summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/zd1211rw
AgeCommit message (Collapse)Author
2013-03-25mac80211: Use a cfg80211_chan_def in ieee80211_hw_conf_chanKarl Beldan
Drivers that don't use chanctxes cannot perform VHT association because they still use a "backward compatibility" pair of {ieee80211_channel, nl80211_channel_type} in ieee80211_conf and ieee80211_local. Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com> [fix kernel-doc] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-21Merge tag 'driver-core-3.9-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core patches from Greg Kroah-Hartman: "Here is the big driver core merge for 3.9-rc1 There are two major series here, both of which touch lots of drivers all over the kernel, and will cause you some merge conflicts: - add a new function called devm_ioremap_resource() to properly be able to check return values. - remove CONFIG_EXPERIMENTAL Other than those patches, there's not much here, some minor fixes and updates" Fix up trivial conflicts * tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits) base: memory: fix soft/hard_offline_page permissions drivercore: Fix ordering between deferred_probe and exiting initcalls backlight: fix class_find_device() arguments TTY: mark tty_get_device call with the proper const values driver-core: constify data for class_find_device() firmware: Ignore abort check when no user-helper is used firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER firmware: Make user-mode helper optional firmware: Refactoring for splitting user-mode helper code Driver core: treat unregistered bus_types as having no devices watchdog: Convert to devm_ioremap_resource() thermal: Convert to devm_ioremap_resource() spi: Convert to devm_ioremap_resource() power: Convert to devm_ioremap_resource() mtd: Convert to devm_ioremap_resource() mmc: Convert to devm_ioremap_resource() mfd: Convert to devm_ioremap_resource() media: Convert to devm_ioremap_resource() iommu: Convert to devm_ioremap_resource() drm: Convert to devm_ioremap_resource() ...
2013-02-04wireless: Remove unnecessary alloc/OOM messages, alloc cleanupsJoe Perches
alloc failures already get standardized OOM messages and a dump_stack. Convert kzalloc's with multiplies to kcalloc. Convert kmalloc's with multiplies to kmalloc_array. Remove now unused variables. Remove unnecessary memset after kzalloc->kcalloc. Whitespace cleanups for these changes. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-22drivers/net/wireless/zd1211rw: remove depends on CONFIG_EXPERIMENTALKees Cook
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a while now and is almost always enabled by default. As agreed during the Linux kernel summit, remove it from any "depends on" lines in Kconfigs. CC: Ulrich Kunitz <kune@deine-taler.de> Acked-by: John W. Linville <linville@tuxdriver.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-19treewide: fix typo of "suppport" in various commentsMasanari Iida
Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-10-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
Pull networking changes from David Miller: 1) GRE now works over ipv6, from Dmitry Kozlov. 2) Make SCTP more network namespace aware, from Eric Biederman. 3) TEAM driver now works with non-ethernet devices, from Jiri Pirko. 4) Make openvswitch network namespace aware, from Pravin B Shelar. 5) IPV6 NAT implementation, from Patrick McHardy. 6) Server side support for TCP Fast Open, from Jerry Chu and others. 7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel Borkmann. 8) Increate the loopback default MTU to 64K, from Eric Dumazet. 9) Use a per-task rather than per-socket page fragment allocator for outgoing networking traffic. This benefits processes that have very many mostly idle sockets, which is quite common. From Eric Dumazet. 10) Use up to 32K for page fragment allocations, with fallbacks to smaller sizes when higher order page allocations fail. Benefits are a) less segments for driver to process b) less calls to page allocator c) less waste of space. From Eric Dumazet. 11) Allow GRO to be used on GRE tunnels, from Eric Dumazet. 12) VXLAN device driver, one way to handle VLAN issues such as the limitation of 4096 VLAN IDs yet still have some level of isolation. From Stephen Hemminger. 13) As usual there is a large boatload of driver changes, with the scale perhaps tilted towards the wireless side this time around. Fix up various fairly trivial conflicts, mostly caused by the user namespace changes. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits) hyperv: Add buffer for extended info after the RNDIS response message. hyperv: Report actual status in receive completion packet hyperv: Remove extra allocated space for recv_pkt_list elements hyperv: Fix page buffer handling in rndis_filter_send_request() hyperv: Fix the missing return value in rndis_filter_set_packet_filter() hyperv: Fix the max_xfer_size in RNDIS initialization vxlan: put UDP socket in correct namespace vxlan: Depend on CONFIG_INET sfc: Fix the reported priorities of different filter types sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP sfc: Fix loopback self-test with separate_tx_channels=1 sfc: Fix MCDI structure field lookup sfc: Add parentheses around use of bitfield macro arguments sfc: Fix null function pointer in efx_sriov_channel_type vxlan: virtual extensible lan igmp: export symbol ip_mc_leave_group netlink: add attributes to fdb interface tg3: unconditionally select HWMON support when tg3 is enabled. Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT" gre: fix sparse warning ...
