summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless
AgeCommit message (Collapse)Author
2009-01-29wireless: restrict to 32 legacy ratesJohannes Berg
Since the standards only define 12 legacy rates, 32 is certainly a sane upper limit and we don't need to use u64 everywhere. Add sanity checking that no more than 32 rates are registered and change the variables to u32 throughout. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: Remove unnecessary gpio configuration in ath9k_hw_reset()Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: Fix typo in chip version checkVasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29mac80211: constify ieee80211_if_conf.bssidJohannes Berg
Then one place can be a static const. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwl3945: fix deep sleep when removing the driver.Abbas, Mohamed
A warning message "MAC is in deep sleep" sometimes happen when user removes the driver. This warning is related to card not being ready. In __iwl3945_down function some of the going down steps are in wrong order, to fix this this patch do the following: 1- make sure we are calling iwl3945_apm_reset and iwl3945_apm_stop in the right order. 2- make sure we set CSR_GP_CNTRL_REG_FLAG_INIT_DONE in apm_reset before poll on CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY. 3- set correct polling counter. This fixes bug http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1834 Signed-off-by: mohamed abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwl3945: Use iwl-rfkillSamuel Ortiz
Here again, the rfkill routines are duplicated between agn and 3945. Let's move the agn one to iwlcore, and so we can get rid of the 3945 ones. Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlagn: fix agn rate scalingAbbas, Mohamed
Sometime Tx reply rate different than what rate scale expecting causing rate scale to bail out. This could cause failing to commit LQ cmd. This patch will try to solve this instead of just bail out. It also make sure we start with a valid rate. Signed-off-by: mohamed abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: allow user to set max rateAbbas, Mohamed
allow user to set max rate through #iwconfig <inteface> rate XXX. mac80211 will try to force this if user set it, but driver is not in sync which cause mac80211 to report wrong current rate. This patch will check if max rate is set and force it in rate scaling Signed-off-by: mohamed abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: Enable dynamic power save in ath9k.Vivek Natarajan
This patch implements dynamic power save feature for ath9k. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: add recognition of Intel WiFi Link 100 SeriesJay Sternberg
add configuration for new Intel WiFi Link 100 series as part of the iwlagn driver under the umbrella of 5000 family of devices. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: add recognition of Intel WiFi Link 6000 and 6050 SeriesJay Sternberg
add configuration for new Intel WiFi Link Series as part of the iwlagn driver under the umbrella of 5000 family of devices. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: remove static from 5000 structuresJay Sternberg
remove static from config structures which will be used by new hardware that is similar to 5000. This way the new devices can use them without the new structures having to be stored in the already overloaded iwl-5000.c file. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: correct Kconfig to prevent following entries from not indentingJay Sternberg
defining configurations that are not visible caused the following entries to not be indented. changing the tree structure to name the top level selection and have all others reference IWLWIFI directly corrects this issue. Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: eliminate power_data_39.Winkler, Tomas
This patch eliminates 3945 power_data structure and make use of of iwl_power_data. Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: remove unused or twice defined members in iwl_privWinkler, Tomas
This patch removes user_txpower_limit and max_channel_txpower_limit and use tx_power_user_lmt and tx_power_channel_lmt instead call_post_assoc_from_beacon is not used Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: kill scan39Winkler, Tomas
scan and scan39 can be represented by void * in iwl_priv Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwl3945: Use iwl-hcmd host command routinesSamuel Ortiz
With the previously added tfd related ops, we can now use the iwl-tx.c host command enqueue routine. Since the 3945 host command specific routines are identical to the agn ones, we can just remove them from the 3945 code. Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: Add TFD library operationsSamuel Ortiz
The TFD structures for 3945 and agn HWs are fundamentally different. We thus need to define operations for attaching and freeing them. This will allow us to share a fair amount of code (cmd and tx queue related) between both drivers. Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwl3945: Use iwl_txq_update_write_ptrSamuel Ortiz
The iwl3945 and the iwl versions are identical. Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwl3945: add debugging for wrong command queueChatre, Reinette
We encountered a problem related to this BUG and need to obtain more debugging information. See bug report at http://marc.info/?l=linux-wireless&m=123147215829854&w=2 Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: kill iwl3945_scan_cancel and iwl3945_scan_cancel_timeoutWinkler, Tomas
This patch removes iwl3945_scan_cancel and iwl3945_scan_cancel_timeout because iwl_scan_cancel iwl_scan_cancel_timeout are just same. Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: fix iwl_mac_set_key and iwl3945_mac_set_keyWinkler, Tomas
This patch fix iwl_mac_set_key function changed in patch "mac80211: clean up set_key callback" 1. removing 'static' const u8 *addr' that can possible cause conflict when two or more NICs are present in the system. 2. simplifying functions Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlwifi: make iwl-power.c more readableWinkler, Tomas
This patch rearrange code in iwl-power.c function to make it a little more readable. No functional changes. Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: remove stop/start calls from within suspend/resumeBob Copeland
mac80211 now takes down interfaces automatically during suspend so doing it in the driver is unnecessary. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwlagn: fix hw-rfkill while the interface is downHelmut Schaa
Currently iwlagn is not able to report hw-killswitch events while the interface is down. This has implications on user space tools (like NetworkManager) relying on rfkill notifications to bring the interface up once the wireless gets enabled through a hw killswitch. Thus, enable the device already in iwl_pci_probe instead of iwl_up and enable interrups while the interface is down in order to get notified about killswitch state changes. The firmware loading is still done in iwl_up. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29iwl3945: fix some warnings when compiled without debugHelmut Schaa
