| Age | Commit message (Collapse) | Author |
|---|
|
In 63b77bf489881747c5118476918cc8c29378ee63
iwlwifi: dvm: don't send zeroed LQ cmd
I tried to avoid to send zeroed LQ cmd, but I made a (very)
stupid mistake in the memcmp.
Since this patch has been ported to stable, the fix should
go to stable too.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341
Cc: stable@vger.kernel.org
Reported-by: Hinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Move the counter for non-AMPDU frames to mvm. It is needed
for the drain flow which happens once the ieee80211_sta has
been freed, so keeping it in iwl_mvm_sta which is embed into
ieee80211_sta is not a good idea.
Also, since its purpose it to remove the STA in the fw only
after all the frames for this station have exited the shared
Tx queues, we need to decrement it in the reclaim flow. This
flow can happen after ieee80211_sta has been removed, which
means that we have no iwl_mvm_sta there. So we can't know
what is the vif type. Hence, we know audit these frames for
all the vif types.
In order to avoid spawning sta_drained_wk all the time, we
now check that we are in a flow in which draining might
happen - only when mvmsta is NULL. This is better than
previous code that would spawn sta_drained_wk all the time
in AP mode.
Cc: stable@vger.kernel.org [3.9]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the normal flow first MAC_CONTEXT_CMD for particular interface is
never sent while associated. The exception is fw restart flow when
resuming from suspend when WoWLAN is enabled. In this case successive
"add" and "modify" MAC_CONTEXT_CMD commands may be sent with assoc flag
set what cause FW mal functioning. To prevent this never set assoc flag
in MAC_CONTEXT_CMD with action "add".
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Without this command, the firmware will filter out all the
multicast frames. Let them all in as for now. Later we will
want to optimize this to save power.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The FW AUX framework does not handle well cases where time events
fail to be scheduled (and as a result issues assert 0x3330). Until
a proper fix is in place, WA this by always setting the scan type to
SCAN_TYPE_FORCED.
Cc: stable@vger.kernel.org
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
|
|
Add another ID for a 7000 series device.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the stations are being restored because of unassoc
RXON, the LQ cmd may not have been initialized because it
is initialized only after association.
Sending zeroed LQ_CMD makes the fw unhappy: it raises
SYSASSERT_2078.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
[move zero_lq and make static const]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make code simpler a bit.
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make power management in MVM driver enabled by default and
remove using the power_save module parameter. Rely only on
the power_scheme parameter to decide if power management
should be used.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We can check buf against NULL instead of having additional bool
variable.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If on iwl_dump_nic_event_log() error occurs before that function
initialize buf, we process uninitiated pointer in
iwl_dbgfs_log_event_read() and can hit "BUG at mm/slub.c:3409"
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=951241
Cc: stable@vger.kernel.org
Reported-by: ian.odette@eprize.com
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Recently in low power (LP) mode FW moved from active to power save mode
after TX/RX completion faster than in balanced power mode (BPS).
Change AM-to-PSM transition time so that it will be the same as for BPS.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
first_antenna is supposed to return the first antenna as a
0-based bitmap: ANT_A is BIT(0), ANT_B is BIT(1), etc...
Since ffs is 1 based (ffs(BIT(0)) = 1), then we had an
off-by-one bug:
BIT(ffs(ANT_A)) = BIT(ffs(BIT(0))) = BIT(1) = ANT_B.
So what we really want is:
BIT(ffs(ANT_A) - 1) = BIT(ffs(BIT(0)) - 1) = BIT(0) = ANT_A.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Chain noise is done in the firmware and Bluetooth Coexistence
is implemented now.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
drivers/net/wireless/ath/carl9170/debug.c
drivers/net/wireless/ath/carl9170/main.c
net/mac80211/ieee80211_i.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/rt2x00/rt2x00pci.c
net/mac80211/sta_info.c
net/wireless/core.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/rt2x00/rt2x00pci.c
|
|
Until now we didn't handle properly the FLUSH ampdu action
coming from mac80211. This could result in SCD queue leak:
mac80211 would STOP_FLUSH an AMPDU Tx session and remove
the station. If we had still packets on the ring, we
wouldn't deallocate the SCD queue and wait for it to be
empty.
The indication of the queue being empty comes from the Tx
response flow which relies on the tid_data structure. The
problem is that this structure has been cleared when the
station has been removed.
In order to solve this issue, block in the STOP_FLUSH
ampdu_action until the SCD queue is flushed, and only then,
let mac80211 move forward to remove the station.
iwlagn_txfifo_flush had to be enhanced to allow this.
The bug fixed here caused the "txq_id mismatch: 12 0" print.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In commit 332235427a566d8be04b9676a7ac380c8853aa9b
"iwlwifi: mvm: take the valid_{rx,tx}_ant from the TLV"
I replaced the access to nvm_data->valid_tx_ant to an inline
cheking the TLV flags but forgot a few occurences. Fix that.
