.org
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When ar9170-2.fw was missing, the driver erroneously complained
about missing the initialization values file ar9170-1.fw...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Incorrect limits leads to reads outside array bounds.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Two users of ar9170 devices have now reported their cards
have been programmed with a regulatory domain of 0x8000.
This is not a valid regulatory domain as such these users were
unable to use these devices. Since this doesn't seem to be
a device EEPROM corruption we must treat it specially. It
may have been possible the manufacturer intended to use 0x0
as the regulatory domain and that would ultimately yield
to US but since we cannot get confirmationf or this we
default this special case to one of our world regulatory
domains, specifically 0x64.
Reported-by: DavidFreeman on #linux-wireless
Reported-by: Joerg Albert <jal2@gmx.de>
Cc: Christian Lamparter <chunkeey@web.de>,
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Tony Yang <tony.yang@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For AP mode we must tune ANI specially for 2 GHz and
for 5 GHz. We mask in only the flags we want to toggle
on ath9k_hw_ani_control() through the ah->ani_function
bitmask, this will take care of ignoring changes during
ANI reset which we were disabling before.
Testedy-by: Steven Luo <steven@steven676.net>
Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com>
Cc: Jouni Malinen <jouni.malinen@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pavel Roskin reported some issues with using AP mode without
nohwcrypt=1. Most likely this is similar to the problem fixed
some time ago in ath9k by 3f53dd64f192450cb331c0fecfc26ca952fb242f,
"ath9k: Fix hw crypto configuration for TKIP in AP mode."
That only affects TKIP but it's easiest to just disable that and
WEP too until we get a proper fix in.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Atheros top level menu needs a "depends WLAN_80211" to properly indent
within menuconfig and xconfig interfaces.
This is purely a visual issue but it effects all subsequent drivers.
The issue is the top level menu does not include a dependency on
WLAN_80211 so within the tree structure, Atheros is at the same level as
WLAN_80211 but when WLAN_80211 collapsed, the menu disappears along with
all subsequent drives, so it is really a subordinate.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When we reclaim the tx desc, we always assume that the
last desc is a holding desc, which is not true, and skip it.
If the tx queue is drained during channel change, internal
reset and etc, the last descriptor may not be the holding
descriptor and we fail to reclaim them. This results in the
following two issues.
1. Tx stuck - We drop all the frames coming from upper layer
due to shortage in tx desc.
2. Crash - If we fail to reclaim a tx descriptor, we miss to
update the tx BA window with the seq number of the frame
associated to that desc, which, at some point, result in
the following crash due to an assert failure in ath_tx_addto_baw().
This patch fixes these two issues.
kernel BUG at ../drivers/net/wireless/ath/ath9k/xmit.c:180!
[155064.304164] invalid opcode: 0000 [#1] SMP
Call Trace:
[<fbc6d83b>] ? ath9k_tx+0xeb/0x160 [ath9k]
[<fbbc9591>] ipv6? __ieee80211_tx+0x41/0x120 [mac80211]
[<fbbcb5ae>] ? aes_i586ieee80211_master_start_xmit+0x28e/0x560 [mac80211]
[<c037e501>] aes_generic? _spin_lock_irqsave+0x31/0x40
[<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
[<c03058b5>] ? __qdisc_run+0x1b5/0x200
[<fbbcda5a>] ? af_packetieee80211_select_queue+0xa/0x100 [mac80211]
[<c02f53b7>] ? i915dev_queue_xmit+0x2e7/0x3f0
[<fbbc9b49>] ? ieee80211_subif_start_xmit+0x369/0x7a0 [mac80211]
[<c031bc35>] ? ip_output+0x55/0xb0
[<c02e0188>] ? show_memcpy_count+0x18/0x60
[<c02eb186>] ? __kfree_skb+0x36/0x90
[<c02f2202>] ? binfmt_miscdev_queue_xmit_nit+0xd2/0x110
[<c02f347b>] ? dev_hard_start_xmit+0x16b/0x1c0
[<c03058b5>] ? __qdisc_run+0x1b5/0x200
[<c033bca7>] ? scoarp_create+0x57/0x2a0
[<c02f53b7>] ? bridgedev_queue_xmit+0x2e7/0x3f0
[<c03034a0>] ? eth_header+0x0/0xc0
[<c033b95f>] stp? arp_xmit+0x5f/0x70
[<c033bf4f>] ? arp_send+0x5f/0x70
[<c033c8f5>] bnep? arp_solicit+0x105/0x210
[<c02fa5aa>] ? neigh_timer_handler+0x19a/0x390
[<c013bf88>] ? run_timer_softirq+0x138/0x210
[<c02fa410>] ? ppdevneigh_timer_handler+0x0/0x390
[<c02fa410>] ? neigh_timer_handler+0x0/0x390
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (43 commits)
via-velocity: Fix velocity driver unmapping incorrect size.
