| Age | Commit message (Collapse) | Author |
|---|
|
All files name prefix removed due to the fact that wl12xx driver supports
wl1271 and wl1273.
Also the definition in Kconfig and header files changed respectively.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
While scanning, it is possible that beacon and probe response frames are
received on other band than configured to the driver. In rx status
handling this has caused "Unsupported RX rate from HW" warnings. This
patch changes the wl1271_rate_to_index function to take the band of the
received frame as a parameter instead of using value configuret to
wl->band.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
While wl1271_irq_work handles RX directly (by calling wl1271_rx), a different
work is scheduled for transmitting packets. The IRQ work might handle more than
one interrupt during a single call, including multiple TX completion
interrupts. This might starve TX, since no packets are transmitted until all
interrupts are handled.
Fix this by calling the TX work function directly, instead of deferring
it.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
Incorrect TID was configured for TX frames. This resulted in incorrect
queues to be used for classes in transmission.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
Conflicts:
drivers/net/wireless/wl12xx/wl1271.h
drivers/net/wireless/wl12xx/wl1271_cmd.h
|
|
cleanup patch.
Use new __packed annotation in drivers/net/
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mac80211 changes to idle almost immediately after transmitting some
frames, such as deauth etc. When going to idle, the wl1271 is disconnected,
which causes TX frames already on buffers, but not yet transmitted, to be
deleted.
To make sure deauth frames reach the air, allow the TX buffers to flush
before proceeding to idle.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently the mac80211 is not telling a hardware rate controlled driver a
rate to use for association frames etc. So to be safe, use the lowest rate
of each band for communication.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add reporting of the used TX rate to mac80211 in the tx_status.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Everything is ready now and we can enable WMM in wl1271.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch simplifies the required block count calculation. Though it
introduces a division operator, it greatly simplifies the formula.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
- Fix a TX result overflow problem that was present in the TX path and visible
with at least linksys AP's (probably any AP with high throughput capability.)
- Optimize TX by writing FW trigger for a group of TX frames instead of
each and every frame.
- Slightly optimize the TX path code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Now that necessary commands for WMM are implemented, implement queue handling
for WMM. But WMM is not enabled yet, only one queue is used.
Based on a similar patch from wl1251.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We were not handling endianess correctly. The wl1271 chip runs on
little-endian values. This patch makes sure that all the communication with
the wl1271 firmware is done in little-endian by using cpu_to_le* and
le*_to_cpu where appropriate.
Also, all the struct definitions for data exchanged with the firmware has
been changed to use __le16/32 types instead of u16/32.
This fixes a few sparse warnings, such as these:
drivers/net/wireless/wl12xx/wl1271_cmd.c:554:42: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:555:42: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:577:58: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:579:58: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:676:18: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:787:22: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_cmd.c:789:21: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_tx.c:98:47: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/wl12xx/wl1271_acx.c:932:32: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_boot.c:191:32: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/wl12xx/wl1271_boot.c:197:38: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/wl12xx/wl1271_boot.c:199:37: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/wl12xx/wl1271_init.c:255:40: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1271_init.c:275:53: warning: incorrect type in assignment (different base types)
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This driver supports the wl1271 chipset from Texas Instruments based on the
WiLink(tm) 6.0 mobile platform. Support for wl1273 should be relatively easy
to add. This chipset is designed for embedded devices, with good powersaving
capabilities. The wl1271 chipset is the successor of wl1251 and supports the
802.11b/g/n standards, but currently this driver supports only b/g.
More information about this chipset can be found here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12762&contentId=29993
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
