| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) close should do napi_disable() not napi_enable
2) remove unused local var 'todo'
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->truesize was not being incremented at all to
reflect the page based data added to RX SKBs.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts changeset fa4f0774d7c6cccb4d1fda76b91dd8eddcb2dd6a
([CASSINI]: dont touch page_count) because it breaks the driver.
The local page counting added by this changeset did not account
for the asynchronous page count changes done by kfree_skb()
and friends.
The change adds extra atomics and on top of it all appears to be
totally unnecessary as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Nick Piggin <npiggin@suse.de>
|
|
Here's proposed fix for RX checksum handling in cassini; it affects
little-endian working with half-duplex gigabit, but obviously needs
testing on big-endian too.
The problem is, we need to convert checksum to fixed-endian *before*
correcting for (unstripped) FCS. On big-endian it won't matter
(conversion is no-op), on little-endian it will, but only if FCS is
not stripped by hardware; i.e. in half-duplex gigabit mode when
->crc_size is set.
cassini.c part is that fix, cassini.h one consists of trivial
endianness annotations. With that applied the sucker is endian-clean,
according to sparse.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move veth.h from net/ to linux/ since it is a user api, and add it to
user header processing Kbuild.
[ Use header-y as suggested by Sam Ravnborg. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a trivial fix of debug message.
When a persist flag is set, the message should say "enabled".
Signed-off-by: Toyo Abe <tabe@miraclelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initially transmit buffer pointers were only reset. But buffer
descriptors were possibly still set as ready, and buffer in upper
layer was not freed. This caused driver hang under big load. Now
reset clean properly the buffer descriptor and freed upper layer.
Signed-off-by: Gregory CLEMENT <gclement00@gmail.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes
|
|
Same story as with olympic - htons(readw()) when swab16(readw()) is needed,
missing conversions to le32 when dealing with shared descriptors, etc.
Olympic got those fixes in 2.4.0-test2, 3c359 didn't.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
If you need to find a difference between addresses of two
struct members, subtract offsetof() or cast addresses to
char * and subtract those if you prefer it that way. Doing
that same with s/char */u32/, OTOH...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Both store MAC address in CIS; there's no decoder for that
type (0x88) so the drivers work with raw data. It is
byteswapped, so ntohs() works for little-endian, but for
big-endian it's wrong. ntohs(le16_to_cpu()) does the
right thing on both (and always expands to swab16()).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
missing conversions in a couple of places
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* shift before cpu_to_le64(), not after it
* writel() converts to l-e itself
* misc missing conversions
* in set_multicast() hash_table[] is host-endian; we feed it to card
via writel() and populate it as host-endian, so we'd better put the
first element into it also in host-endian
* pci_unmap_single() et.al. expect host-endian, not little-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
pci_unmap_single() and friends getting a little-endian address...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* usb_control_message() to/from stack (breaks on e.g. arm); some
places did kmalloc() for buffer, some just worked from stack.
Added kmalloc()/memcpy()/kfree() in asix_read_cmd()/asix_write_cmd(),
removed that crap from callers.
* Fixed a leak in ax88172_bind() - on success it forgot to kfree() the
buffer.
* Endianness bug in ax88178_bind() - we read a word from eeprom and work with
it without converting to host-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
skb->protocol is net-endian, TYVM...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
txlo_dma_addr should be host-endian; we pass it to typhoon_tso_fill(),
which does arithmetics on it, converts to l-e and passes it to card.
Unfortunately, we forgot le32_to_cpu() when initializing it from
face->txLoAddr, which sits in shared memory and is little-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
rxBuffCleared is little-endian; we miss le32_to_cpu() in checks for
rx ring overruns.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
One cpu_to_le16() too many when passing argument for TYPHOON_CMD_XCVR_SELECT;
we end up passing host-endian while the hardware expects little-endian. The
other place doing that (typhoon_start_runtime()) does the right thing, so the
card will recover at the next ifconfig up/tx timeout/resume, which limits the
amount of mess, but still, WTF?