2012-09-11zd1211rw: enable support for MFPJussi Kivilinna
zd1211rw lacks hardware encryption, so enabling 802.11w is only matter of enabling IEEE80211_HW_MFP_CAPABLE flag. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-13workqueue: use mod_delayed_work() instead of cancel + queueTejun Heo
Convert delayed_work users doing cancel_delayed_work() followed by queue_delayed_work() to mod_delayed_work(). Most conversions are straight-forward. Ones worth mentioning are, * drivers/edac/edac_mc.c: edac_mc_workq_setup() converted to always use mod_delayed_work() and cancel loop in edac_mc_reset_delay_period() is dropped. * drivers/platform/x86/thinkpad_acpi.c: No need to remember whether watchdog is active or not. @fan_watchdog_active and related code dropped. * drivers/power/charger-manager.c: Seemingly a lot of delayed_work_pending() abuse going on here. [delayed_]work_pending() are unsynchronized and racy when used like this. I converted one instance in fullbatt_handler(). Please conver the rest so that it invokes workqueue APIs for the intended target state rather than trying to game work item pending state transitions. e.g. if timer should be modified - call mod_delayed_work(), canceled - call cancel_delayed_work[_sync](). * drivers/thermal/thermal_sys.c: thermal_zone_device_set_polling() simplified. Note that round_jiffies() calls in this function are meaningless. round_jiffies() work on absolute jiffies not delta delay used by delayed_work. v2: Tomi pointed out that __cancel_delayed_work() users can't be safely converted to mod_delayed_work(). They could be calling it from irq context and if that happens while delayed_work_timer_fn() is running, it could deadlock. __cancel_delayed_work() users are dropped. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Acked-by: David Howells <dhowells@redhat.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Doug Thompson <dougthompson@xmission.com> Cc: David Airlie <airlied@linux.ie> Cc: Roland Dreier <roland@kernel.org> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Len Brown <len.brown@intel.com> Cc: "J. Bruce Fields" <bfields@fieldses.org> Cc: Johannes Berg <johannes@sipsolutions.net>
2012-07-31mac80211: move TX station pointer and restructure TXThomas Huehn
Remove the control.sta pointer from ieee80211_tx_info to free up sufficient space in the TX skb control buffer for the upcoming Transmit Power Control (TPC). Instead, the pointer is now on the stack in a new control struct that is passed as a function parameter to the drivers' tx method. Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de> Signed-off-by: Alina Friedrichsen <x-alina@gmx.net> Signed-off-by: Felix Fietkau <nbd@openwrt.org> [reworded commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-06wireless: Remove casts to same typeJoe Perches
Adding casts of objects to the same type is unnecessary and confusing for a human reader. For example, this cast: int y; int *p = (int *)&y; I used the coccinelle script below to find and remove these unnecessary casts. I manually removed the conversions this script produces of casts with __force, __iomem and __user. @@ type T; T *p; @@ - (T *)p + p Neatened the mwifiex_deauthenticate_infra function which was doing odd things with array pointers and not using is_zero_ether_addr. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-18USB: Disable hub-initiated LPM for comms devices.Sarah Sharp
Hub-initiated LPM is not good for USB communications devices. Comms devices should be able to tell when their link can go into a lower power state, because they know when an incoming transmission is finished. Ideally, these devices would slam their links into a lower power state, using the device-initiated LPM, after finishing the last packet of their data transfer. If we enable the idle timeouts for the parent hubs to enable hub-initiated LPM, we will get a lot of useless LPM packets on the bus as the devices reject LPM transitions when they're in the middle of receiving data. Worse, some devices might blindly accept the hub-initiated LPM and power down their radios while they're in the middle of receiving a transmission. The Intel Windows folks are disabling hub-initiated LPM for all USB communications devices under a xHCI USB 3.0 host. In order to keep the Linux behavior as close as possible to Windows, we need to do the same in Linux. Set the disable_hub_initiated_lpm flag for for all USB communications drivers. I know there aren't currently any USB 3.0 devices that implement these class specifications, but we should be ready if they do. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Hansjoerg Lipp <hjlipp@web.de> Cc: Tilman Schmidt <tilman@imap.cc> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Jan Dumon <j.dumon@option.com> Cc: Petko Manolov <petkan@users.sourceforge.net> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com> Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Brett Rudley <brudley@broadcom.com> Cc: Roland Vossen <rvossen@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Kan Yan <kanyan@broadcom.com> Cc: Dan Williams <dcbw@redhat.com> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Herton Ronaldo Krzesinski <herton@canonical.