summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath
AgeCommit message (Collapse)Author
2011-01-04ath9k : few rate control clean upsMohammed Shafi Shajakhan
Remove some obvious looking dead code and rename few functions Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k: fix beacon restart on channel changeRajkumar Manoharan
Restart the beacon timers only if the beacon was already configured. Otherwise beacons timers are restarted unnecessarily in unassociated state too. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04Revert "ath9k: Parse DTIM period from mac80211"Mohammed Shafi Shajakhan
This reverts commit 0ce3bcfc84900a64347b0fe1140229bd81314008. Event though with the above commit we obtain the configured DTIM period from the AP rather than always hardcoding it to '1', this seems to cause problems under the following scenarios: * Preventing association with broken AP's * Adds latency in roaming So its better to always use the safe value of '1' for dtim period Cc: Jouni Malinen <Jouni.Malinen@Atheros.com> Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_hw: fix dma descriptor rx error bit parsingFelix Fietkau
An Rx DMA descriptor can have multiple error bits set, and some error bits (e.g. MIC failure) are filtered by the driver based on other criteria. Remove the 'else' in various error bit checks so that all error information is properly passed to the driver. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Move LED/RFKILL code to htc_drv_gpio.cSujith Manoharan
And add the copyright/license header. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Fix fast channel changeSujith Manoharan
When returning to the operating channel, a full HW reset has to be done instead of a fast channel change. Since sw_scan_complete() is called after the config() call for the home channel, we end up doing a FCC. Fix this issue by checking the OFFCHANNEL flag to determine FCC. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Handle FATAL eventsSujith Manoharan
The device has to be reset when a FATAL event is received. Not doing so would leave the card in a non-working state. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Move work cancellation outside of mutexSujith Manoharan
There is no need to lock the various work cancellation calls. This will be helpful when handling FATAL events. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Handle pending URBs properlySujith Manoharan
When doing a channel change, the pending URBs have to be killed properly on calling htc_stop(). This fixes the probe response timeout seen when sending UDP traffic at a high rate and running background scan at the same time. Cc: stable <stable@kernel.org> Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k: Few clean ups in beacon config parametersMohammed Shafi Shajakhan
Some minor clean ups in assigning values to beacon config parameters Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04carl9170: fix usb pm suspend->resume woesChristian Lamparter
This patch revamps some common code-paths which are shared between (re-)initialization and suspend/resume subroutines. It also adds some helpful comments about quirks and associated difficulties. It's quite big, but it should fix #25382: <https://bugzilla.kernel.org/show_bug.cgi?id=25382> And hopefully the code is robust enough to deal with all possible suspend/resume scenarios without requiring the user to do any sort of manual and possibly dangerous work. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04carl9170: reduce channel change delayChristian Lamparter
By removing two "safety" msleeps (and an echo nop), the channel change delay is effectively halved. Previously, the delay could be as long as 260 ms and the device could not go off-channel without risking to miss the next DTIM beacon [interval ~307 ms]. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04carl9170: add missing return-value checkChristian Lamparter
