| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull RDMA/InfiniBand fixes from Roland Dreier:
- Fix some rough edges from the "IP addressing for IBoE" merge
- Other misc fixes, mostly to hardware drivers
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (21 commits)
RDMA/ocrdma: Fix load time panic during GID table init
RDMA/ocrdma: Fix traffic class shift
IB/iser: Fix use after free in iser_snd_completion()
IB/iser: Avoid dereferencing iscsi_iser conn object when not bound to iser connection
IB/usnic: Fix smatch endianness error
IB/mlx5: Remove dependency on X86
mlx5: Add include of <linux/slab.h> because of kzalloc()/kfree() use
IB/qib: Add missing serdes init sequence
RDMA/cxgb4: Add missing neigh_release in LE-Workaround path
IB: Report using RoCE IP based gids in port caps
IB/mlx4: Build the port IBoE GID table properly under bonding
IB/mlx4: Do IBoE GID table resets per-port
IB/mlx4: Do IBoE locking earlier when initializing the GID table
IB/mlx4: Move rtnl locking to the right place
IB/mlx4: Make sure GID index 0 is always occupied
IB/mlx4: Don't allocate range of steerable UD QPs for Ethernet-only device
RDMA/amso1100: Fix error return code
RDMA/nes: Fix error return code
IB/mlx5: Don't set "block multicast loopback" capability
IB/mlx5: Fix binary compatibility with libmlx5
...
|
|
Remove Kconfig dependency of mlx5_ib/mlx5_core on X86, since there is
no such dependency in reality.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Pull networking updates from David Miller:
1) Fix flexcan build on big endian, from Arnd Bergmann
2) Correctly attach cpsw to GPIO bitbang MDIO drive, from Stefan Roese
3) udp_add_offload has to use GFP_ATOMIC since it can be invoked from
non-sleepable contexts. From Or Gerlitz
4) vxlan_gro_receive() does not iterate over all possible flows
properly, fix also from Or Gerlitz
5) CAN core doesn't use a proper SKB destructor when it hooks up
sockets to SKBs. Fix from Oliver Hartkopp
6) ip_tunnel_xmit() can use an uninitialized route pointer, fix from
Eric Dumazet
7) Fix address family assignment in IPVS, from Michal Kubecek
8) Fix ath9k build on ARM, from Sujith Manoharan
9) Make sure fail_over_mac only applies for the correct bonding modes,
from Ding Tianhong
10) The udp offload code doesn't use RCU correctly, from Shlomo Pongratz
11) Handle gigabit features properly in generic PHY code, from Florian
Fainelli
12) Don't blindly invoke link operations in
rtnl_link_get_slave_info_data_size, they are optional. Fix from
Fernando Luis Vazquez Cao
13) Add USB IDs for Netgear Aircard 340U, from Bjørn Mork
14) Handle netlink packet padding properly in openvswitch, from Thomas
Graf
15) Fix oops when deleting chains in nf_tables, from Patrick McHardy
16) Fix RX stalls in xen-netback driver, from Zoltan Kiss
17) Fix deadlock in mac80211 stack, from Emmanuel Grumbach
18) inet_nlmsg_size() forgets to consider ifa_cacheinfo, fix from Geert
Uytterhoeven
19) tg3_change_mtu() can deadlock, fix from Nithin Sujir
20) Fix regression in setting SCTP local source addresses on accepted
sockets, caused by some generic ipv6 socket changes. Fix from
Matija Glavinic Pecotic
21) IPPROTO_* must be pure defines, otherwise module aliases don't get
constructed properly. Fix from Jan Moskyto
22) IPV6 netconsole setup doesn't work properly unless an explicit
source address is specified, fix from Sabrina Dubroca
23) Use __GFP_NORETRY for high order skb page allocations in
sock_alloc_send_pskb and skb_page_frag_refill. From Eric Dumazet
24) Fix a regression added in netconsole over bridging, from Cong Wang
25) TCP uses an artificial offset of 1ms for SRTT, but this doesn't jive
well with TCP pacing which needs the SRTT to be accurate. Fix from
Eric Dumazet
26) Several cases of missing header file includes from Rashika Kheria
27) Add ZTE MF667 device ID to qmi_wwan driver, from Raymond Wanyoike
