summaryrefslogtreecommitdiffstats
path: root/drivers/net
AgeCommit message (Collapse)Author
2010-10-05net/phy: fix many "defined but unused" warningsUwe Kleine-König
MODULE_DEVICE_TABLE only expands to something if it's compiled for a module. So when building-in support for the phys, the mdio_device_id tables are unused. Marking them with __maybe_unused fixes the following warnings: drivers/net/phy/bcm63xx.c:134: warning: 'bcm63xx_tbl' defined but not used drivers/net/phy/broadcom.c:933: warning: 'broadcom_tbl' defined but not used drivers/net/phy/cicada.c:162: warning: 'cicada_tbl' defined but not used drivers/net/phy/davicom.c:222: warning: 'davicom_tbl' defined but not used drivers/net/phy/et1011c.c:114: warning: 'et1011c_tbl' defined but not used drivers/net/phy/icplus.c:137: warning: 'icplus_tbl' defined but not used drivers/net/phy/lxt.c:226: warning: 'lxt_tbl' defined but not used drivers/net/phy/marvell.c:724: warning: 'marvell_tbl' defined but not used drivers/net/phy/micrel.c:234: warning: 'micrel_tbl' defined but not used drivers/net/phy/national.c:154: warning: 'ns_tbl' defined but not used drivers/net/phy/qsemi.c:141: warning: 'qs6612_tbl' defined but not used drivers/net/phy/realtek.c:82: warning: 'realtek_tbl' defined but not used drivers/net/phy/smsc.c:257: warning: 'smsc_tbl' defined but not used drivers/net/phy/ste10Xp.c:135: warning: 'ste10Xp_tbl' defined but not used drivers/net/phy/vitesse.c:195: warning: 'vitesse_tbl' defined but not used Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-04qlcnic: set mtu lower limitSritej Velaga
Setting mtu < 68 is not supported. Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-04qlcnic: cleanup port mode settingSritej Velaga
Port mode setting is not required for Qlogic CNA adapters. Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-04qlcnic: sparse warning fixesSucheta Chakraborty
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-04qlcnic: fix vlan TSO on big endian machineSucheta Chakraborty
o desc->vlan_tci is in __le16 format. Doing htons and cpu_to_le64 again on vlan_tci, result in invalid value on ppc. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-04qlcnic: fix endianess for lroSucheta Chakraborty
ipaddress in ifa->ifa_address field are in big endian format. Also device requires ip address in big endian only. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-04qlcnic: fix diag registerAmit Kumar Salecha
regs_buff[i] and diag_registers[j] array should use different index variable. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-04qlcnic: fix eswitch statsAmit Kumar Salecha
Some of the counters are not implemented in fw. Fw return NOT AVAILABLE VALUE as (0xffffffffffffffff). Adding these counters, result in invalid value. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-04qlcnic: fix internal loopback testAmit Kumar Salecha
o Loop 10 times with delay of 1 ms to rcv packet. o Print garbage packet. o Try send/receive MAX(16) packet, instead of exit from test, if a packet is not received. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-04Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: net/ipv4/Kconfig net/ipv4/tcp_timer.c
2010-10-03be2net: add multiple RX queue supportSathya Perla
This patch adds multiple RX queue support to be2net. There are upto 4 extra rx-queues per port into which TCP/UDP traffic can be hashed into. Some of the ethtool stats are now displayed on a per queue basis. Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-03Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2010-10-03cxgb4: remove a bogus PCI function number checkDimitris Michailidis
Remove a bogus PCI function number check from the driver's .remove method that causes pci_release_regions not to be called for function 0 if additional functions are attached and one of them is used as primary. Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-03drivers-net-tulip-de4x5c-fix-copy-length-in-de4x5_ioctl-checkpatch-fixesAndrew Morton
ERROR: trailing statements should be on next line #23: FILE: drivers/net/tulip/de4x5.c:5477: + if (copy_to_user(ioc->data, tmp.lval, ioc->len)) return -EFAULT; total: 1 errors, 0 warnings, 8 lines checked ./patches/drivers-net-tulip-de4x5c-fix-copy-length-in-de4x5_ioctl.patch has style problems, please review. If any of these errors are false positives report them to the maintainer, see CHECKPATCH in MAINTAINERS. Please run checkpatch prior to sending patches Cc: Dan Rosenberg <dan.j.rosenberg@gmail.com> Cc: Grant Grundler <grundler@parisc-linux.org> Cc: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-03netdev: Depend on INET before selecting INET_LROBen Hutchings
Since 'select' ignores dependencies, drivers that select INET_LRO must depend on INET. This fixes the broken configuration reported in <http://article.gmane.org/gmane.linux.kernel/825646>. Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-01Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
2010-10-01enic: Make local functions staticVasanthy Kolluri
Make functions used locally in a file as static Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-01enic: Remove dead codeVasanthy Kolluri
Removed code that is unused Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by: Roopa Prabhu <roprabhu@cisco.com> Signed-off-by: David Wang <dwang2@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-01tg3: Update version to 3.114Matt Carlson
This patch updates the tg3 version to 3.114. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-01tg3: Add extend rx ring sizes for 5717 and 5719Matt Carlson
