| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
For SD8688, FUNC_INIT command is queued before fw_ready flag is
set. This causes the following crash as lbs_thread blocks any
command if fw_ready is not set.
[ 209.338953] [<c0502248>] (__schedule+0x610/0x764) from [<bf20ae24>] (__lbs_cmd+0xb8/0x130 [libertas])
[ 209.348340] [<bf20ae24>] (__lbs_cmd+0xb8/0x130 [libertas]) from [<bf222474>] (if_sdio_finish_power_on+0xec/0x1b0 [libertas_sdio])
[ 209.360136] [<bf222474>] (if_sdio_finish_power_on+0xec/0x1b0 [libertas_sdio]) from [<bf2226c4>] (if_sdio_power_on+0x18c/0x20c [libertas_sdio])
[ 209.373052] [<bf2226c4>] (if_sdio_power_on+0x18c/0x20c [libertas_sdio]) from [<bf222944>] (if_sdio_probe+0x200/0x31c [libertas_sdio])
[ 209.385316] [<bf222944>] (if_sdio_probe+0x200/0x31c [libertas_sdio]) from [<bf01d820>] (sdio_bus_probe+0x94/0xfc [mmc_core])
[ 209.396748] [<bf01d820>] (sdio_bus_probe+0x94/0xfc [mmc_core]) from [<c02e729c>] (driver_probe_device+0x12c/0x348)
[ 209.407214] [<c02e729c>] (driver_probe_device+0x12c/0x348) from [<c02e7530>] (__driver_attach+0x78/0x9c)
[ 209.416798] [<c02e7530>] (__driver_attach+0x78/0x9c) from [<c02e5658>] (bus_for_each_dev+0x50/0x88)
[ 209.425946] [<c02e5658>] (bus_for_each_dev+0x50/0x88) from [<c02e6810>] (bus_add_driver+0x108/0x268)
[ 209.435180] [<c02e6810>] (bus_add_driver+0x108/0x268) from [<c02e782c>] (driver_register+0xa4/0x134)
[ 209.444426] [<c02e782c>] (driver_register+0xa4/0x134) from [<bf22601c>] (if_sdio_init_module+0x1c/0x3c [libertas_sdio])
[ 209.455339] [<bf22601c>] (if_sdio_init_module+0x1c/0x3c [libertas_sdio]) from [<c00085b8>] (do_one_initcall+0x98/0x174)
[ 209.466236] [<c00085b8>] (do_one_initcall+0x98/0x174) from [<c0076504>] (load_module+0x1c5c/0x1f80)
[ 209.475390] [<c0076504>] (load_module+0x1c5c/0x1f80) from [<c007692c>] (sys_init_module+0x104/0x128)
[ 209.484632] [<c007692c>] (sys_init_module+0x104/0x128) from [<c0008c40>] (ret_fast_syscall+0x0/0x38)
Fix it by setting fw_ready flag prior to queuing FUNC_INIT command.
Cc: <stable@vger.kernel.org> # 3.5+
Reported-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/iwlwifi/dvm/tx.c
drivers/net/wireless/ti/wlcore/sdio.c
drivers/net/wireless/ti/wlcore/spi.c
|
|
This prepares for using the spinlock instead of krefs
which is needed in the next patch to track the refs
of combined BSSes correctly.
Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Remove now unused variables.
Remove unnecessary memset after kzalloc->kcalloc.
Whitespace cleanups for these changes.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reg_notifier()'s return value need not be checked
as it is only supposed to do post regulatory work and
that should never fail. Any behaviour to regulatory
that needs to be considered before cfg80211 does work
to a driver should be specified by using the already
existing flags, the reg_notifier() just does post
processing should it find it needs to.
Also make lbs_reg_notifier static.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[move lbs_reg_notifier to not break compile]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Dan Williams <dcbw@redhat.com>
Cc: libertas-dev@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
drivers/net/wireless/mwifiex/sta_ioctl.c
net/mac80211/scan.c
|
|
When a BSS struct is updated, the IEs are currently
overwritten or freed. This can lead to races if some
other CPU is accessing the BSS struct and using the
IEs concurrently.
Fix this by always allocating the IEs in a new struct
that holds the data and length and protecting access
to this new struct with RCU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.
Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This chip is for example used in the GuruPlug.
This patch avoids the following error:
libertas_sdio: failed to load firmware
libertas_sdio: probe of mmc0:0001:1 failed with error -5
The fix is based on code in:
drivers/net/wireless/libertas_uap/uap_sdio_mmc.c
This file can for example be found on the following links:
http://www.xilka.com/sheeva/2.6/2.6.36/2.6.36.2/source/0002-Driver-for-Marvell-Libertas-8688-SDIO-micro-AP-suppo-2.6.35.patch
http://www.downloadsnewit.co.uk/kernel-v3.0.7/
I followed the following wiki to setup a working WiFi client mode
connection on the GuruPlug:
http://wiki.debian.org/libertas
Signed-off-by: Harro Haan <hrhaan@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:
/* Information Element IDs */
enum ieee80211_eid {
:
WLAN_EID_WPA = 221,
WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
:
};
The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.