28) TCP Small Queues doesn't handle nonagle properly in some corner
cases, fix from Eric Dumazet
29) Remove extraneous read_unlock in bond_enslave, whoops. From Ding
Tianhong
30) Fix 9p trans_virtio handling of vmalloc buffers, from Richard Yao
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (136 commits)
6lowpan: fix lockdep splats
alx: add missing stats_lock spinlock init
9p/trans_virtio.c: Fix broken zero-copy on vmalloc() buffers
bonding: remove unwanted bond lock for enslave processing
USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support
tcp: tsq: fix nonagle handling
bridge: Prevent possible race condition in br_fdb_change_mac_address
bridge: Properly check if local fdb entry can be deleted when deleting vlan
bridge: Properly check if local fdb entry can be deleted in br_fdb_delete_by_port
bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address
bridge: Fix the way to check if a local fdb entry can be deleted
bridge: Change local fdb entries whenever mac address of bridge device changes
bridge: Fix the way to find old local fdb entries in br_fdb_change_mac_address
bridge: Fix the way to insert new local fdb entries in br_fdb_changeaddr
bridge: Fix the way to find old local fdb entries in br_fdb_changeaddr
tcp: correct code comment stating 3 min timeout for FIN_WAIT2, we only do 1 min
net: vxge: Remove unused device pointer
net: qmi_wwan: add ZTE MF667
3c59x: Remove unused pointer in vortex_eisa_cleanup()
net: fix 'ip rule' iif/oif device rename
...
|
|
Trivial fix for init time stack trace occuring in
alx_get_stats64 upon start up. Should have been part of
commit adding the spinlock:
f1b6b106 alx: add alx_get_stats64 operation
Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bond enslave processing don't hold bond->lock anymore,
so release an unlocked rw lock will cause warning message,
remove the unwanted read_unlock(&bond->lock).
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Liu Junliang <liujunliang_ljl@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove occurrences of unused struct __vxge_hw_device pointer in functions
vxge_learn_mac() and vxge_rem_isr().
Detected by Coverity: CID 139839, CID 139842.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver description files give these descriptions to the vendor specific
ports on this modem:
VID_19D2&PID_1270&MI_00: "ZTE MF667 Diagnostics Port"
VID_19D2&PID_1270&MI_01: "ZTE MF667 AT Port"
VID_19D2&PID_1270&MI_02: "ZTE MF667 ATExt2 Port"
VID_19D2&PID_1270&MI_03: "ZTE MF667 ATExt Port"
VID_19D2&PID_1270&MI_04: "ZTE MF667 USB Modem"
VID_19D2&PID_1270&MI_05: "ZTE MF667 Network Adapter"
Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unused network device private data pointer 'vp' in function
vortex_eisa_cleanup(). Detected by Coverity: CID 139826.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove occurrences of unused pointer to network device private data in
functions dlci_header() and dlci_receive().
Detected by Coverity: CID 139844, CID 139845.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.14 stream!
For the mac80211 bits, Johannes says:
"This is just a collection of small fixes, the commit logs explain the
details. The only thing that isn't strictly a fix is the 5/10 MHz
enabling, I had forgotten this and there's little point in waiting
longer. The patch simply removes the force-disable code that I put in
when there was a problem with the userspace API (that has long been
fixed.)"
For the iwlwifi bits, Emmanuel says:
"I have an important fix that disables A band in case the driver thought
it was enabled, and the firmware disagreed. We ended up making the
firmware unhappy. I also fix the station table in AP mode and fix the
scan while we have BT working.
Johannes removes a static variable that could potentially lead to to
issues on multi-device setups and disables scheduled scan to avoid
issues with old versions of wpa_supplicant.