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
in typhoon_get_drvinfo() .parm2 is little-endian; not critical
since we just get the firmware id flipped in get_drvinfo output
on big-endian boxen, but...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
txBytes and rxBytesGood are both 64bit; using le32_to_cpu() won't work
on big-endian for obvious reasons.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
if log_len is larger than 4K then we are killing the stack.
allocate on heap instead and limit size to what practically can
be used (PAGE_SIZE)
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch moves _cancel_deferred_work out of mutex protection and removes
unnecessary mutex in pci_suspend and pci_resume.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some people would like to know what p54 is.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Thanks to Matthias Mueller for reporting this device.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
tg3_nvram_write_block_unbuffered() is reading data from nvram into
allocated buffer before overwriting a part of it with user-supplied
data. Then it feeds the entire page back to nvram. It should be
storing the words it had read as little-endian, not as host-endian.
Note that tg3_set_eeprom() does exactly that for padding the same
data to full words before it gets passed down to tg3_nvram_write_block()
and then to tg3_nvram_write_block_unbuffered().
Moreover, when we get to sending the entire thing back to nvram, we
go through it word-by-word, doing essentially
writel(swab32(le32_to_cpu(word)), ...)
so if we want them to reach the card in host-independent endianness,
we'd better really have all that buffer filled with fixed-endian.
For user-supplied part we obviously do have that (it's an array of
octets memcpy'd in), ditto for padding of user-supplied part to word
boundaries (taken care of in tg3_set_eeprom()). The rest of the
buffer gets filled by tg3_nvram_write_block_unbuffered() and it would
damn better be consistent with that (and with tg3_get_eeprom(), while
we are at it - there we also convert the words read from nvram to
little-endian before returning the buffer to user).
The bug should get triggered on big-endian boxen when set_eeprom is done
for less than entire page. Then the words that should've been unaffected
at all will actually get byteswapped in place in nvram.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed misannotations, introduced a new helper - tg3_nvram_read_le().
It gets __le32 * instead of u32 * and puts there the value converted
to little-endian. A lot of callers of tg3_nvram_read() were doing
that; converted them to tg3_nvram_read_le().
At that point the driver is practically endian-clean; the only remaining
place is an actual bug, AFAICS; will be dealt with in the next patch.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (23 commits)
iwlwifi: fix rf_kill state inconsistent during suspend and resume
b43: Fix rfkill radio LED
bcm43xx_debugfs sscanf fix
libertas: select WIRELESS_EXT
iwlwifi3945/4965: fix rate control algo reference leak
ieee80211_rate: missed unlock
wireless/ipw2200.c: add __dev{init,exit} annotations
zd1211rw: Fix alignment problems
libertas: add Dan Williams as maintainer
sis190 endianness
ucc_geth: really fix section mismatch
pcnet_cs: add new id
ixgb: make sure jumbos stay enabled after reset
Net: ibm_newemac, remove SPIN_LOCK_UNLOCKED
net: smc911x: shut up compiler warnings
ucc_geth: minor whitespace fix
drivers/net/s2io.c section fixes
drivers/net/sis190.c section fix
hamachi endianness fixes
e100: free IRQ to remove warningwhenrebooting
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes
|
|
The patch fixes the STATUS_RF_KILL_HW state is not cleared problem if the
device goes to suspend when the rf_kill switch is enabled. The bug causes
the driver always thinks the rf_kill switch is enabled (although it is
disabled) after resume.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes Bug #9414
Since addition of the rfkill callback, the LED associated with the off
switch on the radio has not worked for several reasons:
(1) Essential data in the rfkill structure were missing.
(2) The rfkill structure was initialized after the LED initialization.
(3) There was a minor memory leak if the radio LED structure was inited.
Once the above problems were fixed, additional difficulties were noted:
(4) The radio LED was in the wrong state at startup.
(5) The radio switch had to be manipulated twice for each state change.
(6) A circular mutex locking situation existed.
