summaryrefslogtreecommitdiffstats
path: root/drivers/net
AgeCommit message (Collapse)Author
2011-07-21iwlagn: radio sensor offset in le16 formatWey-Yi Guy
For temperature offset calibration, send radio sensor offset in le16 format Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-21iwlagn: define valid init calibration maskWey-Yi Guy
Use the valid calibration mask for init calibration Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-21iwlagn: remove legacy calibration commandWey-Yi Guy
IWL_PHY_CALIBRATE_DIFF_GAIN_CMD is for legacy device, remove it Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-21iwlagn: set correct calibration flagWey-Yi Guy
Set calibration config flag for complete notification Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-21iwlagn: kill iwlagn_setup_deferred_workEmmanuel Grumbach
Since iwlagn_setup_deferred_work is always called, fold it into iwl_setup_deferred_work. BT related works are setup by the new bt_setup_deferred_work lib_ops. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
2011-07-21iwlagn: kill iwlagn_rx_handler_setupEmmanuel Grumbach
Since iwlagn_rx_handler_setup is always called, fold it into iwl_rx_handler_setup. BT related handlers are setup by the new bt_rx_handler_setup lib_ops. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
2011-07-21iwlagn: add kick_nic API to transport layerEmmanuel Grumbach
kick_nic means to remove the RESET bit from the embedded CPU Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
2011-07-20libertas: only enable mesh when interface is activeDaniel Drake
Previously, the mesh was running whenever the appropriate hardware and firmware was present. Now we only run the mesh when the interface is running. Also simplifies interface management a little. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-20libertas: mesh: misc cleanupDaniel Drake
Remove unused blindlist code. Mark a few items const and static where possible. Involved some code re-ordering, but no code changes. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-20wireless: mwifiex: print hw address via %pMAndy Shevchenko
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-20wireless: ath9k: use %pM to print MACAndy Shevchenko
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: "Luis R. Rodriguez" <lrodriguez@atheros.com> Cc: ath9k-devel@lists.ath9k.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-20wireless: rtlwifi: throw away MAC_FMT and use %pM insteadAndy Shevchenko
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-20carl9170: fix sparse warnings enabled by CONFIG_SPARSE_RCU_POINTERPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-20ath5k: merge ath5k_hw and ath5k_softcPavel Roskin
Both ath5k_hw and ath5k_softc represent one instance of the hardware. This duplication is historical and is not needed anymore. Keep the name "ath5k_hw" for the merged structure and "ah" for the variable pointing to it. "ath5k_hw" is shorter than "ath5k_softc", more descriptive and more widely used. Put the combined structure to ath5k.h where the old ath5k_softc used to be. Move some code from base.h to ath5k.h as needed. Remove memory allocation for struct ath5k_hw and the corresponding error handling. Merge iobase and ah_iobase fields. Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-19b43: bcma: implement full core resetRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-19b43: correctly display longer chipsets idsRafał Miłecki
Some of the newer Broadcom chipsets have longe names like BCM43224, BCM43225, etc. However Broadcom decided to keep using u16 for storing them. Use %X or %d depending on chip_id value to avoid BCMA8D8, etc. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-19b43: HT-PHY: fix masks in radio ctlRafał Miłecki
Old masks were causing ugly, delayed lock ups. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-19b43: bcma: read info about supported bandsRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-19b43: bcma: define 80211 core specific IO status bitsRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-19b43: HT-PHY: fix typo in 0x2059 radio initRafał Miłecki
Following operation was incorrectly translated: radio_read(0x0011) -> 0xffff radio_write(0x0011) <- 0xfff7 Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-19b43: HT-PHY: find channel entry with regs dataRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-19b43: HT-PHY: switch to channel after enabling radioRafał Miłecki
Also change the default channel to 11. This is the first channel closed driver switches to. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-19b43: use agent R/W ops for BCMA_IOCTLRafał Miłecki
BCMA_IOCTL is register in agent (AKA wrapper) core, we need to use special R/W ops for it. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-18ath9k: Fix some smatch warningsRajkumar Manoharan
drivers/net/wireless/ath/ath9k/hif_usb.c +135 hif_usb_mgmt_cb(6) warn: variable dereferenced before check 'cmd' drivers/net/wireless/ath/ath9k/btcoex.c +77 ath9k_hw_init_btcoex_hw(38) error: buffer overflow 'ah->hw_gen_timers.gen_timer_index' 32 <= 2009813776 Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-18ath9k: Fix sparse warningsRajkumar Manoharan
drivers/net/wireless/ath/ath9k/init.c:199:21: warning: context imbalance in 'ath9k_reg_rmw' - different lock contexts for basic block drivers/net/wireless/ath/ath9k/xmit.c:1175:31: warning: context imbalance in 'ath_drain_txq_list' - unexpected unlock drivers/net/wireless/ath/ath9k/xmit.c:2047:23: warning: context imbalance in 'ath_tx_process_buffer' - unexpected unlock drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3041:24: warning: cast to restricted __le32 Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-18b43: bus: drop inline from SSB functionsRafał Miłecki