This patch adds a forgotten bail-out path. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath5k: fix cycle counter inconsistent lockingBob Copeland
ath5k_reset is called from process context and takes the cc_lock with plain spin_lock(), but cc_lock can also be taken from tasklets in softirq context. Thus we need to at least use spin_lock_bh. This fixes the following lockdep warning: [ 19.967874] sky2 0000:01:00.0: eth0: enabling interface [ 19.982761] ieee80211 phy0: device now idle [ 20.904809] NET: Registered protocol family 17 [ 21.243857] ieee80211 phy0: device no longer idle - scanning [ 21.404343] [ 21.404346] ================================= [ 21.404450] [ INFO: inconsistent lock state ] [ 21.404518] 2.6.37-rc7-wl+ #242 [ 21.404582] --------------------------------- [ 21.404650] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. [ 21.404721] kworker/u:4/982 [HC0[0]:SC1[3]:HE1:SE0] takes: [ 21.404792] (&(&common->cc_lock)->rlock){+.?...}, at: [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] {SOFTIRQ-ON-W} state was registered at: [ 21.405011] [<c105cadd>] __lock_acquire+0x62f/0x13c1 [ 21.405011] [<c105d944>] lock_acquire+0xd5/0xf1 [ 21.405011] [<c12c978d>] _raw_spin_lock+0x45/0x72 [ 21.405011] [<f8111533>] ath5k_reset+0x2c0/0x349 [ath5k] [ 21.405011] [<f8111a7a>] ath5k_start+0xb8/0x139 [ath5k] [ 21.405011] [<f849c714>] ieee80211_do_open+0x13f/0x819 [mac80211] [ 21.405011] [<f849ce51>] ieee80211_open+0x63/0x66 [mac80211] [ 21.405011] [<c1258b2e>] __dev_open+0x8d/0xb6 [ 21.405011] [<c1255c64>] __dev_change_flags+0x9d/0x114 [ 21.405011] [<c1258a75>] dev_change_flags+0x18/0x44 [ 21.405011] [<c1262990>] do_setlink+0x23f/0x521 [ 21.405011] [<c1262d58>] rtnl_setlink+0xe6/0xea [ 21.405011] [<c126347c>] rtnetlink_rcv_msg+0x18a/0x1a0 [ 21.405011] [<c126d5f0>] netlink_rcv_skb+0x35/0x7b [ 21.405011] [<c12632eb>] rtnetlink_rcv+0x20/0x27 [ 21.405011] [<c126d370>] netlink_unicast+0x1bb/0x21e [ 21.405011] [<c126db21>] netlink_sendmsg+0x23b/0x288 [ 21.405011] [<c124823c>] sock_sendmsg+0xac/0xc4 [ 21.405011] [<c1248680>] sys_sendmsg+0x152/0x1a2 [ 21.405011] [<c1249b0d>] sys_socketcall+0x214/0x275 [ 21.405011] [<c10029d0>] sysenter_do_call+0x12/0x36 [ 21.405011] irq event stamp: 138032 [ 21.405011] hardirqs last enabled at (138032): [<c12ca252>] _raw_spin_unlock_irqrestore+0x3b/0x5e [ 21.405011] hardirqs last disabled at (138031): [<c12c98cc>] _raw_spin_lock_irqsave+0x18/0x7e [ 21.405011] softirqs last enabled at (138024): [<f84a570e>] ieee80211_tx_skb+0x47/0x49 [mac80211] [ 21.405011] softirqs last disabled at (138027): [<c100452b>] do_softirq+0x63/0xb4 [ 21.405011] [ 21.405011] other info that might help us debug this: [ 21.405011] 3 locks held by kworker/u:4/982: [ 21.405011] #0: (name){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b [ 21.405011] #1: ((&(&local->scan_work)->work)){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b [ 21.405011] #2: (&local->mtx){+.+.+.}, at: [<f84920fb>] ieee80211_scan_work+0x32/0x4a4 [mac80211] [ 21.405011] [ 21.405011] stack backtrace: [ 21.405011] Pid: 982, comm: kworker/u:4 Not tainted 2.6.37-rc7-wl+ #242 [ 21.405011] Call Trace: [ 21.405011] [<c12c6e68>] ? printk+0x1d/0x25 [ 21.405011] [<c105a742>] print_usage_bug+0x181/0x18b [ 21.405011] [<c105b196>] ? check_usage_forwards+0x0/0xb6 [ 21.405011] [<c105a9ec>] mark_lock+0x2a0/0x4aa [ 21.405011] [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd [ 21.405011] [<c105ca68>] __lock_acquire+0x5ba/0x13c1 [ 21.405011] [<c1059eed>] ? trace_hardirqs_off_caller+0x18/0x8d [ 21.405011] [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd [ 21.405011] [<c1050411>] ? local_clock+0x2c/0x4f [ 21.405011] [<c1059e00>] ? save_trace+0x2/0xa0 [ 21.405011] [<c105ac39>] ? mark_held_locks+0x43/0x5b [ 21.405011] [<c12ca252>] ? _raw_spin_unlock_irqrestore+0x3b/0x5e [ 21.405011] [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<c105d944>] lock_acquire+0xd5/0xf1 [ 21.405011] [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<c12c9b1a>] _raw_spin_lock_bh+0x4a/0x77 [ 