Change-Id: I92daac735b46738d97fe2dbd5934bb177fd0751b
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-on: https://gerrit.rds.intel.com/12308
Tested-by: IWL Jenkins
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If request_module() failed then we didn't have the correct
opmode module that the driver needs to function, so print
a warning in this case to make it more obvious what could
be wrong. This still won't catch the case where the module
simply doesn't exist because it wasn't compiled though.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It actually handles a BT coex notification, so rename it
to be more self explained.
Also, this function can always look at mvm->last_bt_notif
provided that the latter is updated on time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Using IWL_MVM_STATION_COUNT and IWL_INVALID_STATION together
isn't a good idea as they have different values. Always use
IWL_MVM_STATION_COUNT for an invalid station in MVM and move
the definition of the IWL_INVALID_STATION constant into the
DVM driver to avoid making such mistakes again. The one use
in the transport code can be hard-coded to -1 instead as the
station ID is passed as an integer there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
some new thinkpad laptops use intel chip with new pci id need be added
lspci -vnn output:
Network controller [0280]: Intel Corporation Centrino Advanced-N 6235
[8086:088f] (rev 24)
Subsystem: Intel Corporation Device [8086:5260]
Signed-off-by: Shuduo Sang <sangshuduo@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The iterators don't need to know what bt_kill_msk means.
All they need to know is if reduced Tx power is enabled
on an interface or not. So change the member of the
iterator to be a bool.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The firmware API changed to differentiate between event and
fragment start/end. Change the time-event handling accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Many platforms have issues processing a wakeup signal
while they're still suspending, and will ignore it.
Since our device thinks it woke the platform, and the
platform ignored the signal, it will sleep without
WoWLAN being enabled as the device disables WoWLAN
when having woken the platform.
Resolve this by making the device wait for 10 seconds
after getting the suspend signal before waking up the
platform.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Print the sub-driver (opmode, i.e. DVM or MVM) when the
firmware is loaded.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The function just wraps an existing one, remove it.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The requirement for TX/RX active to powersave transition time for
the Balanced Power Save (BPS) scheme changed. Change the driver
accordingly and set transition time to 100 msec.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Encapsulate the power table command logging in a separate
function to print the same information in both cases.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The firmware starts sending nulldata frames for keepalive immediately
after association, regardless of power management state. The driver
thus needs to configure keep alive period unconditionally.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The driver distinguishes between power management and device's power
down enablement. Power management enablement depends both on driver's
module power parameters and mac80211 decision. The device's power down
depends only on driver's module power parameters. Change the driver to
always send Power Table command to enable or disable both power
management and device's power down.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Active to power save mode transition time for TX/RX in the power
table command is in microseconds, fix the units in the driver.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently power management is supported only when only a single
virtual interface is present. The driver verifies number of created
interfaces and disables power management when multiple interfaces
present. However, this rule does not extend to a P2P device that is
handled differently in the firmware. If a P2P device is added power
management can remain enabled.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Replace SLEEP_OVER_DTIM by SKIP_OVER_DTIM.
Add iwl_mvm prefix to a function name.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Current available FW still doesn't support new PM API.
Therefore, to enable basic power management with the
existing firmware, change the API in the driver back
to the API used in the current firmware.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When we roam to A band, we don't need to constraint WiFi
any more since it is operating on a different band.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows to have better wifi TPT when BT is active under
good RSSI conditions.
Wifi will have better chance to send Acks and Cts even if BT
is active.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Use the per-interface debugfs infrastructure to create a
directory and symlink, and add a file containing debug
data related to each virtual interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
|
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
|
|
Alex Romosan reported that since the mac80211 changes in
"mac80211: start auth/assoc timeout on frame status" and
the subsequent fixes in "mac80211: fix auth/assoc timeout
handling" (commits 1672c0e31917 and 89afe614c0c) there's
sometimes an issue connecting to a 5 GHz network with the
iwlwifi DVM driver.
The reason appears to be that since these commits any bad
TX status makes mac80211 immediately try again, causing
all of the authentication attempts to be quickly rejected
by the firmware as it hasn't heard a beacon yet. Before,
it would wait for the timeout regardless of status.
To fix this, invoke the passive-no-RX workaround when not
associated yet as well. This will cause the first frame
to get lost, but then the driver will stop the queues and
the second attempt will only be transmitted after hearing
a beacon, thus delaying it appropriately to not make the
firmware reject it again.
Reported-by: Alex Romosan <romosan@sycorax.lbl.gov>
Tested-by: Alex Romosan <romosan@sycorax.lbl.gov>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
