summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless
AgeCommit message (Collapse)Author
2012-02-27wireless: Fix typo in mac80211_hwsim.cMasanari Iida
Correct spelling "occured" to "occurred" in drivers/net/wireless/mac80211_hwsim.c Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27rt2x00:Add RT5372 chipset supportJohn Li
Signed-off-by: John Li <chen-yang.li@mediatek.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27ath9k: avoid useless cast from (struct ath_rateset *) to (u8 *) and backPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27rtlwifi: Fix breakage in debug functions when built as a moduleLarry Finger
Since commit 481b9606, it has not been possible to invoke debugging with any rtlwifi driver built as a module. Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27rt2x00:Add VCO recalibrationJohn Li
Signed-off-by: John Li <chen-yang.li@mediatek.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27ath9k: Fix descriptor length for AR9462Sujith Manoharan
Change the descriptor length to 24 and explicitly set the control field 23 to zero. Not doing so would result in dropping of frames. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27ath9k: Fix programming SYNTH4 for AR9462Sujith Manoharan
The LONG_SHIFT_SELECT offset is different for AR9462 from the other chip families. Fix this. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27ath9k: Initialize NF values properlySujith Manoharan
Using AR_SREV_* macros for setting up the chip-specific NF values will make adding support for new chips hard. Use separate macros for each chip. Currently, AR9462 has the same value for all NF limits. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27ath9k: Remove unused initvalsSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27ath9k: Fix phyerr debug statisticsSujith Manoharan
Validate the phyerr value against the max. size of the statistics array properly. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27ath9k: Prettify recv debugfs file outputSujith Manoharan
Dumping the RSSI information in the middle of error statistics is a bit misleading. Move them to the end. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27ath9k: Add a debugfs file to display reset statisticsSujith Manoharan
Location: <debugfs_path>/ieee80211/phy#/ath9k/reset Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27ath9k: Merge wiphy and misc debugfs filesSujith Manoharan
This patch merges the 'wiphy' and 'misc' debugfs files and consolidates the information. Information about the current channel and other HT parameters can be obtained from both mac80211 and iw. Remove such redundant data. The reset statistics have been removed, they will be re-added in a subsequent patch (in a new debugfs file). Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27ath9k: Remove unnecessary variable initializationSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27ath9k_hw: remove duplicate initvalsFelix Fietkau
Comparing SHA1 checksums of the initval tables has shown that there are many tables that are 100% identical. iniBank{0,1,2,3,7} and iniBB_RfGain are shared by AR5416, AR913x, AR9160 iniBank6 is shared between AR5416 and AR9160 iniBank6TPC is shared between AR913x and AR9160 iniPcieSerdes is the same for all AR9002 based devices The CCK FIR coefficients are shared between AR9271 and AR9287 Getting rid of those duplicates saves about 7.5k uncompressed (on MIPS). For AR9003 and later there are some duplicates as well, but I've decided to leave them in for now, as the initvals for those chips are still actively maintained by QCA. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27rt2x00: Add support for D-Link DWA-127 to rt2800usb.Gertjan van Wingerde
This is an RT3070 based device. Cc: <stable@vger.kernel.org> Reported-by: Mikhail Kryshen <mikhail@kryshen.net> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27Merge branch 'wireless-next' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi
2012-02-22ath9k: remove unnecessary PS wrappersMohammed Shafi Shajakhan
ath_set_channel is called from ath9k_config which already has proper PS wrappers Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22ath9k: remove obsolete commentsMohammed Shafi Shajakhan
the corresponding code/logic was removed in "ath9k: rework power state handling" Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22ath5k:Remove __raw_read and __raw_writeJonathan Bither
By swithing from our __raw_read and __raw_write functions to ioread32 and iowrite32, benchmarks on my desk with iperf went from 11MBps to 18.1MBps using the AHB bus on an EnGenius ECB3500 running OpenWRT. Signed-off-by: Jonathan Bither <jonbither@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22cfg80211: restructure AP/GO mode APIJohannes Berg
The AP/GO mode API isn't very clearly defined, it has "set beacon" and "new beacon" etc. Modify the API to the following: * start AP -- all settings * change beacon -- new beacon data * stop AP -- stop AP mode operation This also reflects in the nl80211 API, rename the commands there correspondingly (but keep the old names for compatibility.) Overall, this makes it much clearer what's going on in the API. Kalle developed the ath6kl changes, I created the rest of the patch. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: remove il_is_rfkill_hwStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: s/il_txq_mem/il_free_txq_mem/gStanislaw Gruszka
