summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath
AgeCommit message (Collapse)Author
2010-12-07ath9k_hw: Define IQcal correction coefficient registers using indexVasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Program appropriate chianmask for AR9485 before starting AGC/IQ calVasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Configure power control only for the supported chainsVasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Read and configure turnning caps to regulate freq accuracyVasanthakumar Thiagarajan
Right now it is done for only AR9485, will be done for ar9003 also after proper testing. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Configure internal regulator for AR9485Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Read and configure antenna diversity control for AR9485Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Configure xpa bias level for AR9485Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k: Read spur channel information from eeprom for AR9485Vasanthakumar Thiagarajan
Also spur channel count and range is different for AR9485. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Add a helper function to get spur channel pointer from cal data ↵Vasanthakumar Thiagarajan
for AR9003 family This helper function would be used for AR9485. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 for AR9485Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k: Configure pll control for AR9485Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Find the maximum number of chains that hw supportsVasanthakumar Thiagarajan
Have it in ah->caps. This will be used during various calibrations. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k: Enable extended synch for AR9485 to fix L0s recovery issueVasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k: Disable TX STBC for AR9485Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Disable LDPC for AR9485Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Eeeprom changes for AR9485Vasanthakumar Thiagarajan
Calibration data are stored at 4k address (0xfff). The cal data for AR9485 is not compressed so its lengh can exceed 1024 limit, take care of that. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Initialize tx/rx gain table from initvals.h for AR9485Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Initialize mode registers for AR9485Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Enable hw initialization for AR9485Vasanthakumar Thiagarajan
Also make it a supported mac Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Add initvals.h for AR9485Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k_hw: Define hw version macros for AR9485Vasanthakumar Thiagarajan
AR9485 is a single chain and single band (2.4 Ghz) chip. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath5k: remove MODULE_VERSIONJohn W. Linville
Since this is updated manually and sporadically, it is fairly useless anyway. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath: Fix ath_dbg access beyond array boundJoe Perches
ar9300RateSize is not necessarily a power of 4. Change ar9003_hw_set_target_power_eeprom to print the targetPowerValT2 array one per line. ath9k_hw_ar9300_set_txpower repeated the output 4 times per line, change it to print the targetPowerValT2 value one per line. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath: Convert ath_print to ath_dbgJoe Perches
Remove ath/debug.h and the includes of these files. Coalesce long formats. Correct a few misspellings and missing "\n"s from these logging messages. Remove unnecessary trailing space before a newline. Remove ARRAY_SIZE casts, use printf type %zu Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath: Convert ath_print(.., ATH_DBG_FATAL to ath_errJoe Perches
So these errors are always emitted at KERN_ERR level. Remove ARRAY_SIZE casts, use printf type %zu Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath: Add and use ath_printk and ath_<level>Joe Perches
Add ath_printk and ath_<level> similar to dev_printk and dev_<level> from device.h This allows a more gradual rename of ath_print to to ath_dbg or perhaps ath_debug. This basically removes debug.h leaving only an #define ath_printk ath_dbg there and moving all the ATH_DBG_<foo> enums to ath.h I do not think there's much purpose for struct ath_common * being passed to the ath_printk functions, but perhaps there might be. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k: fix beacon resource related race conditionRajkumar Manoharan
The beacon tasklet is accesssing the bslot info for beacon generation. Meanwhile the same slot can be freed on interface deletion. Current the remove_interface disables the beacon alert after freeing the slot. This may leads to null pointer access. This patch disables SWBA and kills the beacon tasklet to prevent access to the slot to be freed. After releasing the slot, swba will be enabled again upon the availablity of beaconing interfaces. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k: Fix STA disconnect issue due to received MIC failed bcast framesSenthil Balasubramanian
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying this status for MIC failed frames is buggy. Due to this, MIC failure events for broadcast frames are not sent to supplicant resulted in AP disconnecting the STA. Able to pass Wifi Test case 5.2.18 with this fix. Cc: Stable <stable@kernel.org> (2.6.36+) Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k: fix a DMA related race condition on resetFelix Fietkau
When ath_drain_all_txq fails to stop DMA, it issues a hw reset. This reset happens at a very problematic point in time, when the hardware rx path has not been stopped yet. This could lead to memory corruption, hardware hangs or other issues. To fix these issues, simply remove the reset entirely and check the tx DMA stop status to prevent problems with fast channel changes. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-07ath9k: fix bug in tx powerMatteo Croce
The ath9k driver subtracts 3 dBm to the txpower as with two radios the signal power is doubled. The resulting value is assigned in an u16 which overflows and makes the card work at full power. Cc: stable@kernel.org Signed-off-by: Matteo Croce <matteo@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06ath5k: Include tx ack reporting on hw flagsNick Kossifidis
* Since we report tx acks to the protocol stack, add the needed flag to hw_flags. This way we'll also use the new AP probing mechanism. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06ath5k: Fix reporting of RX dma stop failureNick Kossifidis
* Correctly report failure to stop RX DMA Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06ath5k: Disable ANI during resetNick Kossifidis
* Stop ANI durring reset to prevent false PHY error reports Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06ath5k: Always free tx buffers before resetNick Kossifidis
* Always free tx buffers before reset, since we also empty hw queues. If we don't and a queue gets stuck, we'll never decrease txq_len and sw will keep thinking the queue is still stuck even after reset. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06ath5k: Always write tx powertable on hwNick Kossifidis
* By skipping tx power table calibration we also skip setting tx power table on hw. Make sure we always write tx power table on hw since it gets cleared on reset. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-06ath5k: Use EWMA factor of 1024 instead of 1000Bruno Randolf
This prepares the only place which uses the EWMA library so far for the performance improved implementation coming up, which requires factor and weight to be a power of two. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 Conflicts: drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
2010-12-02ath5k: Fix reset and interrupts for AHB type of devices.Felix Fietkau
On WiSoc we cannot access mac register before it is resetted. It will crash hardware otherwise. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02ath5k: Add AHB bus support.Felix Fietkau
AHB specific functions are now in ahb.c file. AHB bus is compiled in when CONFIG_ATHEROS_AR231X is set in kernel. All other platforms will use PCI bus. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02ath5k: Add initial registers values for radio RF2317 chip.Felix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02ath5k: Add a function to read chipset's MAC revisionFelix Fietkau
Add bus dependent revision read function which is used to determine chipset's MAC before hardware is initialized. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02ath5k: Check if pci pdev struct is initialized in common functions.Felix Fietkau
To be able to support other busses than PCI check if pci device structure is initialized. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02ath5k: Use generic eeprom read from common ath_bus_opts struct.Felix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02ath5k: Move PCI bus functions to separate file.Felix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02ath5k: Introduce ath5k_init_softc function as in ath9kFelix Fietkau
Split pci initialization into hardware specific functions and softc structure initialization. Make function naming similar to ones ath9k. Introduce ath_bus_opts in ath5k for later AHB bus integration. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02ath5k: Use Generic DMA for later support of AHB bus.Felix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02ath9k_htc: Remove unused structuresSujith Manoharan
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02wireless: Remove unnecessary casts of usb_get_intfdataJoe Perches
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02ath9k: hif_usb: Reduce indent 1 columnJoe Perches
Invert test and return early. Move variable declarations to local scope. Don't initialize variables to 0 unnecessarily. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-02ath9k: Move debugfs under ieee80211/[phyname]/ath9k/Ben Greear
This fixes debugfs problems when a phy is renamed, and is able to remove a bit of code that is no longer needed. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-06-27 11:43:04 +0000