summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/wl12xx
AgeCommit message (Collapse)Author
2011-10-07wl12xx: disable AP-mode-specific quirksEliad Peller
The current wl12xx fw (7.3.0.0.77) supports both STA and AP mode, and we no longer use AP-mode-specific quirks. WL12XX_QUIRK_END_OF_TRANSACTION is still used for certain HWs, while WL12XX_QUIRK_LPD_MODE is not used anymore. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-07wl12xx: Add support for HW channel switchShahar Levi
The wl12xx FW supports HW channel switch. If we don't use it, sometimes the firmware gets confused when recalibrating to the new channel, causing RX problems. This commit adds HW channel switch support by implementing the channell_switch op. Signed-off-by: Shahar Levi <shahar_levi@ti.com> [added one comment, remove the tx_flush and rephrased the commit message] Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-07wl12xx: set max_sched_scan_ie_len correctlyLuciano Coelho
The wiphy max_sched_scan_ie_len attribute was not set correctly and remained as 0, so when IEs were being passed in a scheduled scan, we were returning -EINVAL. Fix this by setting the attribute properly. Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-07wl12xx: configure rate policy for p2p operationsEliad Peller
p2p packets should go out only with OFDM rates. Configure a new rate policy that will (later) be used during p2p_find (when the p2p_cli / p2p_go interfaces are in use, we won't have to use this policy, as the configured rates should already be OFDM-only). Additionally, update CONF_TX_MAX_RATE_CLASSES to reflect the current value from the fw api. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-03mac80211: pass vif param to conf_tx() callbackEliad Peller
tx params should be configured per interface. add ieee80211_vif param to the conf_tx callback, and change all the drivers that use this callback. The following spatch was used: @rule1@ struct ieee80211_ops ops; identifier conf_tx_op; @@ ops.conf_tx = conf_tx_op; @rule2@ identifier rule1.conf_tx_op; identifier hw, queue, params; @@ conf_tx_op ( - struct ieee80211_hw *hw, + struct ieee80211_hw *hw, struct ieee80211_vif *vif, u16 queue, const struct ieee80211_tx_queue_params *params) {...} Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27mac80211: add ieee80211_vif param to tsf functionsEliad Peller
TSF can be kept per vif. Add ieee80211_vif param to set/get/reset_tsf, and move the debugfs entries to the per-vif directory. Update all the drivers that implement these callbacks. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-23wl12xx: report the stop_ba event to all STAs in AP-modeArik Nemtsov
Use the AP_MAX_LINKS as the upper boundary for traversing the links array, thereby guaranteeing BA sessions with all connected STAs are stopped when the stop_ba event is received. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-23wl12xx: correct fw_status structure for 8 sta support in AP-modeArik Nemtsov
Fix an erroneous labeling of array boundaries in the fw_status structure. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-23wl12xx: implement set_bitrate_mask callbackEliad Peller
Save the configured bitrate, and use the min allowed rate as the basic rate (e.g. when scanning). Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-23wl12xx: AP mode - support hidden SSIDArik Nemtsov
If a hidden SSID is requested, generate a probe response template containing the real SSID. Depends on the patch "mac80211: add ssid config to bss information in AP-mode". Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-23wl12xx: Use dev_hlid for auth and assoc reqEliad Peller
On roaming, the auth and assoc req are sent with the sta hlid. This is wrong, as the sta hlid is configured according to the old ap. Use the dev_hlid instead. Move the wl1271_tx_update_filters() call into wl1271_tx_get_hlid(), so wl->dev_hlid will be valid. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-23wl12xx: send all pending packets on channel changeEliad Peller
There is a race condition between wl1271_tx_work() and the channel switch, so make sure all the pending packets are being sent before switching channel. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-23wl12xx: remove P2P ie from probe responseEliad Peller
wl12xx uses a single probe response template, regardless of the probe request. However, the P2P spec forbids including the p2p ie in some cases (e.g. the probe request didn't include the p2p ie). The fw responds only to probe requests that don't include the p2p ie, and passes up probe requests that include them (the supplicant will answer them). Thus, strip the p2p ie from the probe response template. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-23wl12xx: remove TIM ie from probe responseEliad Peller
wl12xx uses the beacon as the probe response template. However, the beacon includes a TIM ie, which shouldn't exist in the probe response. Delete it from the skb before configuring the probe response template. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-23wl12xx: Include OFDM rates in IBSS modeShahar Levi
We were including only 11b rates in IBSS mode. This patch adds OFDM rates. [Rephrased commit log and removed one unnecessary comment. -- Luca] Signed-off-by: Shahar Levi <shahar_levi@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-23wl12xx: fix sdio_test module functionalityShahar Levi