Previous name was confusing. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: s/S_RF_KILL_HW/S_RFKILL/gStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: small queue initializations cleanupStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: enable only rfkill interrupt when rfkill switch is on during IFF_UPStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: small il4965_set_hw_ready cleanupStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: check correct il_poll_bit error valueStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: do not grab nic access if rfkillStanislaw Gruszka
If rfkill is on il_grab_nic_access() fail and we can not write to the various registers during stop procedure. Write to those registers unconditionally instead. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwleagcy: fix ident code damageStanislaw Gruszka
Using ident is not always good. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwleagcy: remove old commentsStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: improve mac operation debuggability a bitStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: get rid of tx/rx traffic logStanislaw Gruszka
The same data can be gathered using monitor mode. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: merge all ops structures into oneStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: merge il_lib_ops into il_opsStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: remove il_apm_opsStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: merge eeprom_ops into lib_opsStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: remove temp_opsStanislaw Gruszka
Remove unneeded structure and cleanup temperature calibration routines a bit. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: move debugfs_ops to il_privStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: gather all 4965 handlers in one placeStanislaw Gruszka
Handers belongs logically into 4965-mac.c file. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: regulatory_bands is not an opsStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: use writeb,writel,readl directlyStanislaw Gruszka
That change will save us some CPU cycles at run time. Having port-based I/O seems to be not possible for PCIe devices. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: cleanup/fix memory barriersStanislaw Gruszka
wmb(), rmb() are not needed when writel(), readl() are used as accessors for MMIO. We use them indirectly via iowrite32(), ioread32(). What is needed mmiowb(), for synchronizing writes coming from different CPUs on PCIe bridge (see in patch comments). This fortunately is not needed on x86, where mmiowb() is just defined as compiler barrier. As iwlegacy devices are most likely not used on anything other than x86, this is not so important fix. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: always check if got h/w access before writeStanislaw Gruszka
Before we write to the device register always check if _il_grap_nic_access() was successful. Change type return type _il_grap_nic_access() to bool, and add likely()/unlikely() statements. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22iwlegacy: dump stack when fail to gain access to the deviceStanislaw Gruszka
Print dump stack when the device is not responding. This should give some more clue about the reason of failure. Also change the message we print, since "MAC in deep sleep" is kinda confusing. On the way add unlikely(), as fail to gain NIC access is hmm ... unlikely. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22rtlwifi: rtl8192se firmware load can overflow target bufferTim Gardner
Define RTL8190_MAX_RAW_FIRMWARE_CODE_SIZE which represents the maximimum possible firmware file size. Use it in the definition of the buffer which receives the firmware file data. Set RTL8190_MAX_RAW_FIRMWARE_CODE_SIZE closer to the actual size of the firmware file, e.g., 90000 (down from hard coded 164000). The current size of rtlwifi/rtl8192sefw.bin is 88856. Set max_fw_size to RTL8190_MAX_RAW_FIRMWARE_CODE_SIZE for the size limit check. Fix the error case where max_fw_size is not cleared if the size limit check fails. Cc: Chaoming Li <chaoming_li@realsil.com.cn> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22brcm80211: fmac: make sdio firmware filename specificArend van Spriel
The sdio driver part uses firmware name brcmfmac.bin. With addition of usb this name is too generic. This patch renames the filename to brcmfmac-sdio.bin. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22brcm80211: fmac: add USB support for bcm43235/6/8 chipsetsArend van Spriel
This patch extends the use of the brcmfmac driver with support for chipsets with a USB host interface. The first chipsets supported are the bcm43235, bcm43236, and bcm43238 for which firmware has been submitted. This driver change has been successfully built for x86, x86_64, ppc64, arm_le, and mips_be. It has been tested successfully on x86 and x86_64. Cc: M. Lambert <lambertm@westman.wave.ca> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Kan Yan <kanyan@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22brcm80211: fmac: use spinlock calls saving irq flags in brcmf_enq_event()Arend van Spriel
This function is executed within irq context. The call spin_unlock_irq does enable interrupts which is not desired in the irq context. This patch replaces them using the spin_loc_irqsave and spin_unlock_irqrestore functions. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Kan Yan <kanyan@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-22brcm80211: fmac: change allocation flag in brcmf_enq_event() functionArend van Spriel
As the function is called from atomic context it should not do the kzalloc call with GFP_KERNEL. Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Kan Yan <kanyan@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-10-19 17:38:24 +0000