| Age | Commit message (Collapse) | Author |
|---|
|
After pcmcia_request_io(), do not make use of the values stored in
io_req_t, but instead use those found in struct pcmcia_device->resource[].
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Use pcmcia_read_config_byte and pcmcia_write_config_byte instead
of pcmcia_access_configuration_register.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Remove cs_types.h which is no longer needed: Most definitions aren't
used at all, a few can be made away with, and two remaining definitions
(typedefs, unfortunatley) may be moved to more specific places.
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
bridge: Partially disable netpoll support
tcp: fix crash in tcp_xmit_retransmit_queue
IPv6: fix CoA check in RH2 input handler (mip6_rthdr_input())
ibmveth: lost IRQ while closing/opening device leads to service loss
rt2x00: Fix lockdep warning in rt2x00lib_probe_dev()
vhost: avoid pr_err on condition guest can trigger
ipmr: Don't leak memory if fib lookup fails.
vhost-net: avoid flush under lock
net: fix problem in reading sock TX queue
net/core: neighbour update Oops
net: skb_tx_hash() fix relative to skb_orphan_try()
rfs: call sock_rps_record_flow() in tcp_splice_read()
xfrm: do not assume that template resolving always returns xfrms
hostap_pci: set dev->base_addr during probe
axnet_cs: use spin_lock_irqsave in ax_interrupt
dsa: Fix Kconfig dependencies.
act_nat: not all of the ICMP packets need an IP header payload
r8169: incorrect identifier for a 8168dp
Phonet: fix skb leak in pipe endpoint accept()
Bluetooth: Update sec_level/auth_type for already existing connections
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
The order of freeing the IRQ and freeing the device in firmware
in ibmveth_close can cause the adapter to become unusable after a
subsequent ibmveth_open. Only a reboot of the OS will make the
network device usable again. This is seen when cycling the adapter
up and down while there is network activity.
There is a window where an IRQ will be left unserviced (H_EOI will not
be called). The solution is to make a VIO_IRQ_DISABLE h_call, free the
device with firmware, and then call free_irq.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rt2x00dev->intf_work workqueue is never initialized when a driver is
probed for a non-existent device (in this case rt2500usb). On such a
path we call rt2x00lib_remove_dev() to free any resources initialized
during the probe before we use INIT_WORK to initialize the workqueue.
This causes lockdep to get confused since the lock used in the workqueue
hasn't been initialized yet but is now being acquired during
cancel_work_sync() called by rt2x00lib_remove_dev().
Fix this by initializing the workqueue first before we attempt to probe
the device. This should make lockdep happy and avoid breaking any
assumptions about how the library cleans up after a probe fails.
phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2027, comm: modprobe Not tainted 2.6.35-rc5+ #60
Call Trace:
[<ffffffff8105fe59>] register_lock_class+0x152/0x31f
[<ffffffff81344a00>] ? usb_control_msg+0xd5/0x111
[<ffffffff81061bde>] __lock_acquire+0xce/0xcf4
[<ffffffff8105f6fd>] ? trace_hardirqs_off+0xd/0xf
[<ffffffff81492aef>] ? _raw_spin_unlock_irqrestore+0x33/0x41
[<ffffffff810628d5>] lock_acquire+0xd1/0xf7
[<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
[<ffffffff8104f06e>] __cancel_work_timer+0xd0/0x17e
[<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
[<ffffffff8104f136>] cancel_work_sync+0xb/0xd
[<ffffffffa0096675>] rt2x00lib_remove_dev+0x25/0xb0 [rt2x00lib]
[<ffffffffa0096bf7>] rt2x00lib_probe_dev+0x380/0x3ed [rt2x00lib]
[<ffffffff811d78a7>] ? __raw_spin_lock_init+0x31/0x52
[<ffffffffa00bbd2c>] ? T.676+0xe/0x10 [rt2x00usb]
[<ffffffffa00bbe4f>] rt2x00usb_probe+0x121/0x15e [rt2x00usb]
[<ffffffff813468bd>] usb_probe_interface+0x151/0x19e
[<ffffffff812ea08e>] driver_probe_device+0xa7/0x136
[<ffffffff812ea167>] __driver_attach+0x4a/0x66
[<ffffffff812ea11d>] ? __driver_attach+0x0/0x66