21.405011] [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<c105ac39>] ? mark_held_locks+0x43/0x5b [ 21.405011] [<f8113496>] ath5k_tasklet_ani+0x1d/0x27 [ath5k] [ 21.405011] [<c1037304>] tasklet_action+0x96/0x137 [ 21.405011] [<c10379b5>] __do_softirq+0xde/0x1c3 [ 21.405011] [<c10b0cef>] ? arch_get_unmapped_area_topdown+0x3b/0x127 [ 21.405011] [<c10378d7>] ? __do_softirq+0x0/0x1c3 [ 21.405011] <IRQ> [<c1036dee>] ? irq_exit+0x3d/0x49 [ 21.405011] [<c1003b4f>] ? do_IRQ+0x98/0xac [ 21.405011] [<c1002eee>] ? common_interrupt+0x2e/0x34 [ 21.405011] [<c103007b>] ? sys_unshare+0x57/0x226 [ 21.405011] [<c1047fee>] ? queue_delayed_work+0x1/0x27 [ 21.405011] [<f84a83a0>] ? ieee80211_queue_delayed_work+0x2e/0x33 [mac80211] [ 21.405011] [<f8492528>] ? ieee80211_scan_work+0x45f/0x4a4 [mac80211] [ 21.405011] [<c104620e>] ? process_one_work+0x26e/0x41b [ 21.405011] [<c1046158>] ? process_one_work+0x1b8/0x41b [ 21.405011] [<f84920c9>] ? ieee80211_scan_work+0x0/0x4a4 [mac80211] [ 21.405011] [<c10466b6>] ? worker_thread+0x18a/0x2a5 [ 21.405011] [<c12ca25e>] ? _raw_spin_unlock_irqrestore+0x47/0x5e [ 21.405011] [<c104652c>] ? worker_thread+0x0/0x2a5 [ 21.405011] [<c104abe7>] ? kthread+0x67/0x6c [ 21.405011] [<c104ab80>] ? kthread+0x0/0x6c [ 21.405011] [<c1002efa>] ? kernel_thread_helper+0x6/0x10 Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k: fix spur mitigation no-spur case for AR9002Brian Prodoehl
For the AR9002, the spur frequency read from the EEPROM is mangled before being compared against AR_NO_SPUR. This results in the driver trying to set up the spur mitigation for bogus spurs, rather than cleanly breaking out. Signed-off-by: Brian Prodoehl <bprodoehl@nomadio.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k: spin_lock_bh is not required within tasklet context.Senthil Balasubramanian
Disabling BH is not required while running from a tasklet context and so replace spin_lock_bh with just spin_lock. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath5k: Move mac80211 functions into new fileBruno Randolf
Move mac80211 functions into new file mac80211-ops.c to have a better separation and to make base.c smaller. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath9k: Reset keycache on resumeMohammed Shafi Shajakhan
It looks like some hardware registers are left into undefined state after suspend/resume. At minimum, this can cause odd issues related to key cache and hardware trying to encrypt/decrypt frames unexpectedly. This seems to happen even when there is no keys configured, i.e., hardware can end up touching TX frames just based of invalid key cache context even if the driver is not asking a specific entry to be used. In addition, RX can likely be affected. This patch fixes this issue. Signed-off-by: Jouni Malinen <Jouni.Malinen@Atheros.com> Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath9k_hw: Fix bug in eeprom data length validation for AR9485Vasanthakumar Thiagarajan
The size of the eeprom data is 1088 bytes for AR9485. But a sanity check is done against 4K which would result in a 'potential read past the end of the buffer' smatch complaint. Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath5k: Use helper function to get eeprom mode from channelBruno Randolf
Introduce a helper function to get the EEPROM mode from channel and remove multiple similar switch statements. Also since it's now easy to get the EEPROM mode from the channel, use them inside the functions which need it, instead of passing a redundant ee_mode parameter. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath5k: Remove ATH5K_INI_RFGAIN defines, use band insteadBruno Randolf
Remove redundant defines. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath5k: Track current TX power separately from max TX powerBruno Randolf