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Cc: Daniel Drake <dsd@gentoo.org> Cc: Ulrich Kunitz <kune@deine-taler.de> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-03-20Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial Pull trivial tree from Jiri Kosina: "It's indeed trivial -- mostly documentation updates and a bunch of typo fixes from Masanari. There are also several linux/version.h include removals from Jesper." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits) kcore: fix spelling in read_kcore() comment constify struct pci_dev * in obvious cases Revert "char: Fix typo in viotape.c" init: fix wording error in mm_init comment usb: gadget: Kconfig: fix typo for 'different' Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c" writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header writeback: fix typo in the writeback_control comment Documentation: Fix multiple typo in Documentation tpm_tis: fix tis_lock with respect to RCU Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c" Doc: Update numastat.txt qla4xxx: Add missing spaces to error messages compiler.h: Fix typo security: struct security_operations kerneldoc fix Documentation: broken URL in libata.tmpl Documentation: broken URL in filesystems.tmpl mtd: simplify return logic in do_map_probe() mm: fix comment typo of truncate_inode_pages_range power: bq27x00: Fix typos in comment ...
2012-02-29zd1211rw: wait between setting hash table and powering radio onFlorian Fainelli
I am running Debian testing kernel 3.1.0-1-amd64, using a 079b:0062 Sagem XG-76NA 802.11bg stick. Upon zd1211rw interface bringup (ifconfig wlan0 up) I get the following timeout: [ 950.330573] zd1211rw 1-3:1.0: phy2 [ 955.108510] zd1211rw 1-3:1.0: firmware version 4725 [ 955.148532] zd1211rw 1-3:1.0: zd1211b chip 079b:0062 v4810 high 00-19-70 AL2230_RF pa0 g--NS [snip] [ 955.204072] zd1211rw 1-3:1.0: error ioread32(CR_REG1): -110 A second ifconfig wlan0 up brings the interface up without problems. After a bit more debugging, the call trace is the following: [10241.028130] zd1211rw 1-3:1.0: zd_chip_lock_phy_regs: error ioread32(CR_REG1): -110 [10241.028140] zd1211rw 1-3:1.0: zd_switch_radio_on: failed to lock PHY regs [10241.028148] zd1211rw 1-3:1.0: zd_op_start: failed to set radio on Adding a 10 milliseconds delay between the call to set_mc_hash() and zd_chip_switch_radio_on() allows successful interface bringups in all cases and matches what the vendor driver did. Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-10zd1211rw: Fix typo in zd_usb.c and zd_mac.cMasanari Iida
Correct spelling "reseting" to "resetting" in drivers/net/wireless/zd1211rw/zd_usb.c drivers/net/wireless/zd1211rw/zd_mac.c Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-02-07zd1211rw: firmware needs duration_id set to zero for non-pspoll framesTomas Vanek
Some devices (iwl5100) cannot connect to zd1211rw based AP. It appears that zd1211 firmware messes up duration_id field if it is not set to zero by driver. Sniffing traffic shows that zd1211 is transmitting frames with duration_id bits 14 and 15 set and other bits appearing random. Setting duration_id at driver to zero results zd1211 outputting sane duration_id. This means that firmware is setting correct values itself and expects duration_id to be zero in first place. Looking at vendor driver shows that only PSPoll frames have duration_id set by driver, for other frames duration_id left zero. Original bug-report and attached patch at: http://sourceforge.net/mailarchive/message.php?msg_id=28759111 Reported-by: Tomas Vanek <Tomas.Vanek@fbl.cz> [modified original patch from bug-report, added check for pspoll frame] Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-31drivers/net: Add module.h to drivers who were implicitly using itPaul Gortmaker
The device.h header was including module.h, making it present for most of these drivers. But we want to clean that up. Call out the include of module.h in the modular network drivers. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-09-27mac80211: add ieee80211_vif param to tsf functionsEliad Peller
TSF can be kept per vif. Add ieee80211_vif param to set/get/reset_tsf, and move the debugfs entries to the per-vif directory. Update all the drivers that implement these callbacks. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: detect stalled beacon interrupt fasterJussi Kivilinna
As USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS, beacon interrupt (CR_INTERRUPT) might be lost. Problem is that when device trigger CR_INTERRUPT it disables HW interrupt. Now if USB_INT_ID_REGS with CR_INTERRUPT gets lost, beacon interrupt stays disabled until beacon watchdog notices the stall. This happen very often on heavy TX. Improve watchdog to trigger earlier, after three missing beacon interrupts. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: don't let zd_mac_config_beacon() run too long from beacon ↵Jussi Kivilinna