[<ffffffff812e96ca>] bus_for_each_dev+0x54/0x89
[<ffffffff812e9efd>] driver_attach+0x19/0x1b
[<ffffffff812e9b64>] bus_add_driver+0xb4/0x204
[<ffffffff812ea41b>] driver_register+0x98/0x109
[<ffffffff813465dd>] usb_register_driver+0xb2/0x173
[<ffffffffa00ca000>] ? rt2500usb_init+0x0/0x20 [rt2500usb]
[<ffffffffa00ca01e>] rt2500usb_init+0x1e/0x20 [rt2500usb]
[<ffffffff81000203>] do_one_initcall+0x6d/0x17a
[<ffffffff8106cae8>] sys_init_module+0x9c/0x1e0
[<ffffffff8100296b>] system_call_fastpath+0x16/0x1b
Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
"hostap: Protect against initialization interrupt" (which reinstated
"wireless: hostap, fix oops due to early probing interrupt")
reintroduced Bug 16111. This is because hostap_pci wasn't setting
dev->base_addr, which is now checked in prism2_interrupt. As a result,
initialization was failing for PCI-based hostap devices. This corrects
that oversight.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use spin_lock_irqsave instead of spin_lock in ax_interrupt because
the interrupt handler can also be invoked from ei_watchdog.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Merge error.
See CFG_METHOD_8 (0x3c800000 + 0x00300000) since version 8.002.00
of Realtek's driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (35 commits)
NET: SB1250: Initialize .owner
vxge: show startup message with KERN_INFO
ll_temac: Fix missing iounmaps
bridge: Clear IPCB before possible entry into IP stack
bridge br_multicast: BUG: unable to handle kernel NULL pointer dereference
net: Fix definition of netif_vdbg() when VERBOSE_DEBUG is defined
net/ne: fix memory leak in ne_drv_probe()
xfrm: fix xfrm by MARK logic
virtio_net: fix oom handling on tx
virtio_net: do not reschedule rx refill forever
s2io: resolve statistics issues
linux/net.h: fix kernel-doc warnings
net: decreasing real_num_tx_queues needs to flush qdisc
sched: qdisc_reset_all_tx is calling qdisc_reset without qdisc_lock
qlge: fix a eeh handler to not add a pending timer
qlge: Replacing add_timer() to mod_timer()
usbnet: Set parent device early for netdev_printk()
net: Revert "rndis_host: Poll status channel before control channel"
netfilter: ip6t_REJECT: fix a dst leak in ipv6 REJECT
drivers: bluetooth: bluecard_cs.c: Fixed include error, changed to linux/io.h
...
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/sb1250-mac.c | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original KERN_CRIT will mess up terminals.
CC: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix missing iounmaps.
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Failure cases within ath9k_hif_usb_alloc_urbs are failed
to release allocated memory.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
net_device allocated with alloc_eip_netdev() must be freed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
virtio net will never try to overflow the TX ring, so the only reason
add_buf may fail is out of memory. Thus, we can not stop the
device until some request completes - there's no guarantee anything
at all is outstanding.
Make the error message clearer as well: error here does not
indicate queue full.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (...and avoid TX_BUSY)
Cc: stable@kernel.org # .34.x (s/virtqueue_/vi->svq->vq_ops->/)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently fill all of RX ring, then add_buf
returns ENOSPC, which gets mis-detected as an out of
memory condition and causes us to reschedule the work,
and so on forever. Fix this by oom = err == -ENOMEM;
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .34.x
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch resolves a number of issues in the statistics gathering of
the s2io driver.
On Xframe adapters, the received multicast statistics counter includes
pause frames which are not indicated to the driver. This can cause
issues where the multicast packet count is higher than what has actually
been received, possibly higher than the number of packets received.