mlx4_en: Remove redundant refill code on RX
mlx4_en: Removed redundant check on lso header size
mlx4_en: Cancel port_up check in transmit function
mlx4_en: using stop/start_all_queues
mlx4_en: Removed redundant skb->len check
mlx4_en: Counting all the dropped packets on the TX side
usbnet cdc_subset: fix issues talking to PXA gadgets
Net: qla3xxx, remove sleeping in atomic
ipv4: fix NULL pointer + success return in route lookup path
isdn: clean up documentation index
cfg80211: validate station settings
cfg80211: allow setting station parameters in mesh
cfg80211: allow adding/deleting stations on mesh
ath5k: fix beacon_int handling
MAINTAINERS: Fix Atheros pattern paths
ath9k: restore PS mode, before we put the chip into FULL SLEEP state.
ath9k: wait for beacon frame along with CAB
acer-wmi: fix rfkill conversion
ath5k: avoid PCI FATAL interrupts by restoring RETRY_TIMEOUT disabling
...
|
|
73ca5203366235f8a43e490767284ba8cfd8c479
(ath5k: remove conf->beacon_int usage)
removed bintval setting from ath5k_config. We need to init the
interval earlier and don't touch it in add_interface anymore.
Otherwise it will be set only once by upper layer through
bss_info_changed but not on second and further hostap executions.
We ended up having bintval 1000 which rendered the AP useless on
many clients.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We want to put the chip into FULL SLEEP state, when we are disabling the
radio, but the the current code always change it to AWAKE/NETWORK SLEEP.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reverts 'ath5k: remove dummy PCI "retry timeout" fix' on the
same theory as in 'ath9k: Fix PCI FATAL interrupts by restoring
RETRY_TIMEOUT disabling'.
Reported-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
An earlier commit, 'ath9k: remove dummy PCI "retry timeout" fix', removed
code that was documented to disable RETRY_TIMEOUT register (PCI reg
0x41) since it was claimed to be a no-op. However, it turns out that
there are some combinations of hosts and ath9k-supported cards for
which this is not a no-op (reg 0x41 has value 0x80, not 0) and this
code (or something similar) is needed. In such cases, the driver may
be next to unusable due to very frequent PCI FATAL interrupts from the
card.
Reverting the earlier commit, i.e., restoring the RETRY_TIMEOUT
disabling, seems to resolve the issue. Since the removal of this code
was not based on any known issue and was purely a cleanup change, the
safest option here is to just revert that commit. Should there be
desire to clean this up in the future, the change will need to be
tested with a more complete coverage of cards and host systems.
http://bugzilla.kernel.org/show_bug.cgi?id=13483
Cc: stable@kernel.org
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (55 commits)
netxen: fix tx ring accounting
netxen: fix detection of cut-thru firmware mode
forcedeth: fix dma api mismatches
atm: sk_wmem_alloc initial value is one
net: correct off-by-one write allocations reports
via-velocity : fix no link detection on boot
Net / e100: Fix suspend of devices that cannot be power managed
TI DaVinci EMAC : Fix rmmod error
net: group address list and its count
ipv4: Fix fib_trie rebalancing, part 2
pkt_sched: Update drops stats in act_police
sky2: version 1.23
sky2: add GRO support
sky2: skb recycling
sky2: reduce default transmit ring
sky2: receive counter update
sky2: fix shutdown synchronization
sky2: PCI irq issues
sky2: more receive shutdown
sky2: turn off pause during shutdown
...
Manually fix trivial conflict in net/core/skbuff.c due to kmemcheck
|
|
Many developers use "/debug/" or "/debugfs/" or "/sys/kernel/debug/"
directory name to mount debugfs filesystem for ftrace according to
./Documentation/tracers/ftrace.txt file.
And, three directory names(ex:/debug/, /debugfs/, /sys/kernel/debug/) is
existed in kernel source like ftrace, DRM, Wireless, Documentation,
Network[sky2]files to mount debugfs filesystem.
debugfs means debug filesystem for debugging easy to use by greg kroah
hartman. "/sys/kernel/debug/" name is suitable as directory name
of debugfs filesystem.
- debugfs related reference: http://lwn.net/Articles/334546/
Fix inconsistency of directory name to mount debugfs filesystem.