interrupt handler zd_mac_config_beacon() has only limited time to set up beacon when called from beacon interrupt handler/worker. So do not let it retry acquiring beacon fifo semaphore in interrupt handler. Beacon fifo semaphore should not be locked by firmware anyway at this time, it's only locked when device is using/txing beacon. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: handle lost read-reg interruptsJussi Kivilinna
Device losses read-reg interrupts. By looking at usbmon it appears that USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS. This causes read command to timeout, usually under heavy TX. Fix by retrying read registers again if USB_INT_ID_RETRY_FAILED is received while waiting for USB_INT_ID_REGS. However USB_INT_ID_REGS is not always lost but is received after USB_INT_ID_RETRY_FAILED and is usually received by the retried read command. USB_INT_ID_REGS of the retry is then left unhandled and might be received by next read command. Handle this by ignoring previous USB_INT_ID_REGS that doesn't match current read command request. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: only update HW beacon if new beacon differs from currectJussi Kivilinna
Update HW beacon only when needed. This appears to make device work in AP-mode (dtim_period=1) somewhat more stable. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: make 'handle_rx_packet: invalid, small RX packet' message debug-onlyJussi Kivilinna
This message is should be debug-only as it tells almost nothing useful. It also happens very often and just floods logs. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22zd1211rw: fix invalid signal values from deviceJussi Kivilinna
Driver uses IEEE80211_HW_SIGNAL_UNSPEC and so signal values reported to mac80211 should be in range 0..100. Sometimes device return out of range values. These out of range values can then trigger warning in cfg80211_inform_bss_frame. This patch adds checks to enforce range returned from driver to mac80211 be in 0..100 range. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-20zd1211rw: include mac80211.h from zd_chip.hKalle Valo
zd_chip.h contains one function with a pointer to ieee80211_hw but doesn't include mac80211.h. As a temporary solution include mac80211.h to avoid a warning. Signed-off-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-31zd1211rw: fix to work on OHCIJussi Kivilinna
zd1211 devices register 'EP 4 OUT' endpoint as Interrupt type on USB 2.0: Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 However on USB 1.1 endpoint becomes Bulk: Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Commit 37939810b937aba830dd751291fcdc51cae1a6cb assumed that endpoint is always interrupt type and changed usb_bulk_msg() calls to usb_interrupt_msg(). Problem here is that usb_bulk_msg() on interrupt endpoint selfcorrects the call and changes requested pipe to interrupt type (see usb_bulk_msg). However with usb_interrupt_msg() on bulk endpoint does not correct the pipe type to bulk, but instead URB is submitted with interrupt type pipe. So pre-2.6.39 used usb_bulk_msg() and therefore worked with both endpoint types, however in 2.6.39 usb_interrupt_msg() with bulk endpoint causes ohci_hcd to fail submitted URB instantly with -ENOSPC and preventing zd1211rw from working with OHCI. Fix this by detecting endpoint type and using correct endpoint/pipe types for URB. Also fix asynchronous zd_usb_iowrite16v_async() to use right URB type on 'EP 4 OUT'. Cc: stable@kernel.org Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-12Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem Conflicts: drivers/net/wireless/ath/ar9170/main.c drivers/net/wireless/ath/ar9170/phy.c drivers/net/wireless/zd1211rw/zd_rf_rf2959.c
2011-04-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits) net: Add support for SMSC LAN9530, LAN9730 and LAN89530 mlx4_en: Restoring RX buffer pointer in case of failure mlx4: Sensing link type at device initialization ipv4: Fix "Set rt->rt_iif more sanely on output routes." MAINTAINERS: add entry for Xen network backend be2net: Fix suspend/resume operation be2net: Rename some struct members for clarity pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev dsa/mv88e6131: add support for mv88e6085 switch ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2) be2net: Fix a potential crash during shutdown. bna: Fix for handling firmware heartbeat failure can: mcp251x: Allow pass IRQ flags through platform data. smsc911x: fix mac_lock acquision before calling smsc911x_mac_read iwlwifi: accept EEPROM version 0x423 for iwl6000 rt2x00: fix cancelling uninitialized work rtlwifi: Fix some warnings/bugs p54usb: IDs for two new devices wl12xx: fix potential buffer overflow in testmode nvs push zd1211rw: reset rx idle timer from tasklet ...