Due to some changes in PM in recent kernels, the sdio_test module has been broken for a while. This patch fixes the code that powers the card on and off. Also made some small indentation fixes in the Makefile. [Rephrased commit log and removed the change in the FW name, since it's done in another patch. -- Luca] Signed-off-by: Shahar Levi <shahar_levi@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-22wl12xx: fix forced passive scansLuciano Coelho
We were using incorrect max and min dwell times during forced passive scans because we were still using the active scan states to scan (passively) the channels that were not marked as passive. Instead of doing passive scans in active states, we now skip active states and scan for all channels in passive states. Cc: <stable@kernel.org> # 2.6.36+ Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-20Merge branch 'master' of git://git.infradead.org/users/linville/wirelessJohn W. Linville
Conflicts: drivers/net/wireless/iwlwifi/iwl-pci.c drivers/net/wireless/iwlwifi/iwl-trans-pcie-tx.c drivers/net/wireless/rt2x00/rt2800usb.c drivers/net/wireless/wl12xx/main.c
2011-09-14wl12xx: support p2p interfacesEliad Peller
Declare support for p2p interfaces, and create p2p_cli/p2p_go roles when being asked for. Indicate we are using a p2p interface by setting the wl->p2p flag. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: set mac80211 flags for A-MPDU aggregation supportArik Nemtsov
We set the mac80211 flag for A-MPDU support and also indicate that Tx-agg session setup is performed in HW. This patch depends on "mac80211: add flag to indicate HW only Tx-agg setup support" Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: AP mode - clean BA and queue state in tx_resetArik Nemtsov
Reset the BA state of all connected stations and explicitly clear the Tx queues. The latter is needed for clearing dummy packets from tx_queue_count. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: AP mode - enable the BA constraint event from the FWArik Nemtsov
Unblock the RX BA constraint event from firmware in AP mode as well. This allows us to stop RX BA sessions when the FW requests it. In addition refactor the handler for this event to make the flow clearer. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: don't regulate links when a single STA is connectedArik Nemtsov
When operating as AP track the number of connected stations. When a single STA is connected don't regulate the PS status of the link. Since this is the only STA connected, there's no point holding space in FW for other links. This will speed up communications with a single connected STA in PSM. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: support up to 8 stations in AP-modeArik Nemtsov
Change the max number of AP stations to 8, up from 5. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: AP mode - don't regulate FW blocks for non-active STAsArik Nemtsov
Check a STA is associated before regulating its PS-status in mac80211. Should never happen, so warn as a precaution. [Small cosmetic change wrt Kalle Valo's comment. -- Luca] Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: don't indicate up PS-filtered dummy packetsArik Nemtsov
Dummy packets are currently only sent on the system_hlid link. The system_hlid link should never be filtered for PS (as it is not a STA link). Even so, for correctness, don't indicate dummy packets up. The skb does not belong to mac80211 and as such does not contain a correct skb->cb. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: ignore sched scan match sets without SSIDLuciano Coelho
For now, cfg80211 only support match sets with SSIDs, but in the future more parameters will be added. This patch ignores eventual matches that do not contain SSIDs in preparation for the future. This change also affects the case where broadcast SSIDs are used. Matching a broadcast SSID will match everything, so they can be ignored. Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: increase number of allowed SSIDs in sched_scanLuciano Coelho
The latest firmware supports up to 16 SSIDs in the scheduled scan lists. Increase the number we report to cfg80211 and increase the min/max dwell time to 30 and 60 TUs respectively, because otherwise we don't have the time to send the probes for all SSIDs. Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: add support for sched_scan filtersLuciano Coelho
Implement support for filtering in scheduled scans. With this commit we now use the match sets passed by cfg80211 to filter on SSIDs. Due to the nature of the wl12xx firmware API, we don't allow SSIDs to be sent in the probe requests if they are not going to match any of the filters. Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: declare support for WIPHY_FLAG_AP_UAPSDEliad Peller
Declare support for uapsd when working as AP, and set psd_type and sp_len whan a station is being added. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: use kstrtoul_from_userEliad Peller
simplify code by calling kstrtoul_from_user() (instead of copy_from_user() + kstrtoul()) Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: remove deprecated CONFIG_WL12XX_HT flagLuciano Coelho