A small fix from David on scan and a few new device IDs for 7265."
On top of that...
Oleksij Rempel adds a USB ID to the ar5523 driver and changes the
default powersave setting for ath9k_htc to "off", due to observed
stability issues (based on an equivalent ath9k patch).
Stanislaw Gruszka similarly disables powersave for a couple of rt2x00
drivers. He also fixes a couple of scheduling while atomic issues
in ath9k_htc.
Sujith Manoharan rounds-out the powersave disables with one for ath9k.
He also fixes a build prolem with ath9k on ARM and fixes an ath9k Tx
power calculation.
Finally, Andrea Merello fixes a couple of lingering DMA mapping
problems in the rtl8180 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Commit ee45fd92c739db5b7950163d91dfe5f016af6d24 ("sfc: Use TX PIO
for sufficiently small packets") introduced the following warning:
drivers/net/ethernet/sfc/tx.c: In function 'efx_enqueue_skb':
drivers/net/ethernet/sfc/tx.c:432:1: warning: label 'finish_packet' defined but not used
Stick the label inside the same #ifdef that the code which calls
it uses. Note that this is only seen for arch that do not set
ARCH_HAS_IOREMAP_WC, such as arm, mips, sparc, ..., as the others
enable the write combining code and hence use the label.
Cc: Jon Cooper <jcooper@solarflare.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems like this function was intended to have special handling for
urb statuses of -ENOENT and -ECONNRESET. But now it just prints some
debugging and returns at the start of the function.
I have removed the dead code, it's still in the git history if anyone
wants to revive it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The submission of the interrupt transfer should be done after setting
the bit of WORK_ENABLE, otherwise the callback function would have
the opportunity to be returned directly.
Clear the bit of WORK_ENABLE before killing the interrupt transfer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x driver uses incorrect PF identifier to configure (in HW) the VF
interrupt scheme; As a result, in multi-function mode the configuration
for PFs with a high index (4+) will overflow and the PF will erroneously
configure a single ISR scheme for its VFs.
As a result, if such a VF uses multiple queues, interrupt generation will
stop after VF receives an Rx packet or sends a Tx packet on a queue
other than queue[0].
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Quoting David Vrabel -
"5780 cards cannot have jumbo frames and TSO enabled together. When
jumbo frames are enabled by setting the MTU, the TSO feature must be
cleared. This is done indirectly by calling netdev_update_features()
which will call tg3_fix_features() to actually clear the flags.
netdev_update_features() will also trigger a new netlink message for the
feature change event which will result in a call to tg3_get_stats64()
which deadlocks on the tg3 lock."
tg3_set_mtu() does not need to be under the tg3 lock since converting
the flags to use set_bit(). Move it out to after tg3_netif_stop().
Reported-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the original code, if tg3_readphy() fails then it does an unnecessary
check to verify "err" is still zero and then returns -EBUSY.
My static checker complains about the unnecessary "if (!err)" check and
anyway it is better to propagate the -EBUSY error code from
tg3_readphy() instead of hard coding it here. And really the original
code is confusing to look at.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Occasionally users want to know what parameters their Broadcom drivers
are running with. For example, a user may want to know if MSI is
disabled.
This patch has been compile tested.
Signed-off-by: James M Leddy <james.leddy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes old and unsupported CLPS711X IrDA driver.
Support for IrDA for CLPS711X serial port now provided by commit
4a33f1f59abd (serial: clps711x: Add support for N_IRDA line
discipline), so IrDA-mode can be turned ON with "irattach" tool
through "irtty" driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the mdio driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the ethernet driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Orignal code will not detect a DMA mapping failure, causing the HW
to attempt a DMA from an invalid address.
This patch add the error check and eventually simply drops the TX
packet if we can't map it for DMA.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In original code the old RX DMA buffer is unmapped and processed and at the end
of the isr a new buffer is mapped with pci_map_single and attached to the RX
descriptor.