2011-04-07Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 Conflicts: drivers/net/wireless/rtlwifi/efuse.c drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c net/bluetooth/mgmt.c
2011-04-07zd1211rw: rename CR* macros to ZD_CR*Jussi Kivilinna
With compat-wireless CR* macros in zd_usb.h conflict with CR macros in include/asm-generic/termbits.h. So rename CR* macros to ZD_CR*. Conversion was done with using sed and then 'over 80 character line' checkpatch.pl warnings and comment indents were fixed. Reported-by: Walter Goldens <goldenstranger@yahoo.com> Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-04zd1211rw: reset rx idle timer from taskletJussi Kivilinna
2.6.38 added WARN_ON(in_irq) in del_timer_sync that triggers on zd1211rw when reseting rx idle timer in urb completion handler. Move timer reseting to tasklet. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-04zd1211rw: remove URB_SHORT_NOT_OK flag in zd_usb_iowrite16v_async()Jussi Kivilinna
Patch removes the bogus flag introduced by upstream commit eefdbec1ea8b7093d2c09d1825f68438701723cf. Old code had buffer length check that new code tried to handle with URB_SHORT_NOT_OK flag. With USB debugging enabled bogus flag caused usb_submit_urb fail. Remove URB_SHORT_NOT_OK flag and add buffer length check to urb completion handler. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32092 Reported-by: Jonathan Callen <abcd@gentoo.org> Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-31Fix common misspellingsLucas De Marchi
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-25Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits) route: Take the right src and dst addresses in ip_route_newports ipv4: Fix nexthop caching wrt. scoping. ipv4: Invalidate nexthop cache nh_saddr more correctly. net: fix pch_gbe section mismatch warning ipv4: fix fib metrics mlx4_en: Removing HW info from ethtool -i report. net_sched: fix THROTTLED/RUNNING race drivers/net/a2065.c: Convert release_resource to release_region/release_mem_region drivers/net/ariadne.c: Convert release_resource to release_region/release_mem_region bonding: fix rx_handler locking myri10ge: fix rmmod crash mlx4_en: updated driver version to 1.5.4.1 mlx4_en: Using blue flame support mlx4_core: reserve UARs for userspace consumers mlx4_core: maintain available field in bitmap allocator mlx4: Add blue flame support for kernel consumers mlx4_en: Enabling new steering mlx4: Add support for promiscuous mode in the new steering model. mlx4: generalization of multicast steering. mlx4_en: Reporting HW revision in ethtool -i ...
2011-03-21zd1211rw: TrendNet TEW-509UB id addedTõnu Samuel
Signed-off-by: Tõnu Samuel <tonu@jes.ee> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-20Merge branch 'trivial' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6 * 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits) video: change to new flag variable scsi: change to new flag variable rtc: change to new flag variable rapidio: change to new flag variable pps: change to new flag variable net: change to new flag variable misc: change to new flag variable message: change to new flag variable memstick: change to new flag variable isdn: change to new flag variable ieee802154: change to new flag variable ide: change to new flag variable hwmon: change to new flag variable dma: change to new flag variable char: change to new flag variable fs: change to new flag variable xtensa: change to new flag variable um: change to new flag variables s390: change to new flag variable mips: change to new flag variable ... Fix up trivial conflict in drivers/hwmon/Makefile
2011-03-17net: change to new flag variablematt mooney
Replace EXTRA_CFLAGS with ccflags-y. Signed-off-by: matt mooney <mfm@muteddisk.com> Acked-by: WANG Cong <xiyou.wangcong@gmail.com> Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Michal Marek <mmarek@suse.cz>
2011-02-25mac80211: make tx() operation return voidJohannes Berg
The return value of the tx operation is commonly misused by drivers, leading to errors. All drivers will drop frames if they fail to TX the frame, and they must also properly manage the queues (if they didn't, mac80211 would already warn). Removing the ability for drivers to return a BUSY value also allows significant cleanups of the TX TX handling code in mac80211. Note that this also fixes a bug in ath9k_htc, the old "return -1" there was wrong. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k] Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00] Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi] Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx] Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14zd1211rw: add unlikely to ZD_ASSERTJussi Kivilinna