We use all that functions by pointers only. This forces compiler to create additional duplicated functions that are not inline. Noticed by Michael in similar bcma code. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-18carl9170: set beacon xmit power to the maxChristian Lamparter
Harshal Chhaya discovered during network tests, that several of his clients dropped-off the network. The captured packets shows that the beacons sent by the AP are at a much lower power than the other data packets. The reason for this mishap: The driver never updated the beacon phy register, so all beacons were always sent at the lowest power. Reference: http://marc.info/?l=linux-wireless&m=131067225105801 Reported-by: Harshal Chhaya <harshal@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-18carl9170: move beacon_update into tx.cChristian Lamparter
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-18carl9170 firmware: update firmware headersChristian Lamparter
* reserves feature bit for CCA counters * extends hardware register file definitions Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-18ath9k: use ath_opmode_to_string()Pavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-18ath9k: remove defines in reg.h that exist in ../reg.hPavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-18ath9k: use get_unaligned_{b16, le16, le32} where possiblePavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-18ath: use get_unaligned_le{16,32} in ath_hw_keysetmac()Pavel Roskin
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-07-16iwlagn: add tx start API to transport layerEmmanuel Grumbach
tx start will start the tx queues: basically configure the SCD Remove the IWLAGN prefix to SCD defines on the way. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
2011-07-16iwlagn: move all the ICT related functions to iwl-trans-rx-pcie.cEmmanuel Grumbach
Since the ICT is transport related, move all its functions to the transport layer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: move iwlagn_stop_device to transport layerEmmanuel Grumbach
Since iwlagn_stop_device was the only caller to the rx_stop / tx_stop, these two don't need to be API any more. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
2011-07-16iwlagn: move tx transport functions to iwl-trans-tx-pcie.cEmmanuel Grumbach
There are still a few functions here and there that should be put in the transport layer. Mainly the functions that are related to the reclaim flow. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: move rx transport functions to iwl-trans-rx-pcie.cEmmanuel Grumbach
Also create a new file: iwl-trans-int-pcie.h which will include the non static functions that are shared among the current pcie transport layer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: remove indirection for iwlagn_hw_valid_rtc_data_addrFry, Donald H
Not needed since the driver split. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: calibration bitmapWey-Yi Guy
Define bitmap for calibration Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: set default of uCode ownership to driverHsu, Kenny
The driver should take the ownership of the uCode as default setting for later operations after interface up. Signed-off-by: Kenny Hsu <kenny.hsu@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: simplify TX flags assignmentsJohannes Berg
The first assignment of TX_CMD_FLG_SEQ_CTL_MSK for ack-expected mgmt frames is overwritten later in the function, so it's useless. Also, probe response frames, BACK request and others there are mutually exclusive so can be moved into an else branch. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: add comment to tx and get_tx_cmd in iwl_trans_opsEmmanuel Grumbach
Those comments were missed in a previous commit. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: comments for iwl_cfgWey-Yi Guy
Modify the comments for iwl_cfg, no functional changes Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: another double indirect removedWey-Yi Guy
Another clean up work after driver split Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: remove dual-indirect call to simply the codeWey-Yi Guy
After driver split, no need to make the code so complex Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: remove un-necessary fileWey-Yi Guy
Most of the functions in iwl-agn-hcmd are move to other files, no point to keep the file anymore. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: move the Rx dispatching to the upper layerEmmanuel Grumbach
The upper layer receives a pointer to an iwl_rx_mem_buffer. I would prefer the upper layer to receive a pointer to an iwl_rx_packet, but this is impossible since the Rx path needs to add the address of the page to the skb. I may find a solution later. All the pre_rx_handler and notification code has been moved to the upper layer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: move sync_irq to transport layerEmmanuel Grumbach
Since all the irq / tasklet is now handled in the transport layer, it should give an API to ensure that all the irq / tasklet have finished running. This will allow the upper layer to release all its resources. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-07-16iwlagn: move the tasklet / irq to the transport layerEmmanuel Grumbach
PCIe doesn't provide any ISR registration API, whereas other buses do. Hence, we need to move the tasklet and irq to the transport layer to allow this flexibility. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-01 20:37:01 +0000