* From Steven Rostedt
- find_debugfs() and tracing_files() in this patch.
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Acked-by : Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reviewed-by : Steven Rostedt <rostedt@goodmis.org>
Reviewed-by : James Smart <james.smart@emulex.com>
CC: Jiri Kosina <trivial@kernel.org>
CC: David Airlie <airlied@linux.ie>
CC: Peter Osterlund <petero2@telia.com>
CC: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
CC: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If we are in PS mode, we have to process the received frame if
the SC_OP_WAIT_FOR_CAB bit is set.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We have to remain awake if the SC_OP_WAIT_FOR_CAB flag is set.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The ath9k_ps_{wakeup,restore} calls must be in balance.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This ports the ath9k rfkill code to the new API offered by
cfg80211 and thus removes a lot of useless stuff.
("With this series a kernel panic, which is a regression, during module
unload disappears." -- Vasanthakumar Thiagarajan <vasanth@atheros.com>
Other patches in the series:
ath9k: Add helper to get ath9k specific current channel
ath9k: Make sure we have current channel in ah_curchan before rf
disable/enable
-- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis Rodriguez <mcgrof@gmail.com>
Tested-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch is from Nick Kossifidis but he forgot to send it. It ensures
that the beacon queue gets started in mesh mode as well, otherwise ath5k
will not beacon in mesh point mode.
At this time, we still need to issue a scan before mesh beaconing will
work but that appears to be a separate problem.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Always enable rfkill since the ifdefs in the code is not really worth
the Kconfig option. Also fix a few code style things, and remove the
usage of the ah_gpio[] array so we can remove it later.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch along with my previous patch in mac80211 "Fix the
way ADDBA count..", fixes hang in tx when connected to an HT
AP which rejects/times out on addba req.
AGGR_ADDBA_PROGRESS should be cleared in aggr state when addba
negotiation is terminated due to either addba response is timed out
or addba is denied by the AP. With out clearing this bit,
all frames are queued onto s/w queue for getting tx'd as aggr and
will never be scheduled onto hw queue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch introduces initial rfkill support for the ath5k driver
based on rfkill support in the cfg80211 framework.
All rfkill related code is separated into newly created rfkill.c.
Changes to existing code are minimal:
* added a new data structure ath5k_rfkill to the ath5k_softc structure
* inserted calls to HW rfkill init/deinit routines
* ath5k_intr() has been extended to handle AR5K_INT_GPIO interrupts
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch is a back-port from aggregation testing code.
In the past, we didn't limit the amount of active tx urbs.
However, ar9170 only has a limited buffer reserved for
pending data frames.
This wasn't much of a problem with the slower 802.11b/g.
We simply stopped the full queue and moved on to something different
in the mean time. But - as you guessed it - this simple approach
stands in way for a decent aggregation implementation.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds new commands that the original firmware will not send
but we can use them to debug firmware.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch removes code (deprecated by "cfg80211: add rfkill support" )
main.c: In function 'ar9170_op_config':
main.c:1306: warning: '__IEEE80211_CONF_CHANGE_RADIO_ENABLED'
is deprecated (declared at include/net/mac80211.h:551)
and a useless device state.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When we remove the active interface, there's no need to continue
sending beacons; doing so would cause a null pointer deref in
ieee80211_beacon_get(). Disable the interrupt in remove_interface
and add a WARN_ON(!vif) in case there are other instances lurking.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This should help when reviewing issues regarding regulatory
domain on ath5k/ath9k/ar9170.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Handle error condition on copy_from_user() properly and
make sure a NUL terminated char[] is sent to strict_strtoul()
for proper conversion.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch completely rewrites the rfkill core to address
the following deficiencies:
* all rfkill drivers need to implement polling where necessary
rather than having one central implementation
* updating the rfkill state cannot be done from arbitrary
contexts, forcing drivers to use schedule_work and requiring
lots of code
* rfkill drivers need to keep track of soft/hard blocked
internally -- the core should do this
* the rfkill API has many unexpected quirks, for example being
asymmetric wrt. alloc/free and register/unregister
* rfkill can call back into a driver from within a function the
driver called -- this is prone to deadlocks and generally
should be avoided
* rfkill-input pointlessly is a separate module
* drivers need to #ifdef rfkill functions (unless they want to
depend on or select RFKILL) -- rfkill should provide inlines
that do nothing if it isn't compiled in
* the rfkill structure is not opaque -- drivers need to initialise
it correctly (lots of sanity checking code required) -- instead
force drivers to pass the right variables to rfkill_alloc()
* the documentation is hard to read because it always assumes the
reader is completely clueless and contains way TOO MANY CAPS
* the rfkill code needlessly uses a lot of locks and atomic
operations in locked sections
* fix LED trigger to actually change the LED when the radio state
changes -- this wasn't done before
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> [thinkpad]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
"[PATCH 3/4 v2] ar9170: fix LED power state handling" revealed
a bug which can cause a ugly crash.