Case assert is violated should be quite unlikely. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14zd1211rw: move async iowrite16v up to callersJussi Kivilinna
Writing beacon to device happen through multiple write command calls. zd_usb_iowrite16v uses synchronous urb call and with multiple write commands in row causes high CPU usage. Make asynchronous zd_usb_iowrite16v_async available outside zd_usb.c and use where possible. This lower CPU usage from ~10% to ~2% on Intel Atom when running AP-mode with 100 TU beacon interval. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14zd1211rw: use async urb for write commandJussi Kivilinna
Writing beacon to device happen through multiple write command calls. zd_usb_iowrite16v uses synchronous urb call and with multiple write commands in row causes high CPU usage. This patch makes zd_usb_iowrite16v use asynchronous urb submit within zd_usb.c. zd_usb_iowrite16v_async_start is used to initiate writing multiple commands to device using zd_usb_iowrite16v_async. Each URB is delayed and submitted to device by next zd_usb_iowrite16v_async call or by call to zd_usb_iowrite16v_async_end. URBs submitted by zd_usb_iowrite16v_async have URB_NO_INTERRUPT set and last URB send by zd_usb_iowrite16v_async_end does not. This lower CPU usage when doing writes that require multiple URBs. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14zd1211rw: correct use of usb_bulk_msg on interrupt endpointsJussi Kivilinna
zd1211rw is using usb_bulk_msg() with usb_sndbulkpipe() on interrupt endpoint. However usb_bulk_msg() internally corrects this and makes interrupt URB. It's better to change usb_bulk_msgs in zd1211rw to usb_interrupt_msg for less confusion. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: add useful debug outputJussi Kivilinna
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: enable NL80211_IFTYPE_APJussi Kivilinna
It should be safe to enable AP-mode now. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: reset rx urbs after idle period of 30 secondsJussi Kivilinna
RX appears to freeze while idle. Resetting rx-urbs appears to be enough to fix this. Do reset 30 seconds after last rx. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: reset device when CR_BCN_FIFO_SEMAPHORE freezes in beacon setupJussi Kivilinna
When driver fails to acquire device semaphore lock, device usually freezes soon afterwards. So failing to acquire lock indicates us that not everything is going right in device/fw. So reset device when this happens. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: add TX watchdog and device resettingJussi Kivilinna
When doing transfers at high speed for long time, tx queue can freeze. So add tx watchdog. TX-watchdog checks for locked tx-urbs and reset hardware when such is detected. Merely unlinking urb was not enough, device have to be reseted. Hw settings are restored so that any open link will stay on after reset. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: collect driver settings and add function to restore theimJussi Kivilinna
We need HW hard reset later in patchset to reset device after TX-stall. Collect all settings that we have set to driver for later reset and add restore function. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: lower hw command timeoutsJussi Kivilinna
Device command timeouts are set up very high (1 sec) and this causes AP beacon to lock up for long for example. Checking timeouts on device it's easy to see that 1 sec timeout is not needed, when device fails to response longer timeout doesn't help: [ 473.074419] zd1211rw 1-1:1.0: print_times() Read times: [ 473.175163] zd1211rw 1-1:1.0: print_time() 0 - 10 msec: 1506 [ 473.176429] zd1211rw 1-1:1.0: print_time() 11 - 50 msec: 0 [ 473.177955] zd1211rw 1-1:1.0: print_time() 51 - 100 msec: 0 [ 473.180703] zd1211rw 1-1:1.0: print_time() 101 - 250 msec: 0 [ 473.182101] zd1211rw 1-1:1.0: print_time() 251 - 500 msec: 0 [ 473.183221] zd1211rw 1-1:1.0: print_time() 500 - 1000 msec: 20 [ 473.184381] zd1211rw 1-1:1.0: print_time() 1000 - ... msec: 18 Also vendor driver doesn't use this long timeout. Therefore change timeout to 50msec. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: change interrupt URB buffer to DMA bufferJussi Kivilinna
As might lower beacon update CPU usage. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04zd1211rw: use stack and preallocated memory for small cmd-buffersJussi Kivilinna
Use stack for allocing small < 64 byte arrays in zd_chip.c and preallocated buffer in zd_usb.c. This might lower CPU usage for beacon setup. v2: - Do not use stack buffers in zd_usb.c as they would be used for urb transfer_buffer. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>