If pci_map_single fails then the RX descriptor remains with no valid DMA buffer
attached.
In this condition the DMA will target where it shouldn't with obvious evil
consequences.
Simply avoiding re-arming the descriptor will prevent buggy DMA but it will
result soon in RX stuck.
This patch move the DMA mapping of the new buffer at the beginning of the ISR
(and it adds error check for pci_map_single success/fail).
If the DMA mapping fails then we do not unmap the old buffer and we re-arm the
descriptor without processing it, with the old DMA buffer still attached.
In this way we lose the currently RX-ed packet, but whenever next calls to
pci_map_single will succeed again,then the RX process will go on without stuck.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The recent patch to fix receive side flow control
(11b57f90257c1d6a91cee720151b69e0c2020cf6: xen-netback: stop vif thread
spinning if frontend is unresponsive) solved the spinning thread problem,
however caused an another one. The receive side can stall, if:
- [THREAD] xenvif_rx_action sets rx_queue_stopped to true
- [INTERRUPT] interrupt happens, and sets rx_event to true
- [THREAD] then xenvif_kthread sets rx_event to false
- [THREAD] rx_work_todo doesn't return true anymore
Also, if interrupt sent but there is still no room in the ring, it take quite a
long time until xenvif_rx_action realize it. This patch ditch that two variable,
and rework rx_work_todo. If the thread finds it can't fit more skb's into the
ring, it saves the last slot estimation into rx_last_skb_slots, otherwise it's
kept as 0. Then rx_work_todo will check if:
- there is something to send to the ring (like before)
- there is space for the topmost packet in the queue
I think that's more natural and optimal thing to test than two bool which are
set somewhere else.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Backend drivers shouldn't transistion to CLOSED unless the frontend is
CLOSED. If a backend does transition to CLOSED too soon then the
frontend may not see the CLOSING state and will not properly shutdown.
So, treat an unexpected backend CLOSED state the same as CLOSING.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When configuring GRE tunnel using OVS, tcp stream is distributed over
all RSS queues which may cause TCP reordering. It happens since OVS
uses L2GRE protocol when kernel gre uses IPGRE.
Patch defaults gre tunnel to L2GRE which allows proper RSS for L2GRE
packets and (implicitly) disables RSS for IPGRE traffic.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This device was mentioned in an OpenWRT forum. Seems to have a "standard"
Sierra Wireless ifnumber to function layout:
0: qcdm
2: nmea
3: modem
8: qmi
9: storage
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MII management bus clock is derived from the MAC clock by dividing it by
MIIMODER register CLKDIV field value. This value may need to be set up
in case it is undefined or its default value is too high (and
communication with PHY is too slow) or too low (and communication with
PHY is impossible). The value of CLKDIV is not specified directly, but
is derived from the MAC clock for the default MII management bus frequency
of 2.5MHz. The MAC clock may be specified in the platform data, or in
the 'clocks' device tree attribute.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OpenCores 10/100 Mbps MAC does not support speeds above 100 Mbps, but does
not disable advertisement when PHY supports them. This results in
non-functioning network when the MAC is connected to a gigabit PHY connected
to a gigabit switch.
The fix is to disable gigabit speed advertisement on attached PHY
unconditionally.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a Gigabit PHY device is connected to a 10/100Mbits capable Ethernet
MAC, the driver will restrict the phydev->supported modes to mask off
Gigabit. If the Gigabit PHY comes out of reset with the Gigabit features
set by default in MII_CTRL1000, it will keep advertising these feature,
so by the time we call genphy_config_advert(), the condition on
phydev->supported having the Gigabit features on is false, and we do not
update MII_CTRL1000 with updated values, and we keep advertising Gigabit
features, eventually configuring the PHY for Gigabit whilst the Ethernet
MAC does not support that.
This patches fixes the problem by ensuring that the Gigabit feature bits
are always cleared in MII_CTRL1000, if the PHY happens to be a Gigabit
PHY, and then, if Gigabit features are supported, setting those and
updating MII_CTRL1000 accordingly.