The driver software counters are replaced with the adapter hardware
statistics for rx_packets, rx_bytes, and tx_bytes. It also uses the
overflow registers to determine if the statistics wrapped the 32bit
register (removing the window of having a statistic value less than the
previous call). rx_length_errors statistic now includes undersized
packets in addition to oversized packets in its counting. Finally,
rx_crc_errors are now being counted.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reducing real_num_queues needs to flush the qdisc otherwise
skbs with queue_mappings greater then real_num_tx_queues can
be sent to the underlying driver.
The flow for this is,
dev_queue_xmit()
dev_pick_tx()
skb_tx_hash() => hash using real_num_tx_queues
skb_set_queue_mapping()
...
qdisc_enqueue_root() => enqueue skb on txq from hash
...
dev->real_num_tx_queues -= n
...
sch_direct_xmit()
dev_hard_start_xmit()
ndo_start_xmit(skb,dev) => skb queue set with old hash
skbs are enqueued on the qdisc with skb->queue_mapping set
0 < queue_mappings < real_num_tx_queues. When the driver
decreases real_num_tx_queues skb's may be dequeued from the
qdisc with a queue_mapping greater then real_num_tx_queues.
This fixes a case in ixgbe where this was occurring with DCB
and FCoE. Because the driver is using queue_mapping to map
skbs to tx descriptor rings we can potentially map skbs to
rings that no longer exist.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some ocasions the function qlge_io_resume() tries to add a
pending timer, which causes the system to hit the BUG() on
add_timer() function.
This patch removes the timer during the EEH recovery.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently qlge driver calls add_timer() instead of mod_timer().
This patch changes add_timer() to mod_timer(), which seems a better
solution.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_printk() follows the net_device's parent device pointer, so
we must set that earlier than we previously did.
Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit c17b274dc2aa538b68c1f02b01a3c4e124b435ba.
That change was reported to break rndis_wlan support for the WUSB54GS.
Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When there is a firmware error or the firmware is reloaded for some other
reason we currently clear all station information, including keys
associated with them. A problem is that we do not clear some other
information regarding keys that are not stored in the station structs.
The consequence of this is that when the device is reconfigured after the
firmware reload we can, among other things, run out of key indices.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16232
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2221
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
|
|
When two systems using bonding devices in adaptive load
balancing (ALB) communicates with each other, an endless
ping-pong of ARP replies starts between these two systems.
What happens? In the ALB mode, bonding driver keeps track
of each client connected in a hash table, so it can do the
receive load balancing (RLB). This hash table is updated
when an ARP reply is received, then it scans for the client
entry, updates its MAC address and flag it to be announced
later. Therefore, two seconds later, the alb monitor runs
and send for each updated client entry two ARP replies
updating this specific client. The same process happens on
the receiving system, causing the endless ping-pong of arp
replies.
See more information including the relevant functions below:
System 1 System 2
bond0 bond0
ping <system2>
ARP request --------->
<--------- ARP reply
+->rlb_arp_recv <---------------------+ <--- loop begins
| rlb_update_entry_from_arp |
| client_info->ntt = 1; |
| bond_info->rx_ntt = 1; |
| |
| <communication succeed> |
| |
| bond_alb_monitor |
| rlb_update_rx_clients |
| rlb_update_client |
| arp_create(ARPOP_REPLY) |
| send ARP reply --------------> V
| send ARP reply -------------->
| rlb_arp_recv
| rlb_update_entry_from_arp
| client_info->ntt = 1;
| bond_info->rx_ntt = 1;
| < snipped, same as in system 1>
+------- <-------------- send ARP reply
<-------------- send ARP reply
Besides the unneeded networking traffic, this loop breaks
a cluster because a backup system can't take over the IP
address. There is always one system sending an ARP reply
poisoning the network.
This patch fixes the problem adding a check for the MAC
address before updating it. Thus, if the MAC address didn't
change, there is no need to update neither to announce it later.
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some controllers (KW, Dove) limits the TX IP/layer4 checksum offloading to a max size.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
In driver ixgbe, ixgbe_atr may cause crashes for non-ipv4 packets. Just
add a test to check skb->protocol. It may crash on short packets due
to ip_hdr() access.
