| Age | Commit message (Collapse) | Author |
|---|
|
The auto-arp feature of wl12xx allows the firmware to automatically
response to arp requests asking for its ip.
in order to use it, we configure the arp response template and
enable the corresponding bit in wl1271_acx_arp_filter (along with
passing its ip)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
Disabling the 11a channels when not supported in the reg_notify function was
not working as it should, because when the driver is initiailizing (and
registering itself with mac80211), it would get the reg notification too
early. At that point the driver wouldn't have received the NVS yet, so it
wouldn't know whether 11a was supported.
To fix this, we disable 11a channels when we read the NVS instead. Also, it
is easier (and still safe) to set n_channels to zero instead of setting the
disabled flag on every 11a channel.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
Because we don't support them at this stage.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
Use per-device debugfs path, so multiple devices won't collide.
in order to use wl->hw->wiphy->debugfsdir, we have to move the debugfs
creation from wl1271_debugfs_init() to wl1271_register_hw().
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
The probe-request template used in the hardware connection monitoring feature
thus far has been an empty one, without the SSID IE and without supported rate
IEs. This causes problems with some AP's.
Additionally, after connected scans, the template for connection maintenance
would remain to be the one last used for scanning - potentially incorrect.
Fix these by getting a pre-filled directed probe-request template for the
associated-to AP from mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
Instead of simply not scanning for the 11a channels when not supported by the
hardware, disable the channels in reg_notify. This centralizes the decision
on whether to scan 5GHz channel in one place and allows userspace to know
exactly which channels are in use.
Based on Juuso Oikarinen's idea.
Cc: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
|
|
It is possible that the op_remove_interface function is invoked exactly at
the same time has hw recovery is started. In this case it is possible for the
interface to be already removed in the op_remove_interface call, which
currently leads to a kernel warning and a subsequent kernel crash.
Fix this by ignoring the op_remove_interface call if the interface is already
down at that point.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
On the disassociation event from the mac80211, the wl12xx driver does not
clear the chipset configuration related to the AP - i.e. it does not perform
a DISCONNECT and then a JOIN with zero SSID and dummy BSSID. Also, it does not
unset the BSSID filter.
Often this is not a problem, as the above is performed upon entering idle
state. But if a scenario arises where a new association is attempted without
cycling through idle state, the new association will fail.
Fix this by resetting the firmware state on disassociation.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
Indicate to mac80211 we support HW fragmentation.
Support updates of the fragmentation threshold via the
set_frag_threshold callback.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
This reverts commit fa21c7a9e4be439e217fe72edbd39b643b643791.
The reverted patch caused more harm than benefit.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
The wl1271 does not support radar detection. Hence, prevent ad-hoc and
active scanning on frequencies requiring DFS.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
All files name prefix removed due to the fact that wl12xx driver supports
wl1271 and wl1273.
Also the definition in Kconfig and header files changed respectively.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
Now that all 1271 files are split, we can add wl1251_ prefix to the files.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We don't want to have any 1271 code in wl1251.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In preparation to split wl12xx to wl1251 and wl1271.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add implementation to use chipset specific join commands.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Check the return call from wl12xx_ps_elp_wakeup() and bail out if it
fails. This shouldn't happen, but if does there's a fundamental low
level issue.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The wakeup call was done too deep in code path, it's better to wakeup
chip from higher levels. This will also reduce wakeup calls significantly.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The function doesn't lock the mutex before sending the acx.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Moved wl1251 TX path implementation into chip specific files to enable
parallel implementation for the wl1271 TX path.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds the code that recognizes the new WL1271 chip revision (PG 2.0).
Full support for this chip is not yet implemented and support for WL1271 PG 1.0
is not guaranteed anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The chipset source interrupt source configuration during fw wakeup was
blocking interrupts on the wl1271. The configuration is effectively
unused here as it is used to trigger an interrupt for the chipset
wake-up event, which is not handled, or waited for, in the fw wakeup
anyway on either wl1251 or wl1271.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rx descriptor was incorrectly allocated from stack, use struct wl12xx
instead. Needed for DMA transfers.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Resources were not freed properly in some cases.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rework cmd and acx interfaces, it was just too confusing earlier. Now
all commands need to contain all the needed headers, either just cmd
headers or both cmd and acx headers. This accomplish to remove the
extra copy done for each command. The interfaces are now properly
documented as well.
Also try to make all commands safe for DMA transfers. I might have missed
some, but most of them should be fixed now.
And this is not all! As a free bonus you will also get some cosmetic
cleanups and code reorganisation. Order today!
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fixes warnings:
drivers/net/wireless/wl12xx/main.c:87: warning: int format, different
type arg (arg 2)
drivers/net/wireless/wl12xx/main.c: In function `wl12xx_fetch_nvs':
drivers/net/wireless/wl12xx/main.c:125: warning: int format, different
type arg (arg 2)
drivers/net/wireless/wl12xx/wl1251.c: In function 'wl1251_upload_firmware':
drivers/net/wireless/wl12xx/wl1251.c:94: warning: int format, different
type arg (arg 2)
drivers/net/wireless/wl12xx/wl1251.c:141: warning: int format, different
type arg (arg 2)
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
wl12xx is a driver for TI wl1251 802.11 chipset designed for embedded
devices, supporting both SDIO and SPI busses. Currently the driver
supports only SPI. Adding support 1253 (the 5 GHz version) should be
relatively easy. More information here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?contentId=4711&navigationId=12494&templateId=6123
(Collapsed original sequence of pre-merge patches into single commit for
initial merge. -- JWL)
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