Add a new variable to keep track of the currently configured tx power. Before max_pwr was re-used for keeping the maximum allowed power as well as the current configuration. Doing a min() on it allows you to lower the txpower, but how would you be able to make it higher again? This patch fixes that by adding a new variable ah_cur_pwr which is used instead of txp_max_pwr to keep the current configuration. txp_max_pwr is used to check if we are within the limits. Another problem fixed by this patch is that it avoids setting a zero txpower when things are initialized first and the current power is not yet set. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath5k: Separate powertable setup and writingBruno Randolf
And rename functions which write the powertable to make it clearer. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath5k: Simplify powertable recalculationBruno Randolf
Let ath5k_hw_txpower() decide if it can re-use the powertable or if it has to be recalculated instead of passing a 'fast' flag from the outside. Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath9k: unlock on error path in ath9k_change_interface()Dan Carpenter
There is a missing unlock when we hit the "No beacon slot available" error condition. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath9k: Use pci_is_pcie()Hauke Mehrtens
Use function pci_is_pcie() instead of accessing struct member directly. CC: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath5k: Use pci_is_pcie()Hauke Mehrtens
Use function pci_is_pcie() instead of accessing struct member directly. CC: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath9k: fix aphy / wiphy idle mismatchLuis R. Rodriguez
ath9k supports its own set of virtual wiphys, and it uses the mac80211 idle notifications to know when a device needs to be idle or not. We recently changed ath9k to force idle on driver stop() and on resume but forgot to take into account ath9k's own virtual wiphy idle states. These are used internally by ath9k to check if the device's radio should be powered down on each idle call. Without this change its possible that the device could have been forced off but the virtual wiphy idle was left on. Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath9k: Fix warnings on card removalRajkumar Manoharan
The recently added warning message on power change failure is not needed on device removal. ath: Failed to wakeup in 500us ------------[ cut here ]------------ WARNING: at drivers/net/wireless/ath/ath9k/hw.c:1618 ath9k_hw_setpower+0x61f/0x630 [ath9k_hw]() Hardware name: 64756D6 Pid: 540, comm: kworker/u:3 Not tainted 2.6.37-rc6-wl #37 Call Trace: [<ffffffff810501aa>] warn_slowpath_common+0x7a/0xb0 [<ffffffffa056e280>] ? ath9k_iowrite32+0x0/0x90 [ath9k] [<ffffffff810501f5>] warn_slowpath_null+0x15/0x20 [<ffffffffa05226ef>] ath9k_hw_setpower+0x61f/0x630 [ath9k_hw] [<ffffffffa05700e5>] ath9k_ps_wakeup+0x85/0xd0 [ath9k] [<ffffffffa0570685>] ath9k_configure_filter+0x25/0x80 [ath9k] [<ffffffffa04dde43>] ieee80211_configure_filter+0x133/0x190 [mac80211] [<ffffffffa04ee502>] ieee80211_do_stop+0x132/0x540 [mac80211] [<ffffffff813466ff>] ? _raw_spin_unlock_bh+0x1f/0x30 [<ffffffff812b6923>] ? dev_deactivate+0x1c3/0x1e0 [<ffffffffa04ee925>] ieee80211_stop+0x15/0x20 [mac80211] [<ffffffff8129d1b6>] __dev_close+0x56/0x90 Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22ath9k_htc: Fix warning on device removalSujith Manoharan
The commit "ath9k_hw: warn if we cannot change the power to the chip" introduced a new warning to indicate chip powerup failures, but this is not required for devices that have been removed. Handle USB device removal properly by checking for unplugged status. For PCI devices, this warning will still be seen when the card is pulled out, not sure how to check for card removal. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-22Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem Conflicts: drivers/net/wireless/iwlwifi/iwl-1000.c drivers/net/wireless/iwlwifi/iwl-6000.c drivers/net/wireless/iwlwifi/iwl-core.h
2010-12-22Merge branch 'master' into for-nextJiri Kosina
Conflicts: MAINTAINERS arch/arm/mach-omap2/pm24xx.c drivers/scsi/bfa/bfa_fcpim.c Needed to update to apply fixes for which the old branch was too outdated.