Signed-off-by: Guillaume Gaudonville <guillaume.gaudonville@6wind.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disabling the tx laser while receiving DMA requests
can hang the device. After this occurs the device
is in a bad state. The GPIO bit never clears when
PCI master access is disabled and a reboot is required
to get the device in a good state again.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added to 2.6.34:
commit 5f6c01819979afbfec7e0b15fe52371b8eed87e8
Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
Date: Wed Apr 14 16:04:23 2010 -0700
ixgbe: fix bug with vlan strip in promsic mode
among other things added a function called ixgbe_vlan_filter_enable.
This new function wants to access and set some rx_ring parameters, but
adapter->rx_ring has already been freed. This simply moves the free
until after the access and makes __ixgbe_shutdown look more like
ixgbe_remove.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support for netpoll over bonded interfaces was added here:
commit f6dc31a85cd46a959bdd987adad14c3b645e03c1
Author: WANG Cong <amwang@redhat.com>
Date: Thu May 6 00:48:51 2010 -0700
bonding: make bonding support netpoll
but it is bad enough that we should probably just disable netpoll over
bonding until some of the locking logic in the bonding driver is changed
or converted completely to RCU. Simple actions like changing the active
slave in active-backup mode will hang the box if a high enough printk
debugging level is enabled.
Keeping the old code around will be good for anyone that wants to work
on it (and for after the RCU conversion), so I propose this small patch
rather than ripping it all out.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
phylib: Add autoload support for the LXT973 phy.
ISDN: hysdn, fix potential NULL dereference
vxge: fix memory leak in vxge_alloc_msix() error path
isdn/gigaset: correct CAPI connection state storage
isdn/gigaset: encode HLC and BC together
isdn/gigaset: correct CAPI DATA_B3 Delivery Confirmation
isdn/gigaset: correct CAPI voice connection encoding
isdn/gigaset: honor CAPI application's buffer size request
cpmac: do not leak struct net_device on phy_connect errors
smc91c92_cs: fix the problem that lan & modem does not work simultaneously
ipv6: fix NULL reference in proxy neighbor discovery
Bluetooth: Bring back var 'i' increment
xfrm: check bundle policy existance before dereferencing it
sky2: enable rx/tx in sky2_phy_reinit()
cnic: Disable statistics initialization for eth clients that do not support statistics
net: add dependency on fw class module to qlcnic and netxen_nic
snmp: fix SNMP_ADD_STATS()
hso: remove setting of low_latency flag
udp: Fix bogus UFO packet generation
lasi82596: fix netdev_mc_count conversion
...
|
|
Commit e13647c1 (phylib: Add support for the LXT973 phy.) added a new ID
but neglected to also add it to the MODULE_DEVICE_TABLE.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When pci_enable_msix() returned ret<0, entries and vxge_entries were leaked.
While at it, use the centralized exit idiom in the function.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the call to phy_connect fails, we will return directly instead of freeing
the previously allocated struct net_device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smc91c92_cs:
Fix the problem that lan & modem does not work simultaneously
in the Megahertz multi-function card.
We need to write MEGAHERTZ_ISR to retrigger interrupt.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When building tx command, always set TX_CMD_FLAG_PROT_REQUIRE_MSK
for 5000 series and up.
Without setting this bit the firmware will not examine the RTS/CTS setting
and thus not send traffic with the appropriate protection. RTS/CTS is is
required for HT traffic in a noisy environment where, without this setting,
connections will stall on some hardware as documented in the patch that
initially attempted to address this:
commit 1152dcc28c66a74b5b3f1a3ede0aa6729bfd48e4
Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Date: Fri Jan 15 13:42:58 2010 -0800
iwlwifi: Fix throughput stall issue in HT mode for 5000
Similar to 6000 and 1000 series, RTS/CTS is the recommended
protection mechanism for 5000 series in HT mode based on the HW design.
Using RTS/CTS will better protect the inner exchange from interference,
especially in highly-congested environment, it also prevent uCode encounter
TX FIFO underrun and other HT mode related performance issues.
For 3945 and 4965, different flags are used for RTS/CTS or CTS-to-Self
protection.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
|
commit 3474ad635db371b0d8d0ee40086f15d223d5b6a4
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Apr 29 04:43:05 2010 -0700
iwlwifi: apply filter flags directly
broke multicast. The reason, it turns out, is that
the code previously checked if ALLMULTI _changed_,
which the new code no longer did, and normally it
_never_ changes. Had somebody changed it manually,
the code prior to my patch there would have been
broken already.