The driver now support HT properly, so we can always have HT enabled. Remove the WL12XX_HT configuration. Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: don't queue a new dummy packet if one is already pendingArik Nemtsov
The firmware only asks for one dummy packet at a time, but sometimes we are unable to provide it before a FW timer expires. When this happens, the FW will re-request the dummy packet. If a packet is still queued in the driver queues, do nothing in this case. This prevents spurious dummy packets from clogging up the VO AC. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: add config_hangover commandEliad Peller
Add wl12xx_acx_config_hangover() and respective conf values. This command configures how long the chip will stay awake after it was configured to enter psm. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: check for ROC on scan_completeEliad Peller
When scan completes, and we are not associated, we should start the dev role and ROC. however, we might already be in this situation (e.g. if we got disconnected during scan). check for it. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: don't use WL1271_SCAN_OPT_PRIORITY_HIGH flagEliad Peller
When setting the WL1271_SCAN_OPT_PRIORITY_HIGH flag, the driver requests a scan *now*, and the fw doesn't enter psm before scanning, which in turn might cause packets loss. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: don't disconnect on recoveryEliad Peller
allow full connection recovery by dropping the beacon_loss notification. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: add beacon_filtering debugfs fileEliad Peller
Allow enabling/disabling beacon_filtering by debugfs, in order to reduce the log size while debugging (beacon filtering is disabled by default in AP mode, as beacons are needed for ERP configuration). Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: add module_param to trigger BUG() on recoveryEliad Peller
Crashing on recovery is useful for debugging, as a JTAG can be connected in order to investigate the current fw state. (otherwise, a reconfiguration will occur) Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: print the seq_num of rx packetEliad Peller
Make it easier to match the driver log against a sniffer log. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14wl12xx: print acx idEliad Peller
Add id param to the acx debug print (on wl1271_cmd_configure) Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-09-14Merge branch 'wl12xx-next' into for-linvilleLuciano Coelho
2011-08-29wl12xx/sdio_test.c: fix build breakage from WL127X_FW_NAME changeJohn W. Linville
Commit c302b2c959164622558474871ae942da0e484a38 ("wl12xx: Use a single fw for both STA and AP roles") changed the name of the firmware name definition, breaking the build of wl12xx/sdio_test.c. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-08-25wl12xx: use SCAN_SSID_TYPE_PUBLIC when using the wildcard in sched_scanLuciano Coelho
When we are scanning for the wildcard SSID in a scheduled scan, we should use SCAN_SSID_TYPE_PUBLIC so that we don't filter out the scan results. Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-08-25wl12xx: add support for multiple SSIDs in sched_scanLuciano Coelho
The wl12xx firmwares support multiple SSIDs in a single sched_scan run. This patch implements support for it. We use three different types os sched_scan: FILTER_ANY (ie. not filtering, only wildcard SSID in the probe_reqs); FILTER_LIST (ie. send out probe_reqs with the specified SSIDs and only report if they are found); and FILTER_DISABLED (ie. send out probe_reqs with the specified SSIDs, but report anything found). Since we still don't have proper filter support in nl80211/cfg80211 yet, we cannot use filters when the wildcard SSID is used. Thus, we will not filter anything if the wildcard SSID is specified. Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-08-25wl12xx: enter psm only after station role was startedEliad Peller
The station didn't get into psm after recovery, because psm was configured before sta role was started. Move wl1271_ps_set_mode() to be executed only after the role was started. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-08-25wl12xx: increase psm_entry_retriesEliad Peller
In congested env, sometimes 5 psm entry retries are not enough. Increase the retries count to 8. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-08-25wl12xx: initialize rate_set on band rates initializationEliad Peller
In some corner cases, (invalid) 11g rates were used while working on 11a band. Take care of it by initializing rate_set according to the configured band. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-08-25wl12xx: allow 11a AP-mode for wl127x devicesArik Nemtsov
There was a check preventing 127x devices from using the 11a band when operating as AP. Since we now support this functionality, remove the check. With this patch, a 11a AP starts ok on 127x cards. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-08-25wl12xx: use 2 spare TX blocks for GEM cipherGuy Eilam
Add tx_spare_blocks member to the wl1271 struct for more generic configuration of the amount of spare TX blocks that should be used. The default value is 1. In case GEM cipher is used by the STA, we need 2 spare TX blocks instead of just 1. Signed-off-by: Guy Eilam <guy@wizery.com> Acked-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-01-24 17:58:15 +0000