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The trigger and events functionality can be useful even if packet
timestamping is not used, but the required PTP clock is only enabled
when packet timestamping is started. This patch moves the clock enable
to when the interface is configured.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the external timestamping code is hardcoded to use the
rising edge even though the hardware has configurable event edge
detection. This patch changes the code to use falling edge detection
if PTP_FALLING_EDGE is set in the user supplied flags.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the SKBTX_IN_PROGRESS bit in tx_flags dp83640_txtstamp when doing
tx timestamps as per Documentation/networking/timestamping.txt.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fail_over_mac could be set to active or follow in any time for all modes,
so if the fail_over_mac is not none and the current mode is not active-backup,
the bond_set_mac_address() could not change the master and slave's MAC address.
In bond_set_mac_address(), the fail_over_mac should only affect AB mode, so modify
to check the mode in addition to fail_over_mac when setting bond's MAC address.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
processing
According to bonding.txt, the fail_over_ma should only affect active-backup mode,
but I found that the fail_over_mac could be set to active or follow in all
modes, this will cause new slave could not be set to bond's MAC address at
enslave processing and restore its own MAC address at removal processing.
The correct way to fix the problem is that we should not add restrictions when
setting options, just need to modify the bond enslave and removal processing
to check the mode in addition to fail_over_mac when setting a slave's MAC during
enslavement. The change active slave processing already only calls the fail_over_mac
function when in active-backup mode.
Thanks for Jay's suggestion.
The patch also modify the pr_warning() to pr_warn().
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit, "ath9k_hw: Fix incorrect Tx control power in AR9003 template"
fixed the incorrect values in the eeprom templates, but if
boards have already been calibrated with incorrect values,
they would still be using the wrong TX power. Fix this by assigning
a default value in such cases.
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use mdelay instead of udelay to fix this error:
ERROR: "__bad_udelay" [drivers/net/wireless/ath/ath9k/ath9k_hw.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mac80211 ->sta_rc_update() callback must be atomic. Since we have to
take mutex and do other operations that can sleep when sending fimrware
commands to device, the only option to satisfy atomicity requirement of
->sta_rc_update(), that I can see, is introduce work_struct and defer
uploading new rates to that work.
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Raw id and FW id should be switched.
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It is a copy/paste of patch provided by Sujith for ath9k.
"Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter."
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It is know that PS cause issues on that old devices, disable it by
default.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We have disabled it currently on other buses. PS can cause some issues,
not necessarily with our driver but on AP, that are not easy to debug.
Since behaviour differs on rt2800usb and rt2800pci, user usually blame
for malfunction rt2800usb driver, whereas issue is on AP side.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
sta_rc_update() callback must be atomic, hence we can not take mutexes
or do other operations, which can sleep in ath9k_htc_sta_rc_update().
I think we can just return from ath9k_htc_sta_rc_update(), if it is
called without IEEE80211_RC_SUPP_RATES_CHANGED bit. That will help
with scheduling while atomic bug for most cases (except mesh and IBSS
modes).
For mesh and IBSS I do not see other solution like creating additional
workqueue, because sending firmware command require us to sleep, but
this can be done in additional patch.
Patch partially fixes bug:
https://bugzilla.redhat.com/show_bug.cgi?id=990955
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The driver wasn't reading the NVM properly. While this
didn't lead to any issue until now, it seems that there
is an old version of the NVM in the wild.
In this version, the A band channels appear to be valid
but the SKU capabilities (another field of the NVM) says
that A band isn't supported at all.
With this specific version of the NVM, the driver would
think that A band is supported while the HW / firmware
don't. This leads to asserts.
Cc: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Not doing so will let BT kill our probe requests leading to
failures in scan.
Cc: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TX and RX rings share memory and descriptors. Maximal number of
descriptors reported is one less than the total available nuber of
descriptors. For the set operation the requested number of TX descriptors
is rounded down to the nearest power of two (driver logic requirement).
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