The reason is that we always, unconditionally, ask
the device to pass up all multicast frames, but the
new code made it depend on ALLMULTI which broke it
since now we'd pass up multicast frames depending
on the default filter in the device, which isn't
necessarily what we want (since we don't program it
right now).
Fix this by simply not checking allmulti as we have
allmulti behaviour enabled already anyway.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Tested-by: Brandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are few places where ANI is started without checking
if it is right to start. This might lead to a case where ani
timer would be left undeleted and cause improper memory acccess
during module unload. This bug is clearly exposed with
paprd support where the driver detects tx hang and does a
chip reset. During this reset ani is (re)started without checking
if it needs to be started. This would leave a timer scheduled
even after all the resources are freed and cause a panic.
This patch introduces a bit in sc_flags to indicate if ani
needs to be started in sw_scan_start() and ath_reset().
This would fix the following panic. This issue is easily seen
with ar9003 + paprd.
BUG: unable to handle kernel paging request at 0000000000003f38
[<ffffffff81075391>] ? __queue_work+0x41/0x50
[<ffffffff8106afaa>] run_timer_softirq+0x17a/0x370
[<ffffffff81088be8>] ? tick_dev_program_event+0x48/0x110
[<ffffffff81061f69>] __do_softirq+0xb9/0x1f0
[<ffffffff810ba060>] ? handle_IRQ_event+0x50/0x160
[<ffffffff8100af5c>] call_softirq+0x1c/0x30
[<ffffffff8100c9f5>] do_softirq+0x65/0xa0
[<ffffffff81061e25>] irq_exit+0x85/0x90
[<ffffffff8155e095>] do_IRQ+0x75/0xf0
[<ffffffff815570d3>] ret_from_intr+0x0/0x11
<EOI>
[<ffffffff812fd67b>] ? acpi_idle_enter_simple+0xe4/0x119
[<ffffffff812fd674>] ? acpi_idle_enter_simple+0xdd/0x119
[<ffffffff81441c87>] cpuidle_idle_call+0xa7/0x140
[<ffffffff81008da3>] cpu_idle+0xb3/0x110
[<ffffffff81550722>] start_secondary+0x1ee/0x1f5
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
statistics
Disable statistics initialization for eth clients that do not support
statistics. This prevents memory corruption on bnx2x hw.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
|
|
netxen_nic and qlcnic driver depends on firmware_class module.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
This patch removes the setting of the low_latency flag.
tty_flip_buffer_push() is occasionally being called in irq context, which
causes a hang if the low_latency flag is set.
Removing the low_latency flag only seems to impact the flush to ldisc,
which will now be put on a workqueue.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix commit 4cd24eaf0 (net: use netdev_mc_count and netdev_mc_empty when
appropriate)
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
$ make CONFIG_DEBUG_SECTION_MISMATCH=y
[...]
WARNING: drivers/net/built-in.o(.data+0x0): Section mismatch in reference from the variable mipsnet_driver to the function .init.text:mipsnet_probe()
The variable mipsnet_driver references
the function __init mipsnet_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
[...]
Fixed by making mipsnet_probe __devinit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/mipsnet.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ath5k assumes ah_current_channel is always a valid pointer in
several places, but a newly created interface may not have a
channel. To avoid null pointer dereferences, set it up to point
to the first available channel until later reconfigured.