The delayed worker is canceled before the LED class functions are
unregistered... So, if something manages to update the LEDs
while unregister routine is running the timer could fire _after_ the
module has been unloaded.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch contains a few more mostly random fixes for the USB front-end.
1. handle irq command response, instead of printing it to the console.
2. remove fixed FIXME.
(real fix: "ar9170usb: reset device on resume". )
3. some more one-liner.
- get rid of a useless "return;"
- add a few branch prediction hints in hot-paths
etc.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch takes care of Johannes' deadlock report by moving the
mutex_lock right after cancel_work_sync in ar9170_op_stop.
Besides, the janitor does not need to hold the mutex anymore,
so this extra lines can be removed as well.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes a minor visual bug in the led code, which
left the LED in the wrong power state when it was toggled
in a _unexpected_ way (e.g: enabling the LED twice).
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch removes a redundant flag.
.cap = IEEE80211_HT_CAP_MAX_AMSDU | \
> IEEE80211_HT_CAP_SM_PS | \ <
[...] \
> IEEE80211_HT_CAP_SM_PS, \ <
.ampdu_factor = 3, \
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes a bug in configure_filter's (sub-)routines.
We never really cleared the flags once we updated the hardware state,
so we wasted our resources by applying already active settings.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch introduces 3 new function which are used to update
the MAC state, whenever needed... e.g: after a band switch.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch replace a few constant magics which may affected
the device when operating in a 40MHz channel.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch only contains a few uncritical updates for the
hardware definition header.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes a simple copy & paste error that affected beacon
transmission in 802.11a mode.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds:
USB 0x057C:0x8401 AVM FRITZ!WLAN USB Stick N
USB 0x057C:0x8402 AVM FRITZ!WLAN USB Stick N 2.4
These devices require the 1-stage firmware, if not present we
don't continue.
Cc: Peter Grabienski <Peter.Grabienski@Atheros.com>
Cc: Stephen Chen <Stephen.Chen@Atheros.com>
Cc: Michael Fortin <Michael.Fortin@Atheros.com>
Cc: Johnny Cheng <Johnny.Cheng@Atheros.com>
Cc: Yuan-Gu Wei <Yuan-Gu.Wei@atheros.com>
Cc: Joerg Albert <jal2@gmx.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
You can get the stage 1 firmware from here:
http://www.kernel.org/pub/linux/kernel/people/mcgrof/firmware/ar9170/ar9170.fw
md5sum: 34feec4ec0eae3bb92c7c1ea2dfb4530
sha1sum: 6e5250498b815c2940d97242de31e054ae44e079
Its license:
http://www.kernel.org/pub/linux/kernel/people/mcgrof/firmware/ar9170/LICENSE
This is a new firmware, tested with WNDA3100.
Cc: Peter Grabienski <Peter.Grabienski@Atheros.com>
Cc: Stephen Chen <Stephen.Chen@Atheros.com>
Cc: Michael Fortin <Michael.Fortin@Atheros.com>
Cc: Johnny Cheng <Johnny.Cheng@Atheros.com>
Cc: Yuan-Gu Wei <Yuan-Gu.Wei@atheros.com>
Cc: Joerg Albert <jal2@gmx.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It looks like mac80211 can request the driver to start beaconing with
a beacon interval of zero in some cases (at least for mesh point). This
does not sound correct and something may need to be fixed in
mac80211. However, taken into account the unpleasantness of getting
stuck in an infinite busy loop with rtnl_lock held, let's add a quick
workaround in the driver to avoid the worst symptom while someone more
familiar with the mesh implementation can figure out what should be done
with mac80211 as far as beacon interval configuration is concerned.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ieee80211_conf->beacon_int was deprecated and removed in a cleanup