(7) If rfkill-input is built as a module, it is not automatically loaded.
This patch fixes all of the above.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ia64:
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c: In function `tsf_write_file':
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:237: warning: long long int format, u64 arg (arg 3)
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:237: warning: long long int format, u64 arg (arg 3)
We do not know what type was used to implement u64 and we can never use u64 in
printk(), sscanf(), etc.
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Ensure that libertas selects WIRELESS_EXT, since selecting other stuff that
should depend on WEXT, like IEEE80211, doesn't seem to drag that in for us.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix rate control algo reference leak in case if network device has been
failed to register. In this case special flag priv->mac80211_registered is
not set and the rate algo reference is not freeing on module unload. That
leads to OOPs in further ieee80211 rate register/unregister procedure (by
any callee).
It should fix the bug #9470
http://bugzilla.kernel.org/show_bug.cgi?id=9470
[akpm@linux-foundation.org: build fix]
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds __dev{init,exit} annotations.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Shaddy Baddah found an alignment problem with zd1211rw driver at
2007-11-19. This patch fixes it, it is based on the patch proposed by
Herbert Xu. The alignment 4 has been the agreed value on the
linux-wireless mailing list.
Notify that the problem does only affect the old zd1211rw softmac
driver and not the zd1211rw-mac80211 driver. Daniel Drake has
already provided a patch for the replacement of the softmac
driver, which this patch will break.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Check in sis190_rx_interrupt() is broken on big-endian
(desc->status is little-endian and everything else actually uses
it correctly, including other checks for OWNbit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Commit ed7e63a51d46e835422d89c687b8a3e419a4212a has tried to fix
section mismatch:
WARNING: vmlinux.o(.init.text+0x17278): Section mismatch: reference to
.exit.text:uec_mdio_exit (between 'ucc_geth_init' and 'uec_mdio_init')
But that mismatch still happens.
This patch actually fixing section mismatch by removing __exit from
the header file.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
add new id: Planex CF-10T
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[IRDA]: irda parameters warning fixes.
[IRDA]: stir4200 fixes.
[IRDA]: irlmp_unregister_link() needs to free lsaps.
[IRDA]: mcs7780 needs to free allocated rx buffer.
[IRDA]: Race between open and disconnect in irda-usb.
[SCTP]: Flush fragment queue when exiting partial delivery.
[AX25]: Locking dependencies fix in ax25_disconnect().
[IPV4]: Make tcp_input_metrics() get minimum RTO via tcp_rto_min()
[IPV6]: Fix the return value of ipv6_getsockopt
[BRIDGE]: Assign random address.
[IPV4]: Updates to nfsroot documentation
[ATM]: Fix compiler warning noise with FORE200E driver
[NETFILTER]: bridge: fix missing link layer headers on outgoing routed packets
[SYNCPPP]: Endianness and 64bit fixes.
[TIPC]: Fix semaphore handling.
[NETFILTER]: xt_hashlimit should use time_after_eq()
[XFRM]: Display the audited SPI value in host byte order.
[NETFILTER]: ip_tables: fix compat copy race
[NETFILTER]: ctnetlink: set expected bit for related conntracks
|
|
From: Olaf Hartmann <olaf.hartmann@s1998.tu-chemnitz.de>
The attached patch observes the stir4200 fifo size and will clear the
fifo, if the size is increasing, while it should be transmitting bytes
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While testing the mcs7780 based IrDA USB dongle I've stumbled upon
memory leak in mcs_net_close(). Patch below fixes it.
Signed-off-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems to me that irda_usb_net_open() must set self->netopen
under spinlock or disconnect() may fail to kill all URBs, if it is called
while an interface is opened.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* trivial annotations
* long != 32bit, use __be32
* wrong endianness in sending CISCO_ADDR_REPLY
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently a device reset (ethtool -r ethX) would cause the
adapter to fall back to regular MTU sizes.
Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
SPIN_LOCK_UNLOCKED is deprecated, use DEFINE_SPINLOCK instead
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