This fixes the following oops:
$ rmmod ath5k
$ insmod ath5k
$ iw phy0 set distance 11000
BUG: unable to handle kernel NULL pointer dereference at 00000006
IP: [<d0a1ff24>] ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k]
*pde = 00000000
Oops: 0000 [#1]
last sysfs file: /sys/devices/pci0000:00/0000:00:0e.0/ieee80211/phy0/index
Modules linked in: usbhid option usb_storage usbserial usblp evdev lm90
scx200_acb i2c_algo_bit i2c_dev i2c_core via_rhine ohci_hcd ne2k_pci
8390 leds_alix2 xt_IMQ imq nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_cc
Pid: 1597, comm: iw Not tainted (2.6.32.14 #8)
EIP: 0060:[<d0a1ff24>] EFLAGS: 00010296 CPU: 0
EIP is at ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k]
EAX: 000000c2 EBX: 00000000 ECX: ffffffff EDX: c12d2080
ESI: 00000019 EDI: cf8c0000 EBP: d0a30edc ESP: cfa09bf4
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
Process iw (pid: 1597, ti=cfa09000 task=cf88a000 task.ti=cfa09000)
Stack:
d0a34f35 d0a353f8 d0a30edc 000000fe cf8c0000 00000000 1900063d cfa8c9e0
<0> cfa8c9e8 cfa8c0c0 cfa8c000 d0a27f0c 199d84b4 cfa8c200 00000010 d09bfdc7
<0> 00000000 00000000 ffffffff d08e0d28 cf9263c0 00000001 cfa09cc4 00000000
Call Trace:
[<d0a27f0c>] ? ath5k_hw_attach+0xc8c/0x3c10 [ath5k]
[<d09bfdc7>] ? __ieee80211_request_smps+0x1347/0x1580 [mac80211]
[<d08e0d28>] ? nl80211_send_scan_start+0x7b8/0x4520 [cfg80211]
[<c10f5db9>] ? nla_parse+0x59/0xc0
[<c11ca8d9>] ? genl_rcv_msg+0x169/0x1a0
[<c11ca770>] ? genl_rcv_msg+0x0/0x1a0
[<c11c7e68>] ? netlink_rcv_skb+0x38/0x90
[<c11c9649>] ? genl_rcv+0x19/0x30
[<c11c7c03>] ? netlink_unicast+0x1b3/0x220
[<c11c893e>] ? netlink_sendmsg+0x26e/0x290
[<c11a409e>] ? sock_sendmsg+0xbe/0xf0
[<c1032780>] ? autoremove_wake_function+0x0/0x50
[<c104d846>] ? __alloc_pages_nodemask+0x106/0x530
[<c1074933>] ? do_lookup+0x53/0x1b0
[<c10766f9>] ? __link_path_walk+0x9b9/0x9e0
[<c11acab0>] ? verify_iovec+0x50/0x90
[<c11a42b1>] ? sys_sendmsg+0x1e1/0x270
[<c1048e50>] ? find_get_page+0x10/0x50
[<c104a96f>] ? filemap_fault+0x5f/0x370
[<c1059159>] ? __do_fault+0x319/0x370
[<c11a55b4>] ? sys_socketcall+0x244/0x290
[<c101962c>] ? do_page_fault+0x1ec/0x270
[<c1019440>] ? do_page_fault+0x0/0x270
[<c1002ae5>] ? syscall_call+0x7/0xb
Code: 00 b8 fe 00 00 00 b9 f8 53 a3 d0 89 5c 24 14 89 7c 24 10 89 44 24
0c 89 6c 24 08 89 4c 24 04 c7 04 24 35 4f a3 d0 e8 7c 30 60 f0 <0f> b7
43 06 ba 06 00 00 00 a8 10 75 0e 83 e0 20 83 f8 01 19 d2
EIP: [<d0a1ff24>] ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k] SS:ESP
0068:cfa09bf4
CR2: 0000000000000006
---[ end trace 54f73d6b10ceb87b ]---
Cc: stable@kernel.org
Reported-by: Steve Brown <sbrown@cortland.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This removes dma_get_ops() prefetch optimization in bnx2.
bnx2 uses dma_get_ops() to see if dma_sync_single_for_cpu() is
noop. bnx2 does prefetch if it's noop.
But dma_get_ops() isn't available on all the architectures (only the
architectures that uses dma_map_ops struct have it). Using
dma_get_ops() in drivers leads to compilation breakage on many
architectures.
This patch removes dma_get_ops() and changes bnx2 to do prefetch on
all the architectures. This adds useless prefetch on non-coherent
architectures but this is harmless. It is also unlikely to cause the
performance drop.
[ Remove now unused local variable 'pdev' -DaveM ]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