This patch increases the rx ring sizes for those asic revs that support them. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-01tg3: Prepare for larger rx ring sizesMatt Carlson
This patch adds two new variables to track the size of the standard and jumbo rx producer ring sizes. The code is then pivoted to these variables from preprocessor constants. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-01tg3: Futureproof the loopback testMatt Carlson
There are other multiqueue modes 5717 and 5719 devices can assume. This patch makes sure that the loopback test is safe, should those other modes be enabled in the future. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-01tg3: Cleanup missing VPD partno sectionMatt Carlson
This patch cleans up the default VPD partno section. New entries for 5717 asic rev devices were also added. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-01tg3: Remove 5724 device IDMatt Carlson
This product was never released to the public. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-01tg3: 5719: Prevent tx data corruptionMatt Carlson
This patch enables a bit that prevents read DMA overflows and adjusts the txmbuf margin from the hardware default. The combination of these modifications prevents a tx data corruption issue we were seeing on the 5719. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-01tg3: Fix potential netpoll crashMatt Carlson
Up until now the tg3 driver would call netif_napi_add() for the maximum number of NAPI instances the driver could use. The problem is that netpoll could call tg3_poll() on instances that are not active. The net effect is that the driver will crash attempting to dereference uninitialized pointers. The fix is to only allocate as many NAPI instances as the driver would use in tg3_open() and deleted them in tg3_close(). Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-30e1000e: 82579 performance improvementsBruce Allan
The initial support for 82579 was tuned poorly for performance. Adjust the packet buffer allocation appropriately for both standard and jumbo frames; and for jumbo frames increase the receive descriptor pre-fetch, disable adaptive interrupt moderation and set the DMA latency tolerance. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-30e1000e: use hardware writeback batchingJesse Brandeburg
Most e1000e parts support batching writebacks. The problem with this is that when some of the TADV or TIDV timers are not set, Tx can sit forever. This is solved in this patch with write flushes using the Flush Partial Descriptors (FPD) bit in TIDV and RDTR. This improves bus utilization and removes partial writes on e1000e, particularly from 82571 parts in S5500 chipset based machines. Only ES2LAN and 82571/2 parts are included in this optimization, to reduce testing load. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-30ixgbe: fix link issues and panic with shared interrupts for 82598Emil Tantilov
Fix possible panic/hang with shared Legacy interrupts by not enabling interrupts when interface is down. Also fixes an intermittent link by enabling LSC upon exit from ixgbe_intr() This patch adds flags to ixgbe_irq_enable() to allow for some flexibility when enabling interrupts. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-30net: pxa168_etc.c recognize additional contributorsPhilip Rakity
Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Sachin Sanap <ssanap@marvell.com> Signed-off-by: Mark Brown <markb@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-30Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2010-09-29de2104x: remove experimental statusOndrej Zary
It should be ready after 8 years...remove the experimental dependency. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-29de2104x: disable media debug messages by defaultOndrej Zary
Print media debug messages only when HW debug is enabled. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-29myri10ge: DCA update (resubmit)Andrew Gallatin
This patch contains the following DCA improvements to myri10ge: 1) Finally move myri10ge to use dca3 API 2) Disable PCIe relaxed ordering when enabling DCA on myri10ge. This provides a performance boost on Nehalem based Xeons 3) Make sure to properly initialize NIC's DCA state when it is enabled, rather than giving the NIC a bogus tag (0) and waiting for the first received packet to trigger an update. Not using a real tag can cause hardware exceptions on some motherboards when a CPU socket is empty. 3) Always update the cached CPU when our interrupt affinity changes so as to avoid excessive calls to dca3_get_tag() Signed-off-by: Andrew Gallatin <gallatin@myri.com> Signed-off-by: Loic Prylli <loic@myri.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-29bnx2x: Moved enabling of MSI to the bnx2x_set_num_queues()Dmitry Kravkov
Moved enabling of MSI to the bnx2x_set_num_queues() - the same functions that handles the initialization of the MSI-X. From: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-29dummy: percpu stats and lockless xmitEric Dumazet
Converts dummy network device driver to : - percpu stats - 64bit stats - lockless xmit (NETIF_F_LLTX) - performance features added (NETIF_F_SG | NETIF_F_FRAGLIST | NETIF_F_TSO | NETIF_F_NO_CSUM | NETIF_F_HIGHDMA) Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-28carl9170: interrupt urbs must not set URB_ZERO_PACKETChristian Lamparter