Cc: Jouni Malinen <j@w1.fi>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> [ipw2x00]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[change libipw as well]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
CMD_MAC_CONTROL is currently sent async to the firmware, and is sent
from the lbs_setup_firmware() path during device init.
This means that device init can complete with commands pending, and
the if_sdio driver will sometimes power down the device (after init)
with this command still pending.
This was causing an occasional spurious command timeout after init,
leading to a device reset.
Fix this by making CMD_MAC_CONTROL synchronous when called from the
lbs_setup_firmware() path.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the interface is down, the hardware is powered off.
However, the suspend handler currently tries to send host sleep commands
(when wakeup params are set) in this configuration, causing a system hang
when going into suspend (the commands will never complete).
Avoid this by detecting this situation and simply returning from
the suspend handler without doing anything special.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pull networking fixes from David Miller:
1) Missed rcu_assign_pointer() in mac80211 scanning, from Johannes
Berg.
2) Allow devices to limit the number of segments that an individual
TCP TSO packet can use at a time, to deal with device and/or driver
specific limitations. From Ben Hutchings.
3) Fix unexpected hard IPSEC expiration after setting the date. From
Fan Du.
4) Memory leak fix in bxn2x driver, from Jesper Juhl.
5) Fix two memory leaks in libertas driver, from Daniel Drake.
6) Fix deref of out-of-range array index in packet scheduler generic
actions layer. From Hiroaki SHIMODA.
7) Fix TX flow control errors in mlx4 driver, from Yevgeny Petrilin.
8) Fix CRIS eth_v10.c driver build, from Randy Dunlap.
9) Fix wrong SKB freeing in LLC protocol layer, from Sorin Dumitru.
10) The IP output path checks neigh lookup errors incorrectly, it needs
to use IS_ERR(). From Vasiliy Kulikov.
11) An estimator leak leads to deref of freed memory in timer handler,
fix from Hiroaki SHIMODA.
12) TCP early demux in ipv6 needs to use DST cookies in order to
validate the RX route properly. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
net: ipv6: fix TCP early demux
net: Use PTR_RET rather than if(IS_ERR(.. [1]
net_sched: act: Delete estimator in error path.
ip: fix error handling in ip_finish_output2()
llc: free the right skb
ixp4xx_eth: fix ptp_ixp46x build failure
drivers/atm/iphase.c: fix error return code
tcp_output: fix sparse warning for tcp_wfree
drivers/net/phy/mdio-mux-gpio.c: drop devm_kfree of devm_kzalloc'd data
batman-adv: select an internet gateway if none was chosen
mISDN: Bugfix for layer2 fixed TEI mode
igb: don't break user visible strings over multiple lines in igb_ethtool.c
igb: correct hardware type (i210/i211) check in igb_loopback_test()
igb: Fix for failure to init on some 82576 devices.
cris: fix eth_v10.c build error
cdc-ncm: tag Ericsson WWAN devices (eg F5521gw) with FLAG_WWAN
isdnloop: fix and simplify isdnloop_init()
hyperv: Move wait completion msg code into rndis_filter_halt_device()
net/mlx4_core: Remove port type restrictions
net/mlx4_en: Fixing TX queue stop/wake flow
...
|
|
The if_sdio_card structure was never being freed, and neither
was the command structure used for association.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On an OLPC XO-1.5 we have seen the following situation:
- the system starts going into suspend
- no wake params are set, so the mmc layer removes the card
- during remove, we send a command to the card
- that command fails, causing if_sdio's reset method to try and remove
the mmc card in attempt to reset it
- the mmc layer is not happy about being asked to remove a card that
it is already removing, and the kernel crashes
While the MMC layer could possibly be taught to behave better here,
it also seems sensible for libertas not to try and reset a card if
we're in the process of removing it anyway.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Switch over to using olpc-ec.h in multiple steps, so as not to break builds.
This covers every driver that calls olpc_ec_cmd().
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Paul Fox <pgf@laptop.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
Signed-off-by: Duan Jiong <djduanjiong@gmail.com>
|
|
We found a deadlock in the handling of command failures/reset conditions.
For example:
1. Two commands are in the queue.
2. The first command is sent, but causes a timeout, which kicks off an
asynchronous device reset
3. The second command is queued (but not yet sent to the hardware)
4. The device reset kicks in, causing the if_usb disconnect handler to
set the "surprise removed" flag to be set as the device disappears
from the bus. This causes lbs_thread to stop processing things
("adapter removed; waiting to die"), not processing any further
commands, leaving the second queued command "in the air", causing a
deadlock.
Fix this by removing the surpriseremoved flag setting in if_usb. I can't
see any reason why this needs to be done so early. lbs_remove_card will set
this flag at an appropriate time - i.e. after all pending commands have
been completed or cancelled, avoiding this deadlock.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fail commands immediately when the request cannot be sent to the hardware.
This solves the following deadlock:
1. Two commands are in the queue.
2. The first command is sent, but causes a timeout, which kicks off an
asynchronous device reset
3. The second command is submitted to the device, and fails. The failure
is noted but the existing code waits for the timeout handler to take
care of the failure.