patch, however it was accidentally added back to ath5k in the change
"ath5k: Allow user/driver to set txpower." Remove it once more,
fixing the following warning:
[13091.968902] WARNING: at drivers/net/wireless/ath/ath5k/base.c:2167 warn_slowpath_null+0x15/0x1a()
[13091.968906] Hardware name: MacBook1,1
[13091.968909] Modules linked in: usb_storage fuse i915 drm af_packet acpi_cpufreq binfmt_misc dm_mirror dm_region_hash dm_log dm_multipath dm_mod snd_hda_codec_idt snd_hda_intel snd_hda_codec snd_seq_dummy hid_apple arc4 ecb snd_seq_oss snd_seq_midi_event usbhid snd_seq ath5k mac80211 appletouch snd_seq_device snd_pcm_oss snd_mixer_oss sky2 snd_pcm ath processor cfg80211 snd_timer sg ohci1394 snd uhci_hcd bitrev ieee1394 joydev ehci_hcd crc32 snd_page_alloc button ac thermal battery sr_mod applesmc cdrom evdev input_polldev unix [last unloaded: microcode]
[13091.968985] Pid: 2132, comm: phy0 Tainted: G W 2.6.30-rc5-wl #118
[13091.968988] Call Trace:
[13091.968994] [<c0125884>] warn_slowpath_fmt+0x77/0xa6
[13091.969003] [<c03557d8>] ? _spin_unlock+0x2c/0x41
[13091.969008] [<c0355a56>] ? _spin_lock_irqsave+0x15/0x69
[13091.969012] [<c0355783>] ? _spin_unlock_irqrestore+0x34/0x5d
[13091.969019] [<c01445bb>] ? trace_hardirqs_off+0xb/0xd
[13091.969024] [<c0355783>] ? _spin_unlock_irqrestore+0x34/0x5d
[13091.969029] [<c01445bb>] ? trace_hardirqs_off+0xb/0xd
[13091.969034] [<c0355783>] ? _spin_unlock_irqrestore+0x34/0x5d
[13091.969039] [<c01258c8>] warn_slowpath_null+0x15/0x1a
[13091.969054] [<f965846d>] ath5k_beacon_update_timers+0x44/0x27f [ath5k]
[13091.969059] [<c0126370>] ? vprintk+0x2dd/0x312
[13091.969063] [<c0125e50>] ? release_console_sem+0x1a6/0x1d3
[13091.969076] [<f96586c5>] ath5k_reset_tsf+0x1d/0x2c [ath5k]
[13091.969095] [<f93f4426>] __ieee80211_sta_join_ibss+0x35/0x3aa [mac80211]
[13091.969102] [<c0252793>] ? extract_entropy+0x47/0x8a
[13091.969121] [<f93f4b21>] ieee80211_sta_find_ibss+0x2de/0x32f [mac80211]
[13091.969126] [<c035422c>] ? mutex_lock_nested+0x28b/0x2a5
[13091.969145] [<f93f4b8e>] ? ieee80211_ibss_notify_scan_completed+0x1c/0x6f [mac80211]
[13091.969164] [<f93f4bc9>] ieee80211_ibss_notify_scan_completed+0x57/0x6f [mac80211]
[13091.969182] [<f93f26da>] ieee80211_scan_completed+0x31a/0x33f [mac80211]
[13091.969201] [<f93f27ca>] ieee80211_scan_work+0xcb/0x18b [mac80211]
[13091.969207] [<c0133a6a>] worker_thread+0x1b1/0x28e
[13091.969212] [<c0133a25>] ? worker_thread+0x16c/0x28e
[13091.969230] [<f93f26ff>] ? ieee80211_scan_work+0x0/0x18b [mac80211]
[13091.969237] [<c013736e>] ? autoremove_wake_function+0x0/0x38
[13091.969242] [<c01338b9>] ? worker_thread+0x0/0x28e
[13091.969246] [<c0137031>] kthread+0x4a/0x70
[13091.971460] [<c0136fe7>] ? kthread+0x0/0x70
[13091.971467] [<c0103527>] kernel_thread_helper+0x7/0x10
[13091.971470] ---[ end trace 8defaa5d15c50cef ]---
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds the debug file to the ath9k debugfs, which lets you modify
the debug_mask at runtime, without having to reload the ath9k module.
Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch combines the legacy and 11n rcstats into one, using the normal
rate table indices instead of two separate indices for each mode. Legacy
rates also get all of the PER and retry information, now, too.
Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
I have a TrendNet 652-BRP running OpenWRT + ath9k very well. The only
problem is that the beacon gets stuck maybe once a day. After
Vasanthakumar Thiagarajan's "ath9k: cleanup beacon parameters
configuration" patch, ath9k would nearly re-configure the beacons after it
detected the stuck beacon, and did a reset. But it would fail the
SC_OP_TSF_RESET check in ath_beacon_config_ap. This patch gets the beacon
fully reconfigured after the reset.
Signed-off-by: Jeff Hansen <x@jeffhansen.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