This patch fixes a bug in the driver which was exposed by CONFIG_USB_DEBUG: "usb 1-1.6.3: BOGUS urb flags, 40 --> 0" The transfer flag "URB_ZERO_PACKET" is only valid for bulk urbs. Reported-by: André Erdmann Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28ath5k: Fix bitmasks and typos for PCU Diagnostic registerBruno Randolf
As reported by Ryan Niemi, some bitmasks in the register definition for the PCU Diagnostic register (DIAG_SW) were missing a zero at the end. While at it fix some typos and add more comments. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28ath5k: Disable interrupts in ath5k_hw_get_tsf64Bruno Randolf
The code in ath5k_hw_get_tsf64() is time critical and will return wrong results if we get interrupted, so disable local interrupts. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28ath5k: Increase "fudge" for beacon timersBruno Randolf
We use FUDGE to make sure the next TBTT is ahead of the current TU. Since we later substract AR5K_TUNE_SW_BEACON_RESP (10) in the timer configuration we need to make sure it is bigger than that. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28ath5k: Check and fix ATIM windowBruno Randolf
This patch adds sanity-checks for the beacon timers and especially the ATIM window to ath5k. It is basically the same what i did for madwifi two years ago and fixes a problem in IBSS mode which has been described as "ramping" pings. See the code comments for a more detailed description and these links: http://madwifi-project.org/ticket/1154 http://madwifi-project.org/changeset/3867 http://thread.gmane.org/gmane.linux.drivers.madwifi.devel/6066 Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28ath5k: Remove unused variable for atim windowBruno Randolf
It's not used and it's unlikely we will ever implement ATIM. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28carl9170: revamp carl9170_tx_prepareChristian Lamparter
David Miller complained about the driver's excessive use of variables in __packed structs. While I did not fully agree with his sole "performance" argument on all accounts. I do see some room for improvement in hot-paths on architectures without an efficient access to unaligned elements. This first patch (dare I say?) optimizes an important tx hot-path in the driver: carl9170_tx_prepare. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28carl9170: fix WARN_ON triggered by Broadcom HT STAsChristian Lamparter
Broadcom's Windows driver for the 4313 advertises an ampdu density of 7 => 16 us. The AR9170 MAC on the other hand only supports densities up to 8 us. This patch removes the noisy WARN_ON, because there is nothing we can do about it. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28carl9170: fix tx_ampdu_upload counterChristian Lamparter
tx_ampdu_upload was not decreased when an a-MPDU frame had to be kicked out from the tx_pending queues. This broke ampdu aggregation, because the scheduler waits until tx_ampdu_upload drops to zero, before making the next aggregate. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28carl9170: remove lost-frame workaroundChristian Lamparter
This patch removes some cruft, which survived the RFC review phase. Originally, carl9170_tx_ampdu_queue erroneously dropped a lot of frames. As a result the ampdu scheduler bogged down quite frequently and the affected BA session timed out. However this bug has been fixed and the WA and its debugfs counter is no longer useful. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28carl9170: angle brackets for wiki linkChristian Lamparter
"The convention seems to be angle brackets around URLS in Kconfig." -- Finn Thain (to update web addresses in the kernel) Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28carl9170: remove non-standard ba session teardownChristian Lamparter
802.11n-2009 demands in 11.2.1: " When a STA enters normal (non-APSD) PS mode, any downlink Block ACK agreement without an associated schedule is suspended for the duration of this PS mode." The operative word is "suspended" and not terminated. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28iwl3945: queue the right work if the scan needs to be abortedFlorian Mickler
iwl3945's scan_completed calls into the mac80211 stack which triggers a warn on if there is no scan outstanding. This can be avoided by not calling scan_completed but abort_scan in iwl3945_request_scan in the done: branch of the function which is used as an error out. The done: branch seems to be an error-out branch, as, for example, if iwl_is_ready(priv) returns false the done: branch is executed. NOTE: I'm not familiar with the driver at all. I just quickly scanned as a reaction to https://bugzilla.kernel.org/show_bug.cgi?id=17722 the users of scan_completed in the iwl3945 driver and noted the odd discrepancy between the comment above this instance and the comment in mac80211 scan_completed function. Signed-off-by: Florian Mickler <florian@mickler.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-28pch_gbe: add header filesRandy Dunlap
Fix build errors, more header files needed. drivers/net/pch_gbe/pch_gbe_main.c:965: error: implicit declaration of function 'tcp_hdr' drivers/net/pch_gbe/pch_gbe_main.c:965: error: invalid type argument of '->' (have 'int') drivers/net/pch_gbe/pch_gbe_main.c:968: error: invalid type argument of '->' (have 'int') drivers/net/pch_gbe/pch_gbe_main.c:976: error: implicit declaration of function 'udp_hdr' drivers/net/pch_gbe/pch_gbe_main.c:976: error: invalid type argument of '->' (have 'int') drivers/net/pch_gbe/pch_gbe_main.c:980: error: invalid type argument of '->' (have 'int') Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-02-19 01:11:03 +0000