2010-12-20ath9k: do not limit the chainmask to 1 for legacy modeFelix Fietkau
Restricting the chainmask to 1 for legacy mode disables useful features such as MRC, and it reduces the available transmit power. I can't think of a good reason to do this in legacy mode, so let's just get rid of that code. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20ath9k_hw: fix PA predistortion HT40 maskFelix Fietkau
The commit 'ath9k_hw: Disable PAPRD for rates with low Tx power' changed the code that sets the PAPRD rate masks to use only either the HT20 mask or the HT40 mask. This is wrong, as the hardware can still use HT20 rates even when configured for HT40, and the operating channel mode does not affect PAPRD operation. The register for the HT40 rate mask is applied as a mask on top of the other registers to selectively disable PAPRD for specific rates on HT40 packets only. This patch changes the code back to the old behavior which matches the intended use of these registers. While with current cards this should not make any practical difference (according to Atheros, the HT20 and HT40 mask should always be equal), it is more correct that way, and maybe the HT40 mask will be used for some rare corner cases in the future. Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20ath9k: Properly initialize channel table for 2GHzMohammed Shafi Shajakhan
ath9k channel table for 2Ghz does not seems to initialize the 'band' parameter.Though it does not seems to cause any visible issue it looks odd when we initialize the 'band' parameter for 5Ghz channel table while not so for 2Ghz. Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20ath9k_hw: remove baseband rfsilent supportFelix Fietkau
When rfkill is enabled, ath9k_hw unnecessarily configured the baseband to turn off based on GPIO input, however that code was hardcoded to GPIO 0 instead of ah->rfkill_gpio. Since ath9k uses software rfkill anyway, this code is completely unnecessary and should be removed in case anything else ever uses GPIO 0. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20ath9k: fix queue depth check for forming new aggregatesFelix Fietkau
To improve aggregation length, there should not be more than two fully formed A-MPDU frames in the hardware queue. To ensure this, the code checks the tx queue length before forming new A-MPDUs. This can reduce the throughput (or maybe even starve out A-MPDU traffic) when too many non-aggregated frames are in the queue. Fix this by keeping track of pending A-MPDU frames (even when they're sent out as single frames), but exclude rate control probing frames to improve performance. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20ath5k: Set available antenna information for cfg80211Bruno Randolf
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16ath5k: Fix surveyBruno Randolf
The old survey implementation was broken and returned nonsense data. Clear cycle counters and survey data on reset. Since the cycle counters easily overflow it's better to keep a local version of collected survey data (in ms resolution, instead of clockrate) and update this every time survey is retrieved. If survey is retrieved often enough to avoid cycle counter overflows this works fine, otherwise we could update survey more often, like ath9k does. Still only the survey for the current channel is kept. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16ath: fix NULL pointer dereference on reg_notifier()Luis R. Rodriguez
The reg_notifier() was recently updated as being capable of having the request passed as NULL, fix ath to follow this API change. Without this we end up oopsing: BUG: unable to handle kernel NULL pointer dereference at 0000000000000004 IP: [<ffffffffa02fb8cb>] ath_reg_notifier_apply+0x5b/0xa0 [ath] PGD b4c4c067 PUD b4c4d067 PMD 0 Oops: 0000 [#1] SMP DEBUG_PAGEALLOC last sysfs file: /sys/devices/pci0000:00/0000:00:1b.0/uevent CPU 1 Modules linked in: <etc> Pid: 436, comm: modprobe Not tainted 2.6.37-rc5-wl+ #36 6460DWU/6460DWU RIP: 0010:[<ffffffffa02fb8cb>] [<ffffffffa02fb8cb>] ath_reg_notifier_apply+0x5b/0xa0 [ath] RSP: 0018:ffff8800b6f6baa8 EFLAGS: 00010246 RAX: ffff8800b527b254 RBX: ffff8800b532c180 RCX: 0000000000000018 RDX: ffff8800b530c108 RSI: 0000000000000000 RDI: ffff8800b532c180 RBP: ffff8800b6f6baa8 R08: ffff8800b532f268 R09: 0000000000000235 R10: 00000000000016ad R11: 0000000000000018 R12: 0000000000000000 R13: 0000000000000016 R14: ffff8800b532f268 R15: 0000000000000011 FS: 