4. The device reset kicks in, causing the device "surprise removed" flag
to be set as the device disappears from the bus.
5. lbs_thread notes this and enters "adapter removed; waiting to die"
mode, without processing any further command timeouts.
While adjusting lbs thread logic to handle this situation may be one way
to fix this, it seems more practical to simplify handling of host_to_card
failure so that the commands are failed immediately without waiting for
more compliated timeout logic to kick in.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
reg_notifier can be called before the interface is up.
Handle this correctly by storing the requested country code, then
apply the relevant configuration when the interface is brought up.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
drivers/net/wireless/iwmc3200wifi/cfg80211.c
drivers/net/wireless/mwifiex/cfg80211.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the list of commands CMD_802_11_EEPROM_ACCESS had been
defined twice, unnecessarily, luckily with same value.
Remove one occurence.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().
Also describe the desired set_monitor_channel()
semantics more clearly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
Neatened the mwifiex_deauthenticate_infra function which
was doing odd things with array pointers and not using
is_zero_ether_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB 3.5-rc1 changes from Greg Kroah-Hartman:
"Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as
well. We deleted a staging driver, which was nice, and finally
dropped the obsolete usbfs code, which will make Al happy to never
have to touch that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were
due to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (477 commits)
xhci: Fix DIV_ROUND_UP compile error.
xhci: Fix compile with CONFIG_USB_SUSPEND=n
USB: Fix core compile with CONFIG_USB_SUSPEND=n
brcm80211: Fix compile error for .disable_hub_initiated_lpm.
Revert "USB: EHCI: work around bug in the Philips ISP1562 controller"
MAINTAINERS: Add myself as maintainer to the USB PHY Layer
USB: EHCI: fix command register configuration lost problem
USB: Remove races in devio.c
USB: ehci-platform: remove update_device
USB: Disable hub-initiated LPM for comms devices.
xhci: Add Intel U1/U2 timeout policy.
xhci: Add infrastructure for host-specific LPM policies.
USB: Add macros for interrupt endpoint types.
xhci: Reserve one command for USB3 LPM disable.
xhci: Some Evaluate Context commands must succeed.
USB: Disable USB 3.0 LPM in critical sections.
USB: Add support to enable/disable USB3 link states.
USB: Allow drivers to disable hub-initiated LPM.
USB: Calculate USB 3.0 exit latencies for LPM.
USB: Refactor code to set LPM support flag.
...
Conflicts:
arch/arm/mach-exynos/mach-nuri.c
arch/arm/mach-exynos/mach-universal_c210.c
drivers/net/wireless/ath/ath6kl/usb.c
|
|
Hub-initiated LPM is not good for USB communications devices. Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.
If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data. Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.
The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host. In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.
Set the disable_hub_initiated_lpm flag for for all USB communications
drivers. I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Do not assume we have our subsystem including this for us,
at least for older kernels this is not true. Lets just be
explicit about this requirement for the usage of wake_up().
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/iwlwifi/iwl-testmode.c
|
|
Fix merge between commit 3adadc08cc1e ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d27 ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without it, I get compile errors due to missing TASK_NORMAL,
TASK_UNINTERRUPTIBLE and schedule.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Daniel Drake <dsd@laptop.org>
Tested-by: Dan Williams <dcbw@redhat.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As described at
http://article.gmane.org/gmane.linux.kernel.wireless.general/86084
libertas is taking a long time to load because it loads firmware
during module loading.
Add a new API for interface drivers to load their firmware
asynchronously. The same semantics of the firmware table are followed
like before.
Interface drivers will be converted in follow-up patches, then we can
remove the old, synchronous firmware loading function.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
These simple sanity check avoids extra complexity in error paths when
moving to asynchronous firmware loading (which means the device may fail to
init some time after its creation).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove the ability to pass module parameters with firmware filenames
for USB and SDIO interfaces.
Remove the ability to pass custom "user" filenames to lbs_get_firmware().
Remove the ability to reprogram internal device memory with a different
firmware from the USB driver (we don't know of any users), and simplify
the OLPC firmware loading quirk to simply placing the OLPC firmware
at the top of the list (we don't know of any users other than OLPC).
Move lbs_get_firmware() into its own file.
These simplifications should have no real-life effect but make the
upcoming transition to asynchronous firmware loading considerably less
painful.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add a corresponding leave call on error failure.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Return type for lbs_auth_to_authtype() is changed from "u8" to
"int" to return negative error code correctly.
Also an error check is added in connect handler for invalid auth
type.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
release_firmware()
release_firmware() tests for, and deals gracefully with, NULL
pointers. Remove redundant explicit tests before calling the function.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/ath/ath9k/hw.c
|
|
libertas provides a dump_survey implementation based on reading of
a RSSI value. However, this RSSI value is calculated based on the
last received beacon from the associated AP - it is not a good
way of surveying a channel in general, and even causes an error
if the card is not associated to a network.
As this is not appropriate as a survey, remove it. This fixes an
issue where something in userspace is repeatedly calling site-survey
during boot, resulting in many repeated errors as the RSSI value cannot
be read before associating.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