Fix the following warnings if compiled without CONFIG_IWLWIFI_DEBUG. drivers/net/wireless/iwlwifi/iwl3945-base.c: In function ‘iwl3945_rx_reply_add_sta’: drivers/net/wireless/iwlwifi/iwl3945-base.c:2748: warning: unused variable ‘pkt’ drivers/net/wireless/iwlwifi/iwl3945-base.c: In function ‘iwl3945_rx_scan_results_notif’: drivers/net/wireless/iwlwifi/iwl3945-base.c:2903: warning: unused variable ‘notif’ drivers/net/wireless/iwlwifi/iwl3945-base.c: In function ‘iwl3945_rx_scan_complete_notif’: drivers/net/wireless/iwlwifi/iwl3945-base.c:2928: warning: unused variable ‘scan_notif’ Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: notice a negative keytypeRoel Kluin
To notice a negative keytype Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29rt2x00: Add LED_MODE_ASUS supportIvo van Doorn
When the led mode is asus, the activity led mode must be registered otherwise the second LED will not be enabled. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29rt2x00: conf_tx() only need register access for WMM queuesIvo van Doorn
conf_tx() in rt61pci and rt73usb only have to check once if the queue_idx indicates a non-WMM queue and break of the function immediately if that is the case. Only the WMM queues need to have the TX configuration written to the registers. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29rt2x00: Update copyright year to 2009Ivo van Doorn
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29Move orinoco Kconfig entries into drivers/net/wireless/orinoco/KconfigAndrey Borzenkov
Since driver now lives in separate subdirectory, move Kconfig entries in own file so they can be tweaked indepndently. It complements "orinoco: Move sources to a subdirectory". Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru> Acked-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29p54spi: remove arch specific dependenciesChristian Lamparter
On Friday 16 January 2009 20:33:43 Kalle Valo wrote: > N800 and N810 support is not on mainline yet, for stlc45xx I decided > to add module parameters for the gpio numbers. Here's the commit from > stlc45xx repo: > > http://gitorious.org/projects/stlc45xx/repos/mainline/commits/35afc5df0027d02d49e6f5bf986dcc4deb4ee6cf This is the same patch for p54spi. It removes all N800/N810 specific code from p54spi, so the driver can be used on other architectures, or configurations as well. Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29p54usb: fix conflict with recent usb changesChristian Lamparter
A recent change in the usb core "USB: change interface to usb_lock_device_for_reset()" conflicts with "p54usb: utilize usb_reset_device for 3887". Sadly, we have to call usb_reset_device before we can upload the firmware on 3887. Unless someone figures out how to reliably stop the 3887 so the hardware is still usable next time we want to start it. Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: Cleanup buffer type assignmentSujith
The buffer state is already cleared in ATH_TXBUF_RESET. Remove redundant code clearing the type variable. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: Revamp TX aggregationSujith
This patch cleans up the convoluted buffer management logic for TX aggregation. Both aggregation creation and completion are addressed. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: Handle holding descriptor in TX completion properlySujith
If the current holding descriptor is the last one in the TX queue, *and* it has been marked as STALE, then move it to the free list and bail out, as it has already been processed. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: Add a helper function to wake mac80211 queuesSujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: Merge queue draining functionsSujith
The TX queue draining routines have confusing names, rename them approprately and merge ath_drain_txdataq() with ath_drain_all_txq(). Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: Remove ath_tx_stopdma and call ath9k_hw_stoptxdma directlySujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: Reorganize code in xmit.cSujith
This patch starts cleaning up all the crufty code in transmission path, grouping functions into logical blocks. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: Update short guard interval in rate controlSujith
The rate control algorithm needs to know if a STA allows short guard interval, fixing this allows RC to use the correct table. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: rateCodeToIndex is not used, remove itSujith
Calculation of rate indices from ratecode is done in recv.c in a straightforward manner for both HT and legacy rates. This variable is not needed anymore. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: enable support for AR9100Gabor Juhos
Because we have support for the AR9100 devices now, we can enable them. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: fix null pointer dereference in ani monitor codeGabor Juhos
In 'ath9k_ani_reset' the 'ahp->ah_curani' will be initialized only if 'DO_ANI(ah)' true. In 'ath9k_hw_ani_monitor' we are using 'ahp->ah_curani' unconditionally, and it will cause a NULL pointer dereference on AR9100. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: fix ar5416Addac_9100 valuesGabor Juhos
Writing the register at offset 0x98c4 causes a deadlock on the AR913x SoCs. Although i don't have detailed knowledge about these registers, but if i change the register offset according to the 'ar5416Addac' table, it works. Additionally there is no reference to the 0x98c4 elsewhere. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: remove (u16) casts from rtc register accessGabor Juhos
The RTC register offsets don't fit into 'u16' on the AR913x, so we have to remove the existing casts. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: get EEPROM contents from platform data on AHB busGabor Juhos
On the AR913x SOCs we have to provide EEPROM contents via platform_data, because accessing the flash via MMIO is not safe. Additionally different boards may store the radio calibration data at different locations. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: introduce platform driver for AHB bus supportGabor Juhos
This patch adds the platform_driver itself, and modifies the main driver to register it. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: move PCI code into separate fileGabor Juhos
Now that we have converted all bus specific routines to replaceable, we can move the PCI specific codes into a separate file. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath9k: introduce bus specific cleanup routineGabor Juhos
We have left only some PCI specific cleanup code. We have to convert them as well. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-21 13:53:48 +0000