00007f0c53104700(0000) GS:ffff8800bed00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000004 CR3: 00000000b6531000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process modprobe (pid: 436, threadinfo ffff8800b6f6a000, task ffff8800b404dc40) Stack: ffff8800b6f6bac8 ffffffffa03ea651 ffff8800b532c180 ffff8800b527b254 ffff8800b6f6bb38 ffffffffa01835ca ffffffffa019ed00 00000000a019ed80 0000000000000002 ffff880000000002 ffffffffa0366140 0000000010aee572 Call Trace: [<ffffffffa03ea651>] ath9k_reg_notifier+0x41/0x50 [ath9k] [<ffffffffa01835ca>] wiphy_update_regulatory+0x4ba/0x5a0 [cfg80211] [<ffffffffa0366140>] ? ieee80211_register_hw+0xa0/0x5b0 [mac80211] [<ffffffffa0366140>] ? ieee80211_register_hw+0xa0/0x5b0 [mac80211] [<ffffffffa017f994>] wiphy_register+0x1d4/0x360 [cfg80211] [<ffffffff8114b918>] ? __kmalloc+0x108/0x1c0 [<ffffffffa0366223>] ieee80211_register_hw+0x183/0x5b0 [mac80211] [<ffffffffa03eb49b>] ath9k_init_device+0x66b/0x850 [ath9k] [<ffffffffa03f9dd6>] ath_pci_probe+0x2f6/0x3c0 [ath9k] [<ffffffff81037529>] ? default_spin_lock_flags+0x9/0x10 [<ffffffff812e19cf>] local_pci_probe+0x5f/0xd0 [<ffffffff812e2bf1>] pci_device_probe+0x101/0x120 [<ffffffff81390aca>] ? driver_sysfs_add+0x7a/0xb0 [<ffffffff81390c26>] driver_probe_device+0x96/0x1c0 [<ffffffff81390deb>] __driver_attach+0x9b/0xa0 [<ffffffff81390d50>] ? __driver_attach+0x0/0xa0 [<ffffffff81390008>] bus_for_each_dev+0x68/0x90 [<ffffffff81390a4e>] driver_attach+0x1e/0x20 [<ffffffff81390309>] bus_add_driver+0xe9/0x290 [<ffffffffa0407000>] ? ath9k_init+0x0/0x4d [ath9k] [<ffffffff81391130>] driver_register+0x80/0x150 [<ffffffffa0407000>] ? ath9k_init+0x0/0x4d [ath9k] [<ffffffffa0407000>] ? ath9k_init+0x0/0x4d [ath9k] [<ffffffff812e2e76>] __pci_register_driver+0x56/0xd0 [<ffffffffa03f9ec3>] ath_pci_init+0x23/0x30 [ath9k] [<ffffffffa040702b>] ath9k_init+0x2b/0x4d [ath9k] [<ffffffff81002053>] do_one_initcall+0x43/0x190 [<ffffffff8109fb5b>] sys_init_module+0xbb/0x200 [<ffffffff8100c042>] system_call_fastpath+0x16/0x1b Code: <who even reads this anyway? haha, ok you do> RIP [<ffffffffa02fb8cb>] ath_reg_notifier_apply+0x5b/0xa0 [ath] RSP <ffff8800b6f6baa8> CR2: 0000000000000004 ---[ end trace 6d03d3c7eda9f06b ]--- Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16ath9k_hw: Configure appropriate Tx power when PAPRD failsVasanthakumar Thiagarajan
Target Tx power available in eeprom is for PAPRD. If PAPRD fails, paprd scale factor needs to be detected from this target tx power. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16ath9k_hw: Disable PAPRD for rates with low Tx powerVasanthakumar Thiagarajan
When the drop in Tx power for a particular mcs rate exceeds the paprd scale factor, paprd may not work properly. Disable paprd for any such rates. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16ath9k_hw: Add a helper to get paprd scale factorVasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16ath9k_hw: Tx IQ cal changes for AR9003Vasanthakumar Thiagarajan
Add multiple Tx IQ cal support to improve EVM accross different power levels. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16ath9k_hw: Move get_streams() to hw.hVasanthakumar Thiagarajan
This helper can be used in multiple places. Also make it inline returning u8. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16ath9k_hw: Remove unnecessary Rx IQ cal register configuration in ↵Vasanthakumar Thiagarajan
ar9003_hw_tx_iq_cal() Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16ath9k_hw: Remove delay during regwrite of analog shift registersVasanthakumar Thiagarajan
This is not needed for AR9003. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-15ath9k: Add comments for making pm-qos as modparamMohammed Shafi Shajakhan
PM-QOS value can be user specified via module parameter. This patch adds few comments regarding this in the driver code. Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-15ath9k_htc: Remove PCI specific configurationSujith Manoharan
This is not required for USB devices. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-15mac80211: Add timeout to BA session start APISujith Manoharan
Allow drivers or rate control algorithms to specify BlockAck session timeout when initiating an ADDBA transaction. This is useful in cases where maintaining persistent BA sessions does not incur any overhead. The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc drivers. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-06-26 19:40:19 +0000